Snapper 500Z manual Starting the Engine, Stopping the Rider, Pushing the Rider By Hand

Page 18

Operation

Operation

Starting the Engine

WARNING

If you do not understand how a specific control functions, or have not yet thoroughly read the FEATURES & CONTROLS section, do so now.

Do NOT attempt to operate the tractor without first becoming familiar with the location and function of ALL controls.

1.While sitting in the operator’s seat, engage the parking brake by pulling the parking brake lever up, make sure the PTO switch is disengaged (pressed down fully) and the ground speed control levers are locked in the NEUTRAL position.

2.NOTE: A warm engine may not require choking.

Set the engine throttle control to FULL throttle position. Then fully close the choke by pulling the knob OUT fully.

3.Insert the key into the ignition switch and turn it to

START.

4.After the engine starts, gradually open the choke (push knob down fully). Reduce to half throttle speed and allow to warm up.

Warm up the engine by running it for at least a minute before engaging the PTO switch or driving the rider.

5.After warming the engine, ALWAYS operate the unit at FULL THROTTLE when mowing.

In the event of an emergency the engine can be stopped by simply turning the ignition switch to STOP. Use this method only in emergency situations. For normal engine shut down follow the procedure given in STOPPING THE RIDER.

Stopping the Rider

1.Returning the ground speed control levers to the middle position will stop rider movement. Pivot the levers outward and lock them in NEUTRAL.

2.Disengage the PTO by pushing down on the PTO switch.

3.Engage the parking brake by pulling the handle up until it locks into position.

4.Move the throttle control to mid-throttle position and turn the ignition key to OFF. Remove the key.

Pushing the Rider By Hand

NOTICE

DO NOT TOW RIDER

Towing the units will cause transmission damage. Do not use another vehicle to push or pull this unit.

1.Disengage the PTO, engage the parking brake, turn the ignition OFF, and remove the key.

2.Locate the transmission release levers (A, Figure 8) located underneath the front of the fuel tanks.

3.Pull both transmission release levers back and down so that they lock in the disengaged (free-wheel position)

(C).

4.Disengage the parking brake.

The tractor can now be pushed by hand.

5.After moving the tractor, re-engage the transmissions by pulling the transmission release levers up and pushing them forward to the engaged (drive) position (B).

 

A

B

C

Figure 8. Transmission Release Levers (LH shown)

A.Transmission Release Lever

B.Engaged Position (Drive Position)

C.Disengaged Position (Free-wheel Position)

16

www.Snapper.com

Image 18
Contents ZERO-TURN Riding Mower 26HP Zero-Turn RidersDate Purchased Table of Contents Operating Safety Operator SafetyOperator Safety Read the ManualSlope Operation Thrown ObjectsMoving Parts Fuel and Maintenance Retaining WALLS, DROP-OFFS, and WaterEnclosed Areas Wear hearing protection when operating this machine General OperationTransporting and Storage Ignition System Towed Equipment RIDE-ON UnitsEmissions Mow across slopes, not up and downService and Maintenance Service & MaintenanceSafe Handling of Gasoline Safety Decals Safety Icons Safety Interlock SystemOperational Safety Checks North American Safety IconsFeatures and Controls Features and ControlsIdentification Numbers Control Functions Seat Adjustment LeverIgnition Switch Ground Speed Control LeversFeatures & Controls Operation General Operating SafetyOperation Checks Before StartingSeat Adjustment Check Tire PressuresTire Pressure Mowing Height Adjustment Foot Pedal AdjustmentTo adjust pedal position Stopping the Rider Insert the key into the ignition switch and turn it toStarting the Engine Pushing the Rider By HandZero Turn Driving Practice Forward Travel PracticeForward Reverse Travel Executing an End-Of-Row Zero Turn Practice Turning Around a CornerPractice Turning In Place Executing TurnsHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Methods Mulching Requires Excellent Mowing Conditions Attaching a TrailerProper Mulching Engine Speed & Ground Speed for MulchingMaintenance Schedule Regular MaintenanceRegular Maintenance Safety Items Before Every SpringFuel Filter Engine MaintenanceChecking / Adding Fuel Change Oil & FilterOil LubricationGrease Lubricating the Front CastersChange Interval Every 200 Hours Replacement Filter Number Check / Fill Transmission OilTransmission Oil Filter Change Servicing The Mower Blades Inspecting the Mower BladesNever weld or straighten bent mower blades Reinstalling the Mower Blades Balancing the Mower Blade NailGround Speed Control Lever Adjustment Speed Balancing AdjustmentNeutral Adjustment Parking Brake Adjustment 375 0,95 cmReturn-to-Neutral Adjustment Return-to-Neutral Adjustment Jam Nuts Neutral Return RodAdjustment is required continue with Step Deck Rod Timing AdjustmentDeck Leveling Adjustment Mower deckMower Belt Replacement 48 Deck Models To avoid damaging belts, do not PRY Belts Over PulleysHydraulic Pump Drive Belt Replacement Use extreme caution when removing this springBattery Maintenance Battery CompartmentCharging a Completely Discharged Battery Battery ServiceChecking Battery Voltage Jump Starting With Auxiliary Booster BatteryMake Certain Vehicles do not Touch Temporary Storage 30 Days Or Less StorageStarting After Long Term Storage Long Term Storage Longer Than 30 DaysTroubleshooting Chart TroubleshootingTroubleshooting Troubleshooting the RiderTroubleshooting Troubleshooting Common Cutting Problems StreakingEngine SpecificationsDimensions ChassisSlope LineIndentification Surface Vertical a with Edge this AlignPage Page Page Tractor Product SpecificationsCommon Service Parts Mower Deck

500Z specifications

The Snapper 500Z is a cutting-edge zero-turn lawn mower designed for both residential and commercial landscaping needs. This mower offers exceptional performance, versatility, and ease of use, making it a top choice for lawn care enthusiasts and professionals alike.

One of the main features of the Snapper 500Z is its powerful engine. Equipped with a reliable 23-horsepower Briggs & Stratton engine, the 500Z provides ample power to tackle challenging mowing tasks. This engine is designed to deliver smooth and consistent performance, ensuring that users can navigate their lawns with ease.

The Snapper 500Z also boasts a robust 52-inch cutting deck, made from durable materials that can withstand the rigors of regular use. With its wide cutting path, this mower allows users to cover more ground in less time, making mowing tasks quicker and more efficient. The adjustable cutting height feature provides users with the flexibility to customize their mowing height, ranging from 1.5 to 4.5 inches, ensuring a tailored cut for every lawn type.

Technology-driven features set the Snapper 500Z apart from its competitors. The mower is equipped with a hydrostatic transmission system, providing effortless control and smooth acceleration. Users can easily adjust their speed without the hassle of shifting gears, allowing for a seamless mowing experience. This system enhances mobility and maneuverability, enabling users to navigate around obstacles with precision.

Comfort and ergonomics are also a priority in the design of the Snapper 500Z. The mower features a plush, high-back seat with armrests, offering support during longer mowing sessions. An intuitive control layout ensures users can easily access all necessary functions without distraction. Additionally, the mower's compact design allows for easy storage and transportation.

Safety is paramount, and the Snapper 500Z incorporates various safety features. The operator presence control system ensures that the mower will not operate unless the user is seated, reducing the risk of accidents. Additionally, the durable roll-over protection structure (ROPS) provides an added layer of safety during operation.

In conclusion, the Snapper 500Z combines powerful performance, advanced technology, and user-friendly design to create an exceptional mowing experience. With its reliable engine, versatile cutting deck, and comfort-focused features, the Snapper 500Z is a standout choice for anyone looking to maintain a pristine lawn.