Snapper 500Z manual Check / Fill Transmission Oil, Transmission Oil Filter Change

Page 27

Check / Fill Transmission Oil

Oil Type: 20W-50 conventional detergent motor oil.

1.Check the oil level when the unit is cold. Locate the transmission oil reservoirs (A, Figure 24) located on the seat support plate. The oil should be up to the “FULL COLD” mark (B). If the oil is below this level, proceed to step 2.

2.Before removing the reservoir caps, make sure the area around the reservoir cap and fill neck of the reservoir is free of dust, dirt, or other debris. Remove the reservoir cap.

3.Add oil up to the “FULL COLD” mark (B).

4.Reinstall the reservoir caps.

Transmission Oil Filter Change

Change Interval: Every 200 Hours

Replacement Filter Number: 5101026X1

1.Locate the transmission oil filters (A, Figure 25) underneath the rear of the machine on the transmissions.

2.Remove the three 1/4” filter guard screws (C) and the filter guard (B).

3.Clean the area around the filter base and remove the filter.

4.Apply a film of new oil to the gasket of the new replacement filter. After the oil has drained, thread the new filter onto the filter base until the gasket makes contact, then tighten 3/4 of a turn more.

5.Reinstall the filter guard with the three 1/4” filter guard screws

6.Using a hex bit swivel socket or a modified allen wrench remove the top port plug from the transmissions.

7.Remove the transmission reservoir cap and fill with oil until oil appears at the bottom of the transmission’s top port (approximately 2 qts (1,89L).

8.Reinstall the top port plug and tighten to 15 ft lbs (20,38 Nm).

9.Continue to add oil to the transmission oil reservoirs until the oil level reaches the “FULL COLD” mark. Reinstall the oil reservoir cap.

10.Repeat this process for the other side of the machine.

11.Run the unit for several minutes and check the transmission oil level.

IMPORTANT NOTE: Use caution after changing the filter; air in the hydraulic system may affect the responsiveness of the ground speed control levers. Repeat step 11 until the air is out of the system.

Regular Maintenance

A

B

Figure 24. Checking Transmission Oil Level

A.Transmission Oil Reservoirs

B.“FULL COLD” mark

A

B

D

C

Figure 25. Transmission (Left Side Shown.)

A.Transmission Oil Filter

B.Filter Guard

C.1/4” Filter Guard Screws

D.Top Port Plug

Maintenance

25

Image 27
Contents 26HP Zero-Turn Riders ZERO-TURN Riding MowerDate Purchased Table of Contents Read the Manual Operator SafetyOperator Safety Operating SafetySlope Operation Thrown ObjectsMoving Parts Fuel and Maintenance Retaining WALLS, DROP-OFFS, and WaterEnclosed Areas Wear hearing protection when operating this machine General OperationTransporting and Storage Mow across slopes, not up and down Towed Equipment RIDE-ON UnitsEmissions Ignition SystemService and Maintenance Service & MaintenanceSafe Handling of Gasoline Safety Decals North American Safety Icons Safety Interlock SystemOperational Safety Checks Safety IconsFeatures and Controls Features and ControlsIdentification Numbers Ground Speed Control Levers Seat Adjustment LeverIgnition Switch Control FunctionsFeatures & Controls Checks Before Starting General Operating SafetyOperation OperationSeat Adjustment Check Tire PressuresTire Pressure Mowing Height Adjustment Foot Pedal AdjustmentTo adjust pedal position Pushing the Rider By Hand Insert the key into the ignition switch and turn it toStarting the Engine Stopping the RiderZero Turn Driving Practice Forward Travel PracticeForward Reverse Travel Executing Turns Practice Turning Around a CornerPractice Turning In Place Executing an End-Of-Row Zero TurnTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassMowing Methods Engine Speed & Ground Speed for Mulching Attaching a TrailerProper Mulching Mulching Requires Excellent Mowing ConditionsSafety Items Before Every Spring Regular MaintenanceRegular Maintenance Maintenance ScheduleChange Oil & Filter Engine MaintenanceChecking / Adding Fuel Fuel FilterLubricating the Front Casters LubricationGrease OilChange Interval Every 200 Hours Replacement Filter Number Check / Fill Transmission OilTransmission Oil Filter Change Servicing The Mower Blades Inspecting the Mower BladesNever weld or straighten bent mower blades Balancing the Mower Blade Nail Reinstalling the Mower BladesGround Speed Control Lever Adjustment Speed Balancing AdjustmentNeutral Adjustment 375 0,95 cm Parking Brake AdjustmentReturn-to-Neutral Adjustment Jam Nuts Neutral Return Rod Return-to-Neutral AdjustmentMower deck Deck Rod Timing AdjustmentDeck Leveling Adjustment Adjustment is required continue with StepTo avoid damaging belts, do not PRY Belts Over Pulleys Mower Belt Replacement 48 Deck ModelsUse extreme caution when removing this spring Hydraulic Pump Drive Belt ReplacementBattery Compartment Battery MaintenanceJump Starting With Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Charging a Completely Discharged BatteryMake Certain Vehicles do not Touch Long Term Storage Longer Than 30 Days StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessTroubleshooting the Rider TroubleshootingTroubleshooting Troubleshooting ChartTroubleshooting Streaking Troubleshooting Common Cutting ProblemsChassis SpecificationsDimensions EngineSurface Vertical a with Edge this Align LineIndentification SlopePage Page Page Mower Deck Product SpecificationsCommon Service Parts Tractor

500Z specifications

The Snapper 500Z is a cutting-edge zero-turn lawn mower designed for both residential and commercial landscaping needs. This mower offers exceptional performance, versatility, and ease of use, making it a top choice for lawn care enthusiasts and professionals alike.

One of the main features of the Snapper 500Z is its powerful engine. Equipped with a reliable 23-horsepower Briggs & Stratton engine, the 500Z provides ample power to tackle challenging mowing tasks. This engine is designed to deliver smooth and consistent performance, ensuring that users can navigate their lawns with ease.

The Snapper 500Z also boasts a robust 52-inch cutting deck, made from durable materials that can withstand the rigors of regular use. With its wide cutting path, this mower allows users to cover more ground in less time, making mowing tasks quicker and more efficient. The adjustable cutting height feature provides users with the flexibility to customize their mowing height, ranging from 1.5 to 4.5 inches, ensuring a tailored cut for every lawn type.

Technology-driven features set the Snapper 500Z apart from its competitors. The mower is equipped with a hydrostatic transmission system, providing effortless control and smooth acceleration. Users can easily adjust their speed without the hassle of shifting gears, allowing for a seamless mowing experience. This system enhances mobility and maneuverability, enabling users to navigate around obstacles with precision.

Comfort and ergonomics are also a priority in the design of the Snapper 500Z. The mower features a plush, high-back seat with armrests, offering support during longer mowing sessions. An intuitive control layout ensures users can easily access all necessary functions without distraction. Additionally, the mower's compact design allows for easy storage and transportation.

Safety is paramount, and the Snapper 500Z incorporates various safety features. The operator presence control system ensures that the mower will not operate unless the user is seated, reducing the risk of accidents. Additionally, the durable roll-over protection structure (ROPS) provides an added layer of safety during operation.

In conclusion, the Snapper 500Z combines powerful performance, advanced technology, and user-friendly design to create an exceptional mowing experience. With its reliable engine, versatile cutting deck, and comfort-focused features, the Snapper 500Z is a standout choice for anyone looking to maintain a pristine lawn.