Snapper Belt Diagrams: 48 and 52 Inch Deck Maintenance
Page 34

Maintenance

Regular Maintenance

Mower Belt Replacement - 48” Deck Models

NOTICE

To avoid damaging belts, DO NOT PRY BELTS OVER PULLEYS.

1.Park the tractor on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key.

2.Lower the mower deck to its lowest cutting position and remove the mower deck guards.

3.Using a 1/2” breaker bar, place the square end in the square hole located in the end of the idler arm (A, Figures 40). Carefully rotate the breaker bar CLOCKWISE, which will relieve the tension on the belt exerted from the idler arm.

WARNING

Use extreme caution when rotating the idler arm with the breaker bar, due to the increased tension in the spring as the idler arm is being rotated. Injury may result if the breaker bar is prematurely released while the spring is under tension.

4.Slide the drive belt over the edge of the stationary idler pulley (B). Carefully release the tension on the breaker bar.

5.Remove the old belt and replace with a new one. Make sure the V-side of the belt runs in the pulley grooves (Figure 41).

6.Install the drive belt on the PTO pulley, the spindle pulleys and all idler pulleys except the stationary pulley (B, Figure 40). Carefully rotate the breaker bar CLOCKWISE and install the belt on the stationary idler pulley (B). Carefully release the tension on the breaker bar.

7.Reinstall the mower deck guards.

8.Run the mower under no-load condition for about 5 minutes to break-in the new belt.

Figure 40. Mower PTO Belt

A.Idler Arm

B.Stationary Idler Pulley

D

 

B

C

A

 

 

A

 

 

 

 

D

A

 

 

 

 

Figure 41. Mower PTO Belt Routing

A.Spindle Pulley

B.PTO Drive Belt

C.Spring-loaded Idler Pulley

D.Stationary Idler Pulley

32

www.Snapper.com

Page 33 Page 35
Image 34
Page 33 Page 35
Contents ZERO-TURN Riding Mower 26HP Zero-Turn RidersDate Purchased Table of Contents Operating Safety Operator SafetyOperator Safety Read the ManualThrown Objects Slope OperationMoving Parts Retaining WALLS, DROP-OFFS, and Water Fuel and MaintenanceEnclosed Areas General Operation Wear hearing protection when operating this machineTransporting and Storage Ignition System Towed Equipment RIDE-ON UnitsEmissions Mow across slopes, not up and downService & Maintenance Service and MaintenanceSafe Handling of Gasoline Safety Decals Safety Icons Safety Interlock SystemOperational Safety Checks North American Safety IconsFeatures and Controls Features and ControlsIdentification Numbers Control Functions Seat Adjustment LeverIgnition Switch Ground Speed Control LeversFeatures & Controls Operation General Operating SafetyOperation Checks Before StartingCheck Tire Pressures Seat AdjustmentTire Pressure Foot Pedal Adjustment Mowing Height AdjustmentTo adjust pedal position Stopping the Rider Insert the key into the ignition switch and turn it toStarting the Engine Pushing the Rider By HandForward Travel Practice Zero Turn Driving PracticeForward Reverse Travel Executing an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place Executing TurnsHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Methods Mulching Requires Excellent Mowing Conditions Attaching a TrailerProper Mulching Engine Speed & Ground Speed for MulchingMaintenance Schedule Regular MaintenanceRegular Maintenance Safety Items Before Every SpringFuel Filter Engine MaintenanceChecking / Adding Fuel Change Oil & FilterOil LubricationGrease Lubricating the Front CastersCheck / Fill Transmission Oil Change Interval Every 200 Hours Replacement Filter NumberTransmission Oil Filter Change Inspecting the Mower Blades Servicing The Mower BladesNever weld or straighten bent mower blades Reinstalling the Mower Blades Balancing the Mower Blade NailSpeed Balancing Adjustment Ground Speed Control Lever AdjustmentNeutral Adjustment Parking Brake Adjustment 375 0,95 cmReturn-to-Neutral Adjustment Return-to-Neutral Adjustment Jam Nuts Neutral Return RodAdjustment is required continue with Step Deck Rod Timing AdjustmentDeck Leveling Adjustment Mower deckMower Belt Replacement 48 Deck Models To avoid damaging belts, do not PRY Belts Over PulleysHydraulic Pump Drive Belt Replacement Use extreme caution when removing this springBattery Maintenance Battery CompartmentCharging a Completely Discharged Battery Battery ServiceChecking Battery Voltage Jump Starting With Auxiliary Booster BatteryMake Certain Vehicles do not Touch Temporary Storage 30 Days Or Less StorageStarting After Long Term Storage Long Term Storage Longer Than 30 DaysTroubleshooting Chart TroubleshootingTroubleshooting Troubleshooting the RiderTroubleshooting Troubleshooting Common Cutting Problems StreakingEngine SpecificationsDimensions ChassisSlope LineIndentification Surface Vertical a with Edge this AlignPage Page Page Tractor Product SpecificationsCommon Service Parts Mower Deck

500Z specifications

The Snapper 500Z is a cutting-edge zero-turn lawn mower designed for both residential and commercial landscaping needs. This mower offers exceptional performance, versatility, and ease of use, making it a top choice for lawn care enthusiasts and professionals alike.

One of the main features of the Snapper 500Z is its powerful engine. Equipped with a reliable 23-horsepower Briggs & Stratton engine, the 500Z provides ample power to tackle challenging mowing tasks. This engine is designed to deliver smooth and consistent performance, ensuring that users can navigate their lawns with ease.

The Snapper 500Z also boasts a robust 52-inch cutting deck, made from durable materials that can withstand the rigors of regular use. With its wide cutting path, this mower allows users to cover more ground in less time, making mowing tasks quicker and more efficient. The adjustable cutting height feature provides users with the flexibility to customize their mowing height, ranging from 1.5 to 4.5 inches, ensuring a tailored cut for every lawn type.

Technology-driven features set the Snapper 500Z apart from its competitors. The mower is equipped with a hydrostatic transmission system, providing effortless control and smooth acceleration. Users can easily adjust their speed without the hassle of shifting gears, allowing for a seamless mowing experience. This system enhances mobility and maneuverability, enabling users to navigate around obstacles with precision.

Comfort and ergonomics are also a priority in the design of the Snapper 500Z. The mower features a plush, high-back seat with armrests, offering support during longer mowing sessions. An intuitive control layout ensures users can easily access all necessary functions without distraction. Additionally, the mower's compact design allows for easy storage and transportation.

Safety is paramount, and the Snapper 500Z incorporates various safety features. The operator presence control system ensures that the mower will not operate unless the user is seated, reducing the risk of accidents. Additionally, the durable roll-over protection structure (ROPS) provides an added layer of safety during operation.

In conclusion, the Snapper 500Z combines powerful performance, advanced technology, and user-friendly design to create an exceptional mowing experience. With its reliable engine, versatile cutting deck, and comfort-focused features, the Snapper 500Z is a standout choice for anyone looking to maintain a pristine lawn.
Top Page Image Contents