Snapper 500Z manual Features & Controls

Page 14

Controls

Features & Controls

Parking Brake

 

 

 

DISENGAGE

Releases the parking brake.

 

 

 

 

 

 

 

 

 

ENGAGE

Locks the parking brake.

 

 

 

 

 

 

 

 

 

Pull the parking brake lever up to engage the parking brake. Push the lever down to disengage the parking brake. NOTE: To start the unit the parking brake must be engaged.

PTO (Power Take Off) Switch

The PTO switch engages and disengages the mower. Pull UP on the switch to engage, and push DOWN to disengage.

Deck Lift Pedal, Cutting Height

Adjustment Pin & Deck Lift Lock

Lever

These control the cutting height of the mower deck. Depress the pedal until it locks into the 4-1/2” (11,47 cm) position. Place the adjustment pin in the desired cutting height and release the lift lock lever.

Throttle Control

The throttle controls engine speed. Move the throttle forward to increase engine speed and back to decrease engine speed. Always operate at FULL throttle.

Choke

Close the choke for cold starting. Open the choke once the engine starts. A warm engine may not require choking. Pull the knob UP to close the choke. Push to knob DOWN to open the choke.

Hour Meter / Maintenance Reminder

Measures the time of the PTO being engaged. The hour meter measures the number of hours the PTO has been engaged. The hour meter will flash an initial oil change indicator at 5 hours, and a lubrication reminder every 50 hours. These reminders display for approximately two hours and will automatically reset themselves.

Note: The hour meter will register the passage of time only when the PTO is engaged. The hour meter has a self contained power source so the total hours are always visible.

Fuel Tank Cap

To remove the cap, turn counterclockwise.

Fuel Level Gauge

Displays the fuel level in the tank.

Transmission Oil Fill

This unit is equipped with two transmission oil reservoirs. The transmission oil reservoirs are located beneath the operator’s seat and in front of the engine. Transmission oil is added through the transmission oil reservoirs. It also serves as extra holding capacity as the transmissions heat up and the oil expands. See CHECK TRANSMISSION OIL LEVEL for oil level check and fill procedures.

12

www.Snapper.com

Page 13 Page 15
Image 14
Page 13 Page 15
Contents ZERO-TURN Riding Mower 26HP Zero-Turn RidersDate Purchased Table of Contents Operating Safety Operator SafetyOperator Safety Read the ManualMoving Parts Slope OperationThrown Objects Enclosed Areas Fuel and MaintenanceRetaining WALLS, DROP-OFFS, and Water Transporting and Storage Wear hearing protection when operating this machineGeneral Operation Ignition System Towed Equipment RIDE-ON UnitsEmissions Mow across slopes, not up and downSafe Handling of Gasoline Service and MaintenanceService & Maintenance Safety Decals Safety Icons Safety Interlock SystemOperational Safety Checks North American Safety IconsIdentification Numbers Features and ControlsFeatures and Controls Control Functions Seat Adjustment LeverIgnition Switch Ground Speed Control LeversFeatures & Controls Operation General Operating SafetyOperation Checks Before StartingTire Pressure Seat AdjustmentCheck Tire Pressures To adjust pedal position Mowing Height AdjustmentFoot Pedal Adjustment Stopping the Rider Insert the key into the ignition switch and turn it toStarting the Engine Pushing the Rider By HandForward Reverse Travel Zero Turn Driving PracticeForward Travel Practice Executing an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place Executing TurnsHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Methods Mulching Requires Excellent Mowing Conditions Attaching a TrailerProper Mulching Engine Speed & Ground Speed for MulchingMaintenance Schedule Regular MaintenanceRegular Maintenance Safety Items Before Every SpringFuel Filter Engine MaintenanceChecking / Adding Fuel Change Oil & FilterOil LubricationGrease Lubricating the Front CastersTransmission Oil Filter Change Change Interval Every 200 Hours Replacement Filter NumberCheck / Fill Transmission Oil Never weld or straighten bent mower blades Servicing The Mower BladesInspecting the Mower Blades Reinstalling the Mower Blades Balancing the Mower Blade NailNeutral Adjustment Ground Speed Control Lever AdjustmentSpeed Balancing Adjustment Parking Brake Adjustment 375 0,95 cmReturn-to-Neutral Adjustment Return-to-Neutral Adjustment Jam Nuts Neutral Return RodAdjustment is required continue with Step Deck Rod Timing AdjustmentDeck Leveling Adjustment Mower deckMower Belt Replacement 48 Deck Models To avoid damaging belts, do not PRY Belts Over PulleysHydraulic Pump Drive Belt Replacement Use extreme caution when removing this springBattery Maintenance Battery CompartmentCharging a Completely Discharged Battery Battery ServiceChecking Battery Voltage Jump Starting With Auxiliary Booster BatteryMake Certain Vehicles do not Touch Temporary Storage 30 Days Or Less StorageStarting After Long Term Storage Long Term Storage Longer Than 30 DaysTroubleshooting Chart TroubleshootingTroubleshooting Troubleshooting the RiderTroubleshooting Troubleshooting Common Cutting Problems StreakingEngine SpecificationsDimensions ChassisSlope LineIndentification Surface Vertical a with Edge this AlignPage Page Page Tractor Product SpecificationsCommon Service Parts Mower Deck

500Z specifications

The Snapper 500Z is a cutting-edge zero-turn lawn mower designed for both residential and commercial landscaping needs. This mower offers exceptional performance, versatility, and ease of use, making it a top choice for lawn care enthusiasts and professionals alike.

One of the main features of the Snapper 500Z is its powerful engine. Equipped with a reliable 23-horsepower Briggs & Stratton engine, the 500Z provides ample power to tackle challenging mowing tasks. This engine is designed to deliver smooth and consistent performance, ensuring that users can navigate their lawns with ease.

The Snapper 500Z also boasts a robust 52-inch cutting deck, made from durable materials that can withstand the rigors of regular use. With its wide cutting path, this mower allows users to cover more ground in less time, making mowing tasks quicker and more efficient. The adjustable cutting height feature provides users with the flexibility to customize their mowing height, ranging from 1.5 to 4.5 inches, ensuring a tailored cut for every lawn type.

Technology-driven features set the Snapper 500Z apart from its competitors. The mower is equipped with a hydrostatic transmission system, providing effortless control and smooth acceleration. Users can easily adjust their speed without the hassle of shifting gears, allowing for a seamless mowing experience. This system enhances mobility and maneuverability, enabling users to navigate around obstacles with precision.

Comfort and ergonomics are also a priority in the design of the Snapper 500Z. The mower features a plush, high-back seat with armrests, offering support during longer mowing sessions. An intuitive control layout ensures users can easily access all necessary functions without distraction. Additionally, the mower's compact design allows for easy storage and transportation.

Safety is paramount, and the Snapper 500Z incorporates various safety features. The operator presence control system ensures that the mower will not operate unless the user is seated, reducing the risk of accidents. Additionally, the durable roll-over protection structure (ROPS) provides an added layer of safety during operation.

In conclusion, the Snapper 500Z combines powerful performance, advanced technology, and user-friendly design to create an exceptional mowing experience. With its reliable engine, versatile cutting deck, and comfort-focused features, the Snapper 500Z is a standout choice for anyone looking to maintain a pristine lawn.
Top Page Image Contents