Simplicity 5101604 Mower Belt Replacement, Regular Maintenance, C. 1/2” Breaker Bar D. Spring

Page 41
Mower Belt Replacement

Mower Belt Replacement

NOTICE

To avoid damaging belts, do NOT pry belts over pulleys.

1.Park the tractor on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key.

Figure 46. Mower PTO BeltWARNING

Spring loaded components can kick back causing injury.

Use extreme caution when rotating the idler arm with the breaker bar, due to the increased tension in the spring as the idler arm is being rotated. Injury may result in the breaker bar is prematurely release while the spring is under tension.

2.Using a 1/2” breaker bar, place the square end in the square hole located in the end of the idler arm (A, Figure 46). Carefully rotate the breaker bar counter- clockwise, which will relieve the tension on the belt exerted from the idler arm.

3.Slide the drive belt over the edge of the stationary idler pulley (B). Carefully release the tension on the breaker bar until the idler arm stops against the center spindle pulley.

4.Remove the old belt and replace with a new one. Make sure the V-side of the belt runs in the pulley grooves (Figure 47).

5.Install the drive belt on the PTO pulley, the spindle pulleys and all idler pulleys except the stationary pulley (B, Figure 47).

6.Carefully rotate the breaker bar counter-clockwiseand install the belt on the stationary idler pulley (B).

7.Carefully release the tension on the breaker bar.

8.Run the mower under no-load condition for about 5 minutes to break-in the new belt.

Regular Maintenance

A

B

D

C

Figure 46. Mower PTO Belt

A.Idler Arm

B.Stationary Idler Pulley

C.1/2” Breaker Bar

D.Spring

D

B

C

A

 

A

 

D

D

 

 

A

 

Figure 47. Mower PTO Belt Routing

A.Spindle Pulley

B.PTO Drive Belt

C.Spring-loaded Idler Pulley

D.Stationary Idler Pulley

39

Image 41
Contents Cobalt Series OPERATOR’S MANUAL30HP Zero-Turn Riders Mfg. NoDATE PURCHASED Operator Safety Table of ContentsFeatures & Controls Regular MaintenanceOperator Safety Operator SafetyOperating Safety Read the ManualMoving Parts Slope OperationThrown Objects Overhead Obstacles Roll Bar UseRetaining Walls, Drop-offs, and Water Enclosed Areas Fuel and MaintenanceTransporting and Storage General OperationEmissions Towed Equipment Ride-On UnitsIgnition System Operating on steep slopes can be dangerousSafe Handling of Gasoline Service and MaintenanceService & Maintenance Inspection of the Roll Bar Protective Structure Roll Bar InstructionsOperational Warnings INSPECT BUCKLE LATCH INSPECT WEBBING Inspection and Maintenance of the Roll Bar Seat Belt Safety DecalsOperational SAFETY Checks Safety Interlock SystemSafety Icons North American Safety IconsFeatures and Controls Features and ControlsIdentification Numbers CE ModelsPTO Power Take Off Switch Deck Lift Pedal, Cutting Height Adjustment Pin & Deck Lift Lock LeverControl Functions Parking BrakeHour Meter / Maintenance Reminder Ignition SwitchSeat Adjustment Lever Throttle ControlOperation General Operating SafetyOperation Checks Before StartingCheck Tire Pressures Seat AdjustmentPushing the Rider by Hand OperationFoot Pedal Adjustment Mowing Height AdjustmentTo Adjust Pedal Position Figure 5. Mowing Height Adjustment A. Cutting Height Adjustment Pin2. NOTE A warm engine may not require choking Starting the EngineStopping the Rider Basic Driving Zero-Turn Driving PracticeSmooth Travel Figure 7. Move Control Levers GraduallyPractice Turning Around a Corner Advanced DrivingFigure 10. Turning Around a Corner Figure 11. Turning in PlaceTo Lower the Roll Bar Raise and Lower the Roll BarTo Raise the Roll Bar StorageMowing Recommendations MowingHeight of Grass Figure 14. Proper Cutting HeightWhen and How Often to Mow Mowing MethodsNote Always operate the engine at full throttle when mowing How Much Grass to Cut Off When BroadcastingFigure 17. Trailer Weight Recommendations A. Clevis Pin B. Clip Attaching a TrailerProper Mulching Mulching Requires EXCELLENT Mowing ConditionsRegular Maintenance Regular MaintenanceMaintenance Schedule Safety ItemsFuel Filter Checking / Adding FuelChange Oil & Filter Inspect Muffler and Spark ArresterChange Hydraulic Oil Filter Check Hydraulic Oil LevelChange Interval Every 250 Hours Filter Part Number Figure 19. Checking Hydraulic Oil Level A. Hydraulic Oil ReservoirGrease LubricationLubricating the Front Casters Figure 21. Deck LubricationRemoving the Mower Blade Servicing The Mower BladesAvoid injury! Mower blades are sharp Inspecting the Mower BladesFigure 31. Tightening the Mower Blade for Installation Reinstalling the Mower BladesC. Mower Blade Air Lift Points Up For Installation Sharpening the Mower BladeBattery Maintenance Battery ChargingNOTE This unit is equipped with a maintenance-free BCIU1 battery Cleaning the Battery and CablesSpeed Balancing Adjustment Ground Speed Control Lever AdjustmentTo Adjust the Handle Alignment To Adjust the Handle PlacementReturn-to-Neutral Adjustment Neutral AdjustmentChecking the Adjustment Figure 35. Neutral Adjustment RH side shown A. Adjustment Linkage RodHydraulic Pump Drive Belt Replacement Parking Brake AdjustmentFigure 37. Parking Brake Adjustment A. Brake Spring B. Adjustment Nut Figure 38. Hydraulic Pump Drive Belt Replacement A. Pump Drive BeltTo adjust the spring pre-load Suspension AdjustmentSpring loaded components can kick back causing injury To adjust the upper mounting position Rear ShocksChecking the Deck Lift Rod Timing Adjustment Deck Lift Rod Timing Adjustment4. To adjust the inner lift rod Refer to Figure 9. To adjust the outer lift rod Refer to FigureDeck Lift Spring Deck Leveling AdjustmentRegular Maintenance NOTE Before adjusting the deck level, the deck lift rodFigure 46. Mower PTO Belt A. Idler Arm B. Stationary Idler Pulley Mower Belt ReplacementC. 1/2” Breaker Bar D. Spring Figure 47. Mower PTO Belt Routing A. Spindle Pulley B. PTO Drive BeltTroubleshooting TroubleshootingTroubleshooting the Rider PROBLEMTroubleshooting the Mower Troubleshooting the Rider continuedRider drive belt slips Brake will not holdStreaking Troubleshooting Common Cutting ProblemsScalping Stepped CuttingSpecifications SpecificationsDIMENSIONS Technical ManualsALONG APPROPRIATE DOTTED LINEANGLE OF THE SLOPE FOLDPage BELTS AND BLADES Product Quick Specs