Husqvarna 335FR manual Fitting other guards and cutting attachments

Page 15

ASSEMBLY

•Insert the locking pin (C) in the hole to lock the shaft.

•Place the blade (D) and support ﬂange (F) on the output shaft.

•Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

Fitting other guards and cutting attachments

•Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. CAUTION! Ensure that the guard extension is ﬁtted.

Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. See diagram.

L

• When loosening and tightening the saw blade nut,

there is a risk of injury from the teeth of the saw blade.

You should therefore always ensure that your hand is

shielded by the blade guard when doing this. Always

use a socket spanner with a shaft that is long enough

M

A

C

to allow this. The arrow in the diagram shows the area

where you should operate the socket spanner when

loosening or tightening the nut.

•Fit the drive disc (B) on the output shaft.

H

BA

C

ML

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation.

H

H

•To dismantle, follow the instructions in the reverse order.

English – 15

Image 15

Contents 333R 335FR 335RX-series Persons or animals come closer than KEY to SymbolsSymbols Operator of the machine must Ensure, while working, that noContents Dear customer IntroductionWhat is what on the clearing saw? What is WHAT?Personal protective equipment General Safety PrecautionsThrottle lockout Machine′s safety equipment335RX, 335FR Stop switchCutting attachment guard Vibration damping systemMufﬂer General rules Cutting equipmentLocking nut Cutting equipmentSharpening the saw blade Sharpening grass cutters and grass bladesTrimmer head Assembling the cutting equipment AssemblyRX,FR R Assembling the handlebar and throttleFitting the blade guard and saw blade Fitting a blade guard, grass blade and grass cutterFitting other guards and cutting attachments Shielded by the blade guard when doing this. AlwaysAdjusting the harness and clearing saw Standard harnessTriobalance harness Correct balance Fuel safety Fuel HandlingFuel Mixing FuelingStarting Starting and StoppingCheck before starting Starting and stoppingFor throttle handles with a start throttle lock StoppingStarter cord around your hand ABC of clearing Basic safety rulesWorking Techniques General working instructionsForestry clearing using a saw blade Brush cutting with a saw blade Grass trimming with a trimmer head Grass clearing using a grass bladeCarburetor MaintenanceHigh speed jet H Fine adjustment of the idle speed TCorrectly adjusted carburetor Low speed jet LMufﬂer Adjusting the start throttle speedAir ﬁlter Cleaning the air ﬁlterCooling system Bevel gearSpark plug Maintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataApproved accessories Type Cutting attachment guard, Art. no Your Warranty Rights and Obligations Emission Warranty Parts List Page S35 2,7mm 095-.106 25 m 15 cm T35, T35x T45, T45x Auto Trimmy SII Page 1151115-95