Simplicity 5101604, 543777-0113-E1 Slope Operation, Thrown Objects, Moving Parts, Operator Safety

Page 5

Slope Operation

Operator Safety

Slope Operation

Operation on slopes can be dangerous. Using the unit on a slope that is too steep where you do not have adequate wheel traction (and control) can cause sliding, loss of steering, control, and possible rollover. You should not operate on a slope greater than a 5.4 foot rise over a 20 foot length (15 degrees).

Always mow across slopes, not up and down (to maintain traction on the wheels) and avoid sudden turns or rapid speed changes. Reduce speed and use extreme caution on ALL slopes.

Also, note that the surface condition you are on can greatly impact your ability to safely operate this machine. Operating on wet or slippery slopes can cause sliding and loss of steering and control. Do not operate on slopes that are slippery, wet, or have soft soil conditions.

If you feel unsure about operating the unit on a slope, don’t do it.

It’s not worth the risk.

Thrown Objects

This unit has spinning mower blades. These blades can pick up and throw debris that could seriously injure a bystander. Be sure to clean up the area to be mowed and remove objects that could be thrown by the blade BEFORE you start mowing.

Do not operate this unit without the entire grass catcher or discharge guard (deflector) in place.

Also, do not allow anyone in the area while the unit is running! If someone does enter the area, shut the unit off immediately until they leave

Moving Parts

This equipment has many moving parts that can injure you or someone else. However, if you stay in the operator zone (stay seated in the seat), and follow the safety rules in this operator’s manual, the unit is safe to operate.

The mower deck has spinning mower blades that can amputate hands and feet. Do not allow anyone near the unit while it is running! Keep safety devices (guards, shields, and switches) in place and working.

To help you, the operator, use this equipment safely, it is equipped with an operator-present safety system. Do NOT attempt to alter or bypass the system. See your dealer immediately if the system does not pass all the safety interlock system tests found in this manual.

3

Image 5

Contents Cobalt Series OPERATOR’S MANUAL30HP Zero-Turn Riders Mfg. NoDATE PURCHASED Operator Safety Table of ContentsFeatures & Controls Regular MaintenanceOperator Safety Operator SafetyOperating Safety Read the ManualMoving Parts Slope OperationThrown Objects Overhead Obstacles Roll Bar UseRetaining Walls, Drop-offs, and Water Enclosed Areas Fuel and MaintenanceTransporting and Storage General OperationEmissions Towed Equipment Ride-On UnitsIgnition System Operating on steep slopes can be dangerousSafe Handling of Gasoline Service and MaintenanceService & Maintenance Inspection of the Roll Bar Protective Structure Roll Bar InstructionsOperational Warnings INSPECT BUCKLE LATCH INSPECT WEBBING Inspection and Maintenance of the Roll Bar Seat Belt Safety DecalsOperational SAFETY Checks Safety Interlock SystemSafety Icons North American Safety IconsFeatures and Controls Features and ControlsIdentification Numbers CE ModelsPTO Power Take Off Switch Deck Lift Pedal, Cutting Height Adjustment Pin & Deck Lift Lock LeverControl Functions Parking BrakeHour Meter / Maintenance Reminder Ignition SwitchSeat Adjustment Lever Throttle ControlOperation General Operating SafetyOperation Checks Before StartingCheck Tire Pressures Seat AdjustmentPushing the Rider by Hand OperationFoot Pedal Adjustment Mowing Height AdjustmentTo Adjust Pedal Position Figure 5. Mowing Height Adjustment A. Cutting Height Adjustment Pin2. NOTE A warm engine may not require choking Starting the EngineStopping the Rider Basic Driving Zero-Turn Driving PracticeSmooth Travel Figure 7. Move Control Levers GraduallyPractice Turning Around a Corner Advanced DrivingFigure 10. Turning Around a Corner Figure 11. Turning in PlaceTo Lower the Roll Bar Raise and Lower the Roll BarTo Raise the Roll Bar StorageMowing Recommendations MowingHeight of Grass Figure 14. Proper Cutting HeightWhen and How Often to Mow Mowing MethodsNote Always operate the engine at full throttle when mowing How Much Grass to Cut Off When BroadcastingFigure 17. Trailer Weight Recommendations A. Clevis Pin B. Clip Attaching a TrailerProper Mulching Mulching Requires EXCELLENT Mowing ConditionsRegular Maintenance Regular MaintenanceMaintenance Schedule Safety ItemsFuel Filter Checking / Adding FuelChange Oil & Filter Inspect Muffler and Spark ArresterChange Hydraulic Oil Filter Check Hydraulic Oil LevelChange Interval Every 250 Hours Filter Part Number Figure 19. Checking Hydraulic Oil Level A. Hydraulic Oil ReservoirGrease LubricationLubricating the Front Casters Figure 21. Deck LubricationRemoving the Mower Blade Servicing The Mower BladesAvoid injury! Mower blades are sharp Inspecting the Mower BladesFigure 31. Tightening the Mower Blade for Installation Reinstalling the Mower BladesC. Mower Blade Air Lift Points Up For Installation Sharpening the Mower BladeBattery Maintenance Battery ChargingNOTE This unit is equipped with a maintenance-free BCIU1 battery Cleaning the Battery and CablesSpeed Balancing Adjustment Ground Speed Control Lever AdjustmentTo Adjust the Handle Alignment To Adjust the Handle PlacementReturn-to-Neutral Adjustment Neutral AdjustmentChecking the Adjustment Figure 35. Neutral Adjustment RH side shown A. Adjustment Linkage RodHydraulic Pump Drive Belt Replacement Parking Brake AdjustmentFigure 37. Parking Brake Adjustment A. Brake Spring B. Adjustment Nut Figure 38. Hydraulic Pump Drive Belt Replacement A. Pump Drive BeltTo adjust the spring pre-load Suspension AdjustmentSpring loaded components can kick back causing injury To adjust the upper mounting position Rear ShocksChecking the Deck Lift Rod Timing Adjustment Deck Lift Rod Timing Adjustment4. To adjust the inner lift rod Refer to Figure 9. To adjust the outer lift rod Refer to FigureDeck Lift Spring Deck Leveling AdjustmentRegular Maintenance NOTE Before adjusting the deck level, the deck lift rodFigure 46. Mower PTO Belt A. Idler Arm B. Stationary Idler Pulley Mower Belt ReplacementC. 1/2” Breaker Bar D. Spring Figure 47. Mower PTO Belt Routing A. Spindle Pulley B. PTO Drive BeltTroubleshooting TroubleshootingTroubleshooting the Rider PROBLEMTroubleshooting the Mower Troubleshooting the Rider continuedRider drive belt slips Brake will not holdStreaking Troubleshooting Common Cutting ProblemsScalping Stepped CuttingSpecifications SpecificationsDIMENSIONS Technical ManualsALONG APPROPRIATE DOTTED LINEANGLE OF THE SLOPE FOLDPage BELTS AND BLADES Product Quick Specs