Husqvarna 335FR manual Cutting equipment, Locking nut, General rules

Page 10

GENERAL SAFETY PRECAUTIONS

Locking nut

A locking nut is used to secure some types of cutting attachment.

When fitting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. To remove it, undo the nut in the same direction as the cutting attachment rotates. (CAUTION! The nut has a left-hand thread.) Tighten the nut using the socket spanner.

The nylon lining inside the locking nut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.5 Nm. The nut should be replaced after it has been put on approx. 10 times.

Cutting equipment

This section describes how to choose and maintain your cutting equipment in order to:

•Reduce the risk of blade thrust.

•Obtain maximum cutting performance.

•Extend the life of cutting equipment.

IMPORTANT!

Only use cutting attachments with the guards we recommend! See the chapter on Technical data.

Refer to the instructions for the cutting attachment to check the correct way to load the cord and the correct cord diameter.

Keep the teeth of the blade correctly sharpened! Follow our recommendations. Also refer to the instructions on the blade packaging.

Maintain the correct blade setting! Follow our instructions and use the recommended file gauge.

WARNING! Always stop the engine

! before doing any work on the cutting attachment.This continues to rotate even after the throttle has been released. Ensure that the cutting attachment has stopped completely and disconnect the HT lead from the spark plug before you start to work on it.

WARNING! Using an incorrect cutting

! attachment or an incorrectly sharpened blade increases the risk of blade thrust.

Cutting equipment

Saw blades are intended for cutting fibrous types of wood.

Grass blades and grass cutters are intended for cutting coarse grass.

A trimmer head is intended for trimming grass.

General rules

Only use cutting attachments with the guards we recommend! See the chapter on Technical data.

Keep the teeth of the blade correctly sharpened! Follow our instructions and use the recommended file gauge. An incorrectly sharpened or damaged blade increases the risk of accidents.

10 – English

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 333R 335FR 335RX-series Operator of the machine must Ensure, while working, that no KEY to SymbolsSymbols Persons or animals come closer thanContents Introduction Dear customerWhat is WHAT? What is what on the clearing saw?General Safety Precautions Personal protective equipmentMachine′s safety equipment Throttle lockoutVibration damping system Stop switchCutting attachment guard 335RX, 335FRMuffler Cutting equipment Cutting equipmentLocking nut General rulesSharpening grass cutters and grass blades Sharpening the saw bladeTrimmer head Assembling the handlebar and throttle AssemblyRX,FR R Assembling the cutting equipmentFitting a blade guard, grass blade and grass cutter Fitting the blade guard and saw bladeShielded by the blade guard when doing this. Always Fitting other guards and cutting attachmentsStandard harness Adjusting the harness and clearing sawTriobalance harness Correct balance Fuel Handling Fuel safetyFuel Fueling MixingStarting and stopping Starting and StoppingCheck before starting StartingStopping For throttle handles with a start throttle lockStarter cord around your hand General working instructions Basic safety rulesWorking Techniques ABC of clearingForestry clearing using a saw blade Brush cutting with a saw blade Grass clearing using a grass blade Grass trimming with a trimmer headMaintenance CarburetorLow speed jet L Fine adjustment of the idle speed TCorrectly adjusted carburetor High speed jet HAdjusting the start throttle speed MufflerBevel gear Cleaning the air filterCooling system Air filterSpark plug Maintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataApproved accessories Type Cutting attachment guard, Art. no Your Warranty Rights and Obligations Emission Warranty Parts List Page S35 2,7mm 095-.106 25 m 15 cm T35, T35x T45, T45x Auto Trimmy SII Page 1151115-95
Top Page Image Contents