Simplicity 543777-0113-E1 Product Quick Specs, Belts And Blades, Engine, Chassis, Transmissions

Page 48

Product Quick Specs:

Product Quick Specs:

ENGINE

30 HP Briggs & Stratton**

Make	Briggs & Stratton
Model	543777-0113-E1
Horsepower	30 @ 3200 rpm
Displacement	54.62 Cu in. (895 cc)
Electrical System	12 Volt, 20 amp. Alternator, Battery 340 CCA
Oil Capacity	2.4 qt (2,25 L) w/ filter

CHASSIS

Fuel Tank	Capacity: 11 gallons (41,6 L) total
Rear Wheels	Tire Size: 22 x 11.00 - 10
	Inflation Pressure: 15 psi (1,03 bar)
Front Wheels	Tire Size: 13 x 5.00 - 6
	Inflation Pressure: 25 psi (1,72 bar)

TRANSMISSIONS:

HydroGear PG-3H / HGM-12E 3131

Type	Pump and Wheel Motor
Hydraulic Fluid	Mobil 1™ 15W-50 oil OR
	Castrol Syntec™ 5W-50 oil
Speeds @ 3200 rpm	Foward: 0-10 MPH (0-16.09 km/h)
	Reverse: 0-5 MPH (0-5 km/h)
Continuous Torque	222 ft/lbs (301 Nm)
Output
Maximum Weight on	750 lbs (340 kg)
Axle

DIMENSIONS:

Overall Length	81” (208 cm)
Overall Width	72” (183 cm)
Height	70” (178 cm) w/ Roll Bar up
	59” (150 cm) w/ Roll Bar down
Weight (apx..)	1170 lbs (531 kg)
w/ 61” Mower Deck

BELTS AND BLADES:

Pump Drive Belt	5100555
Deck Drive Belt	5021724
Mower Blade	5020842

www.simplicitymfg.com

Briggs & Stratton Power Products Group, LLC. Copyright © 2008 Briggs & Stratton Corporation Milwaukee, WI, USA. All rights reserved.

The Simplicity logo is a trademark of Briggs & Stratton Corporation Milwaukee, WI, USA.

Image 48

Contents OPERATOR’S MANUAL Cobalt Series30HP Zero-Turn Riders Mfg. NoDATE PURCHASED Table of Contents Operator SafetyFeatures & Controls Regular MaintenanceOperator Safety Operator SafetyOperating Safety Read the ManualSlope Operation Thrown ObjectsMoving Parts Roll Bar Use Retaining Walls, Drop-offs, and WaterOverhead Obstacles Fuel and Maintenance Enclosed AreasGeneral Operation Transporting and StorageTowed Equipment Ride-On Units EmissionsIgnition System Operating on steep slopes can be dangerousService and Maintenance Service & MaintenanceSafe Handling of Gasoline Roll Bar Instructions Operational WarningsInspection of the Roll Bar Protective Structure Inspection and Maintenance of the Roll Bar Seat Belt INSPECT BUCKLE LATCH INSPECT WEBBINGSafety Decals Safety Interlock System Operational SAFETY ChecksSafety Icons North American Safety IconsFeatures and Controls Features and ControlsIdentification Numbers CE ModelsDeck Lift Pedal, Cutting Height Adjustment Pin & Deck Lift Lock Lever PTO Power Take Off SwitchControl Functions Parking BrakeIgnition Switch Hour Meter / Maintenance ReminderSeat Adjustment Lever Throttle ControlGeneral Operating Safety OperationOperation Checks Before StartingSeat Adjustment Check Tire PressuresPushing the Rider by Hand OperationMowing Height Adjustment Foot Pedal AdjustmentTo Adjust Pedal Position Figure 5. Mowing Height Adjustment A. Cutting Height Adjustment PinStarting the Engine Stopping the Rider2. NOTE A warm engine may not require choking Zero-Turn Driving Practice Basic DrivingSmooth Travel Figure 7. Move Control Levers GraduallyAdvanced Driving Practice Turning Around a CornerFigure 10. Turning Around a Corner Figure 11. Turning in PlaceRaise and Lower the Roll Bar To Lower the Roll BarTo Raise the Roll Bar StorageMowing Mowing RecommendationsHeight of Grass Figure 14. Proper Cutting HeightMowing Methods When and How Often to MowNote Always operate the engine at full throttle when mowing How Much Grass to Cut Off When BroadcastingAttaching a Trailer Figure 17. Trailer Weight Recommendations A. Clevis Pin B. ClipProper Mulching Mulching Requires EXCELLENT Mowing ConditionsRegular Maintenance Regular MaintenanceMaintenance Schedule Safety ItemsChecking / Adding Fuel Fuel FilterChange Oil & Filter Inspect Muffler and Spark ArresterCheck Hydraulic Oil Level Change Hydraulic Oil FilterChange Interval Every 250 Hours Filter Part Number Figure 19. Checking Hydraulic Oil Level A. Hydraulic Oil ReservoirLubrication GreaseLubricating the Front Casters Figure 21. Deck LubricationServicing The Mower Blades Removing the Mower BladeAvoid injury! Mower blades are sharp Inspecting the Mower BladesReinstalling the Mower Blades Figure 31. Tightening the Mower Blade for InstallationC. Mower Blade Air Lift Points Up For Installation Sharpening the Mower BladeBattery Charging Battery MaintenanceNOTE This unit is equipped with a maintenance-free BCIU1 battery Cleaning the Battery and CablesGround Speed Control Lever Adjustment Speed Balancing AdjustmentTo Adjust the Handle Alignment To Adjust the Handle PlacementNeutral Adjustment Return-to-Neutral AdjustmentChecking the Adjustment Figure 35. Neutral Adjustment RH side shown A. Adjustment Linkage RodParking Brake Adjustment Hydraulic Pump Drive Belt ReplacementFigure 37. Parking Brake Adjustment A. Brake Spring B. Adjustment Nut Figure 38. Hydraulic Pump Drive Belt Replacement A. Pump Drive BeltSuspension Adjustment To adjust the spring pre-loadSpring loaded components can kick back causing injury To adjust the upper mounting position Rear ShocksDeck Lift Rod Timing Adjustment Checking the Deck Lift Rod Timing Adjustment4. To adjust the inner lift rod Refer to Figure 9. To adjust the outer lift rod Refer to FigureDeck Leveling Adjustment Deck Lift SpringRegular Maintenance NOTE Before adjusting the deck level, the deck lift rodMower Belt Replacement Figure 46. Mower PTO Belt A. Idler Arm B. Stationary Idler PulleyC. 1/2” Breaker Bar D. Spring Figure 47. Mower PTO Belt Routing A. Spindle Pulley B. PTO Drive BeltTroubleshooting TroubleshootingTroubleshooting the Rider PROBLEMTroubleshooting the Rider continued Troubleshooting the MowerRider drive belt slips Brake will not holdTroubleshooting Common Cutting Problems StreakingScalping Stepped CuttingSpecifications SpecificationsDIMENSIONS Technical ManualsLINE ALONG APPROPRIATE DOTTEDANGLE OF THE SLOPE FOLDPage Product Quick Specs BELTS AND BLADES