Snapper S200XBV32, S200XKAV2761, S200X/72 Check Hydraulic Oil Level, Change Hydraulic Oil Filter

Page 31

Check Hydraulic Oil Level

1.Before removing the reservoir cap, make sure the area around the reservoir cap and fill neck of the reservoir is free of dust, dirt, or other debris.

2.Unscrew the reservoir cap (B, Figure 25).

3.Look down the filler neck of the hydraulic oil reservoir

(A) and observe the oil level. When cold, the oil level should be approximately 4” (10 cm) below top of the filler neck.

4.If necessary, remove the reservoir cap (B) and add SAE 20W-50 motor oil.

5.Reinstall the reservoir cap.

Change Hydraulic Oil Filter

Change Interval: Every 250 Hours

Filter Part Number: 1719168

NOTE: Removing the oil filter from the filter base will drain the oil reservoir. Have a suitable container ready to catch any spilled oil. The manufacturer recommends this be a dealer-only service item.

1.Locate the transmission oil filter (B, Figure 26) at the rear of the battery compartment under the seat.

2.Lubricate the new filter base with a few drops of transmission oil. Fill the filter half full of oil.

3.Clean the area around the filter base and remove the filter. Do NOT drain the hydraulic system oil.

4.Thread the new filter onto the filter base until the gasket makes contact, then tighten 3/4 of a turn more.

5.Run the unit for several minutes and check the transmission oil level.

IMPORTANT NOTE: Use caution after changing the filter; air in the hydraulic system may affect the responsiveness of the control levers. Repeat step 5 until the air is out of the system.

Regular Maintenance

B

A

Figure 25. Checking Hydraulic Oil Level

A.Hydraulic Oil Reservoir

B.Reservoir Cap

A

B

Figure 26. Battery Compartment

A.Hydraulic Oil Reservoir

B.Hydraulic Oil Filter

Maintenance

29

Page 30 Page 32
Image 31
Page 30 Page 32
Contents OPERATOR’S Manual Date Purchased Table of Contents Read the Manual Operating SafetyChildren Thrown Objects Slope OperationMoving Parts Retaining WALLS, DROP-OFFS, and Water Roll BAR USEOverhead Obstacles Enclosed Areas Fuel and MaintenancePreparation TrainingOperation Emissions Towed Equipment RIDE-ON UnitsIgnition System Gasoline Models Safe Handling of Gasoline Service and MaintenanceOperational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Safety Decals North American Safety Icons Safety Interlock SystemOperational Safety Checks Safety IconsIdentification Numbers Features and ControlsGround Speed Levers Seat Adjustment LeverIgnition Switch Control FunctionsThrottle Control PTO Power Take Off SwitchHour Meter / Maintenance Reminder Parking BrakeChecks Before Starting General Operating SafetySeat Adjustment Suspension Seat Seat AdjustmentCheck Tire Pressures Foot Pedal Adjustment Mowing Height AdjustmentTo adjust pedal position To Lower the Roll Bar Lower the roll bar only when necessary and Never remove itRaise and Lower the Roll Bar Keep roll bar in the raised position and use the seat beltStopping the Rider Starting the EnginePushing the Rider By Hand Forward Travel Practice Zero Turn Driving PracticeForward Reverse Travel Executing Turns Practice Turning Around a CornerPractice Turning In Place Executing an End-Of-Row Zero TurnTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassMowing Methods Engine Speed & Ground Speed for Mulching Attaching a TrailerProper Mulching Mulching Requires Excellent Mowing ConditionsSafety Items Before Every Spring Maintenance ScheduleHours Fall Check Rider / Mower for loose hardware Change Oil & Filter Engine MaintenanceChecking / Adding Fuel Fuel FilterLubricating the Front Casters LubricationGrease OilChange Hydraulic Oil Filter Check Hydraulic Oil LevelChange Interval Every 250 Hours Filter Part Number Inspecting the Mower Blades Servicing The Mower BladesNever weld or straighten bent mower blades Balancing the Mower Blade Nail Reinstalling the Mower BladesSpeed Balancing Adjustment Ground Speed Control Lever AdjustmentParking Brake Adjustment Neutral AdjustmentReturn-To-Neutral Adjustment Deck Leveling Adjustment Deck Rod Timing AdjustmentTo avoid damaging belts, do not PRY Belts Over Pulleys Mower Belt ReplacementUse extreme caution when removing this spring Hydraulic Pump Drive Belt ReplacementBattery Maintenance Jump Starting With Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Charging a Completely Discharged BatteryVehicle Battery Jumper Cable To Ground Engine Block Starter Switch Jumper Cable StartingLong Term Storage Longer Than 30 Days StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessTroubleshooting the Rider Troubleshooting ChartProblem Cause Remedy Troubleshooting Streaking Troubleshooting Common Cutting ProblemsHP Briggs & Stratton SpecificationsHP Kawasaki HP KohlerFerris Limited Warranty Mower Deck TractorChassis

S200XKOH2761, S200XKAV2561, S200XBV32, S200X/72, S200XKAV2761 specifications

The Snapper S200 series is a versatile lineup of lawn care equipment designed for both residential and commercial landscaping needs. The models S200XKAV2761, S200X/72, S200XBV32, S200XKAV2561, and S200XKOH2761 are part of this series, offering robust features and advanced technologies to enhance mowing efficiency and user comfort.

The S200XKAV2761 stands out with its powerful engine that delivers optimal performance, ensuring efficient grass cutting even in thicker patches. It features a wide cutting deck that significantly reduces the time spent mowing larger areas. The innovative Easy Start technology allows users to start the engine with minimal effort, making it ideal for both seasoned users and newcomers to lawn maintenance.

Next, the S200X/72 model is characterized by its impressive 72-inch cutting deck, making it one of the most suitable options for commercial applications. This wider deck allows for less time spent mowing and more time enjoying a beautifully manicured lawn. The model incorporates premium ergonomic controls, ensuring that operators can maneuver the machine effortlessly while maintaining comfort during extended use.

The S200XBV32 model features a unique bagging system that captures grass clippings efficiently, reducing the need for additional cleanup after mowing. This model utilizes a two-stage air filtration system that prolongs engine life while boosting power, thus enhancing productivity without compromising performance.

The S200XKAV2561 is designed with adjustable cutting heights, allowing users to customize their mowing experience according to lawn conditions. This flexibility is crucial for maintaining a healthy lawn and adapting to seasonal growth patterns. Plus, the durable chassis construction offers enhanced stability and longevity, making it a reliable choice for various terrains.

Lastly, the S200XKOH2761 model incorporates advanced hydrostatic transmission technology, allowing for a smooth and responsive driving experience. This feature is particularly beneficial when navigating tight corners and intricate landscaping. Furthermore, the model is equipped with a heavy-duty steel frame, ensuring durability and resilience against wear and tear.

In conclusion, the Snapper S200 series provides a range of models tailored to meet diverse landscaping demands. With their powerful engines, innovative features, and advanced technologies, these machines are designed to make lawn care more efficient and enjoyable for users of all skill levels. Whether for residential use or professional landscaping, the Snapper S200 lineup is an excellent investment in maintaining a pristine outdoor space.
Top Page Image Contents