Snapper 500Z manual Specifications, Engine, Chassis, Transmissions, Dimensions

Page 43

Specifications

Specifications

NOTE: Specifications are correct at time of printing and are subject to change without notice.

ENGINE:

26 HP Briggs & Stratton

Make

Briggs & Stratton

Model

44P777-0124-G1

Horsepower

26 @ 3600 rpm

Displacement

44.2 Cu. in (724 cc)

Electrical System

12 Volt Starter, 16 amp. Alternator,

 

Battery: 340 CCA

Oil Capacity

2.0 US qt.. (1.9 L) w/ Filter

CHASSIS:

Fuel Tank

Capacity: 8 Gallons (30,3 L)

Rear Wheels

Tire Size: 20 x 8.00

-10 (48” Model)

 

Inflation Pressure: 15 psi (1,03 bar)

Front Wheels

Tire Size: 11 x 4.00

- 5

 

Inflation Pressure: 40 psi (2,76 bar)

TRANSMISSIONS:

HydroGear ZL-KMEF-3L7C-1LLX (LH)

HydroGear ZL-GMEF-3L7B-1LLX (RH)

Type

ZT2800

Hydraulic Fluid

SAE 20W-50 motor oil

Speeds

Forward: 0-7 MPH (0-11,27 km/h)

@ 3400 rpm

Reverse: 0-5 MPH (0-8.05 km/h)

Continuous Torque

180 ft. lbs. (244 N.m.)

Output

 

Maximum Weight

440 lbs. (200 Kg) per axle

on Axle

 

DIMENSIONS:

Overall Length:

68” (173 cm)

Overall Width

 

48” Model:

49” (125 cm)

Height:

43” (109 cm)

Weight (apx.):

750 lbs. (340 kg)

Engine Power Rating Information

The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060 RPM; horsepower values are derived at 3600 RPM. Actual gross engine power will be lower and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment (actual "on-site" or net horsepower). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine.

Specifications

41

Page 42 Page 44
Image 43
Page 42 Page 44
Contents 26HP Zero-Turn Riders ZERO-TURN Riding MowerDate Purchased Table of Contents Read the Manual Operator SafetyOperator Safety Operating SafetyThrown Objects Slope OperationMoving Parts Retaining WALLS, DROP-OFFS, and Water Fuel and MaintenanceEnclosed Areas General Operation Wear hearing protection when operating this machineTransporting and Storage Mow across slopes, not up and down Towed Equipment RIDE-ON UnitsEmissions Ignition SystemService & Maintenance Service and MaintenanceSafe Handling of Gasoline Safety Decals North American Safety Icons Safety Interlock SystemOperational Safety Checks Safety IconsFeatures and Controls Features and ControlsIdentification Numbers Ground Speed Control Levers Seat Adjustment LeverIgnition Switch Control FunctionsFeatures & Controls Checks Before Starting General Operating SafetyOperation OperationCheck Tire Pressures Seat AdjustmentTire Pressure Foot Pedal Adjustment Mowing Height AdjustmentTo adjust pedal position Pushing the Rider By Hand Insert the key into the ignition switch and turn it toStarting the Engine Stopping the RiderForward Travel Practice Zero Turn Driving PracticeForward Reverse Travel Executing Turns Practice Turning Around a CornerPractice Turning In Place Executing an End-Of-Row Zero TurnTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassMowing Methods Engine Speed & Ground Speed for Mulching Attaching a TrailerProper Mulching Mulching Requires Excellent Mowing ConditionsSafety Items Before Every Spring Regular MaintenanceRegular Maintenance Maintenance ScheduleChange Oil & Filter Engine MaintenanceChecking / Adding Fuel Fuel FilterLubricating the Front Casters LubricationGrease OilCheck / Fill Transmission Oil Change Interval Every 200 Hours Replacement Filter NumberTransmission Oil Filter Change Inspecting the Mower Blades Servicing The Mower BladesNever weld or straighten bent mower blades Balancing the Mower Blade Nail Reinstalling the Mower BladesSpeed Balancing Adjustment Ground Speed Control Lever AdjustmentNeutral Adjustment 375 0,95 cm Parking Brake AdjustmentReturn-to-Neutral Adjustment Jam Nuts Neutral Return Rod Return-to-Neutral AdjustmentMower deck Deck Rod Timing AdjustmentDeck Leveling Adjustment Adjustment is required continue with StepTo avoid damaging belts, do not PRY Belts Over Pulleys Mower Belt Replacement 48 Deck ModelsUse extreme caution when removing this spring Hydraulic Pump Drive Belt ReplacementBattery Compartment Battery MaintenanceJump Starting With Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Charging a Completely Discharged BatteryMake Certain Vehicles do not Touch Long Term Storage Longer Than 30 Days StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessTroubleshooting the Rider TroubleshootingTroubleshooting Troubleshooting ChartTroubleshooting Streaking Troubleshooting Common Cutting ProblemsChassis SpecificationsDimensions EngineSurface Vertical a with Edge this Align LineIndentification SlopePage Page Page Mower Deck Product SpecificationsCommon Service Parts Tractor

500Z specifications

The Snapper 500Z is a cutting-edge zero-turn lawn mower designed for both residential and commercial landscaping needs. This mower offers exceptional performance, versatility, and ease of use, making it a top choice for lawn care enthusiasts and professionals alike.

One of the main features of the Snapper 500Z is its powerful engine. Equipped with a reliable 23-horsepower Briggs & Stratton engine, the 500Z provides ample power to tackle challenging mowing tasks. This engine is designed to deliver smooth and consistent performance, ensuring that users can navigate their lawns with ease.

The Snapper 500Z also boasts a robust 52-inch cutting deck, made from durable materials that can withstand the rigors of regular use. With its wide cutting path, this mower allows users to cover more ground in less time, making mowing tasks quicker and more efficient. The adjustable cutting height feature provides users with the flexibility to customize their mowing height, ranging from 1.5 to 4.5 inches, ensuring a tailored cut for every lawn type.

Technology-driven features set the Snapper 500Z apart from its competitors. The mower is equipped with a hydrostatic transmission system, providing effortless control and smooth acceleration. Users can easily adjust their speed without the hassle of shifting gears, allowing for a seamless mowing experience. This system enhances mobility and maneuverability, enabling users to navigate around obstacles with precision.

Comfort and ergonomics are also a priority in the design of the Snapper 500Z. The mower features a plush, high-back seat with armrests, offering support during longer mowing sessions. An intuitive control layout ensures users can easily access all necessary functions without distraction. Additionally, the mower's compact design allows for easy storage and transportation.

Safety is paramount, and the Snapper 500Z incorporates various safety features. The operator presence control system ensures that the mower will not operate unless the user is seated, reducing the risk of accidents. Additionally, the durable roll-over protection structure (ROPS) provides an added layer of safety during operation.

In conclusion, the Snapper 500Z combines powerful performance, advanced technology, and user-friendly design to create an exceptional mowing experience. With its reliable engine, versatile cutting deck, and comfort-focused features, the Snapper 500Z is a standout choice for anyone looking to maintain a pristine lawn.
Top Page Image Contents