Snapper 500Z Hydraulic Pump Drive Belt Replacement, Use extreme caution when removing this spring

Page 35

Hydraulic Pump Drive Belt Replacement

1.Park the tractor on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key.

2.Remove the PTO drive belt (see MOWER BELT REPLACEMENT for removal instructions).

3.Loosen and remove the crankshaft bolt (C, Figure 42) and the PTO clutch (B) from the engine crankshaft.

WARNING

STORED ENERGY DEVICE: Improper release of the belt tension spring can result in personal injury.

Use extreme caution when removing this spring.

4.Loosen the nut on the spring anchor eyebolt (G, Figure 43) to release the majority of the belt tension. Use caution and remove the nut to completely release the tension.

A

B

C

Figure 42. Removing the PTO Clutch

A.PTO Clutch Mounting Tab

B.PTO Clutch

C.Crankshaft Bolt

Regular Maintenance

5.Remove the old belt and replace it with the new one. Make sure the V-side of the belt runs in the grooves of the crankshaft pulley and the transmission pulleys (B & C).

6.Reinstall the spring anchor eyebolt (G) into the anchor tab and loosely fasten the nut. Adjust the anchor eyebolt until a measurement of 5-7/8” (14,92 cm) is achieved from the outside if the spring hooks. Tighten nut.

7.Reinstall the PTO clutch to the engine crankshaft and secure with the crankshaft bolt. Tighten the crankshaft bolt to 65 ft. lbs (88 Nm).

NOTE: Make sure that the slot in the PTO clutch lines up with the PTO clutch mounting tab (A, Figure 42) underneath the engine deck.

8. Reinstall the PTO drive belt.

 

B

 

H

E

D

 

A

C

C

 

F

 

G

5-7/8”

 

(14.92 cm)

 

Figure 43. Hydraulic Pump Drive Belt Replacement

A.Pump Drive Belt

B.Crankshaft Pulley

C.Pump Pulley

D.Idler Pulley

E.Idler Arm

F.Spring

G.Spring Anchor Eyebolt

H.Stationary Idler Pulley

Maintenance

33

Page 34 Page 36
Image 35
Page 34 Page 36
Contents 26HP Zero-Turn Riders ZERO-TURN Riding MowerDate Purchased Table of Contents Read the Manual Operator SafetyOperator Safety Operating SafetyMoving Parts Slope OperationThrown Objects Enclosed Areas Fuel and MaintenanceRetaining WALLS, DROP-OFFS, and Water Transporting and Storage Wear hearing protection when operating this machineGeneral Operation Mow across slopes, not up and down Towed Equipment RIDE-ON UnitsEmissions Ignition SystemSafe Handling of Gasoline Service and MaintenanceService & Maintenance Safety Decals North American Safety Icons Safety Interlock SystemOperational Safety Checks Safety IconsIdentification Numbers Features and ControlsFeatures and Controls Ground Speed Control Levers Seat Adjustment LeverIgnition Switch Control FunctionsFeatures & Controls Checks Before Starting General Operating SafetyOperation OperationTire Pressure Seat AdjustmentCheck Tire Pressures To adjust pedal position Mowing Height AdjustmentFoot Pedal Adjustment Pushing the Rider By Hand Insert the key into the ignition switch and turn it toStarting the Engine Stopping the RiderForward Reverse Travel Zero Turn Driving PracticeForward Travel Practice Executing Turns Practice Turning Around a CornerPractice Turning In Place Executing an End-Of-Row Zero TurnTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassMowing Methods Engine Speed & Ground Speed for Mulching Attaching a TrailerProper Mulching Mulching Requires Excellent Mowing ConditionsSafety Items Before Every Spring Regular MaintenanceRegular Maintenance Maintenance ScheduleChange Oil & Filter Engine MaintenanceChecking / Adding Fuel Fuel FilterLubricating the Front Casters LubricationGrease OilTransmission Oil Filter Change Change Interval Every 200 Hours Replacement Filter NumberCheck / Fill Transmission Oil Never weld or straighten bent mower blades Servicing The Mower BladesInspecting the Mower Blades Balancing the Mower Blade Nail Reinstalling the Mower BladesNeutral Adjustment Ground Speed Control Lever AdjustmentSpeed Balancing Adjustment 375 0,95 cm Parking Brake AdjustmentReturn-to-Neutral Adjustment Jam Nuts Neutral Return Rod Return-to-Neutral AdjustmentMower deck Deck Rod Timing AdjustmentDeck Leveling Adjustment Adjustment is required continue with StepTo avoid damaging belts, do not PRY Belts Over Pulleys Mower Belt Replacement 48 Deck ModelsUse extreme caution when removing this spring Hydraulic Pump Drive Belt ReplacementBattery Compartment Battery MaintenanceJump Starting With Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Charging a Completely Discharged BatteryMake Certain Vehicles do not Touch Long Term Storage Longer Than 30 Days StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessTroubleshooting the Rider TroubleshootingTroubleshooting Troubleshooting ChartTroubleshooting Streaking Troubleshooting Common Cutting ProblemsChassis SpecificationsDimensions EngineSurface Vertical a with Edge this Align LineIndentification SlopePage Page Page Mower Deck Product SpecificationsCommon Service Parts Tractor

500Z specifications

The Snapper 500Z is a cutting-edge zero-turn lawn mower designed for both residential and commercial landscaping needs. This mower offers exceptional performance, versatility, and ease of use, making it a top choice for lawn care enthusiasts and professionals alike.

One of the main features of the Snapper 500Z is its powerful engine. Equipped with a reliable 23-horsepower Briggs & Stratton engine, the 500Z provides ample power to tackle challenging mowing tasks. This engine is designed to deliver smooth and consistent performance, ensuring that users can navigate their lawns with ease.

The Snapper 500Z also boasts a robust 52-inch cutting deck, made from durable materials that can withstand the rigors of regular use. With its wide cutting path, this mower allows users to cover more ground in less time, making mowing tasks quicker and more efficient. The adjustable cutting height feature provides users with the flexibility to customize their mowing height, ranging from 1.5 to 4.5 inches, ensuring a tailored cut for every lawn type.

Technology-driven features set the Snapper 500Z apart from its competitors. The mower is equipped with a hydrostatic transmission system, providing effortless control and smooth acceleration. Users can easily adjust their speed without the hassle of shifting gears, allowing for a seamless mowing experience. This system enhances mobility and maneuverability, enabling users to navigate around obstacles with precision.

Comfort and ergonomics are also a priority in the design of the Snapper 500Z. The mower features a plush, high-back seat with armrests, offering support during longer mowing sessions. An intuitive control layout ensures users can easily access all necessary functions without distraction. Additionally, the mower's compact design allows for easy storage and transportation.

Safety is paramount, and the Snapper 500Z incorporates various safety features. The operator presence control system ensures that the mower will not operate unless the user is seated, reducing the risk of accidents. Additionally, the durable roll-over protection structure (ROPS) provides an added layer of safety during operation.

In conclusion, the Snapper 500Z combines powerful performance, advanced technology, and user-friendly design to create an exceptional mowing experience. With its reliable engine, versatile cutting deck, and comfort-focused features, the Snapper 500Z is a standout choice for anyone looking to maintain a pristine lawn.
Top Page Image Contents