Snapper S200XKOH2761, S200XKAV2761 Reinstalling the Mower Blades, Balancing the Mower Blade Nail

Page 33

Sharpening the Mower Blade

CAUTION

Avoid injury! Mower blades are sharp.

•Always wear gloves when handling the mower blades.

•Always wear safety eye protection when grinding.

1.Sharpen the mower blades with grinder, hand file, or electric blade sharpener.

2.Sharpen the mower blade by removing an equal amount of material from each end of the mower blade.

3.Keep the original bevel (A, Figure 30) when grinding. DO NOT change the mower blade bevel.

4.The mower blade should have a maximum 1/64” (0,40 mm) cutting edge (B) or less.

5.Balance the mower blades before installing.

Balancing the Mower Blades

CAUTION

Avoid injury! Keep mower blades balanced.

•An unbalanced mower blade can create excessive vibration and damage the unit or cause mower blade failure.

1.Clean the mower blade to remove any dried grass or other debris.

2.See Figure 31. Put the mower blade on a nail in a vise and turn the mower blade to the horizontal position.

3.Check the balance of the mower blade. If either end of the mower blade moves downward, sharpen the heavy end until the mower blade is balanced. See Sharpening the Mower Blades for proper sharpening instructions.

4.Repeat the process until the mower blade remains in the horizontal position.

Reinstalling the Mower Blades

1.Reinstall each mower blade with the air lifts pointing up towards the mower deck as shown in Figure 32. Secure with the mower blade mounting bolt and flat washer (A & B, Figure 32) and torque to 70 ft. lbs (94 Nm).

2.If there are no flats on the spindle shaft, wedge a wooden block between the mower blade and the mower deck housing to keep the mower blade from turning.

Regular Maintenance

A

B

Figure 30. Sharpening the Mower Blade

A.Mower Blade Bevel

B.Mower Blade Cutting Edge

A

Figure 31. Balancing the Mower Blade

A. Nail

B

A

D

Figure 32. Tightening the Mower Blade for Installation

A.Mower Blade Mounting Bolt

B.Flat Washer

C.Mower Blade Air Lift (Points Up For Installation)

D.4 X 4 Wooden Block

Maintenance

31

Page 32 Page 34
Image 33
Page 32 Page 34
Contents OPERATOR’S Manual Date Purchased Table of Contents Operating Safety Read the ManualChildren Slope Operation Thrown ObjectsMoving Parts Roll BAR USE Retaining WALLS, DROP-OFFS, and WaterOverhead Obstacles Enclosed Areas Fuel and MaintenanceTraining PreparationOperation Towed Equipment RIDE-ON Units EmissionsIgnition System Gasoline Models Safe Handling of Gasoline Service and MaintenanceOperational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Safety Decals Operational Safety Checks Safety Interlock SystemSafety Icons North American Safety IconsIdentification Numbers Features and ControlsIgnition Switch Seat Adjustment LeverControl Functions Ground Speed LeversHour Meter / Maintenance Reminder PTO Power Take Off SwitchParking Brake Throttle ControlChecks Before Starting General Operating SafetySeat Adjustment Seat Adjustment Suspension SeatCheck Tire Pressures Mowing Height Adjustment Foot Pedal AdjustmentTo adjust pedal position Raise and Lower the Roll Bar Lower the roll bar only when necessary and Never remove itKeep roll bar in the raised position and use the seat belt To Lower the Roll BarStarting the Engine Stopping the RiderPushing the Rider By Hand Zero Turn Driving Practice Forward Travel PracticeForward Reverse Travel Practice Turning In Place Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn Executing TurnsMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods Proper Mulching Attaching a TrailerMulching Requires Excellent Mowing Conditions Engine Speed & Ground Speed for MulchingMaintenance Schedule Safety Items Before Every SpringHours Fall Check Rider / Mower for loose hardware Checking / Adding Fuel Engine MaintenanceFuel Filter Change Oil & FilterGrease LubricationOil Lubricating the Front CastersCheck Hydraulic Oil Level Change Hydraulic Oil FilterChange Interval Every 250 Hours Filter Part Number Servicing The Mower Blades Inspecting the Mower BladesNever weld or straighten bent mower blades Balancing the Mower Blade Nail Reinstalling the Mower BladesSpeed Balancing Adjustment Ground Speed Control Lever AdjustmentParking Brake Adjustment Neutral AdjustmentReturn-To-Neutral Adjustment Deck Leveling Adjustment Deck Rod Timing AdjustmentTo avoid damaging belts, do not PRY Belts Over Pulleys Mower Belt ReplacementUse extreme caution when removing this spring Hydraulic Pump Drive Belt ReplacementBattery Maintenance Checking Battery Voltage Battery ServiceCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryVehicle Battery Jumper Cable To Ground Engine Block Starter Switch Jumper Cable StartingStarting After Long Term Storage StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysTroubleshooting Chart Troubleshooting the RiderProblem Cause Remedy Troubleshooting Streaking Troubleshooting Common Cutting ProblemsHP Kawasaki SpecificationsHP Kohler HP Briggs & StrattonFerris Limited Warranty Tractor Mower DeckChassis

S200XKOH2761, S200XKAV2561, S200XBV32, S200X/72, S200XKAV2761 specifications

The Snapper S200 series is a versatile lineup of lawn care equipment designed for both residential and commercial landscaping needs. The models S200XKAV2761, S200X/72, S200XBV32, S200XKAV2561, and S200XKOH2761 are part of this series, offering robust features and advanced technologies to enhance mowing efficiency and user comfort.

The S200XKAV2761 stands out with its powerful engine that delivers optimal performance, ensuring efficient grass cutting even in thicker patches. It features a wide cutting deck that significantly reduces the time spent mowing larger areas. The innovative Easy Start technology allows users to start the engine with minimal effort, making it ideal for both seasoned users and newcomers to lawn maintenance.

Next, the S200X/72 model is characterized by its impressive 72-inch cutting deck, making it one of the most suitable options for commercial applications. This wider deck allows for less time spent mowing and more time enjoying a beautifully manicured lawn. The model incorporates premium ergonomic controls, ensuring that operators can maneuver the machine effortlessly while maintaining comfort during extended use.

The S200XBV32 model features a unique bagging system that captures grass clippings efficiently, reducing the need for additional cleanup after mowing. This model utilizes a two-stage air filtration system that prolongs engine life while boosting power, thus enhancing productivity without compromising performance.

The S200XKAV2561 is designed with adjustable cutting heights, allowing users to customize their mowing experience according to lawn conditions. This flexibility is crucial for maintaining a healthy lawn and adapting to seasonal growth patterns. Plus, the durable chassis construction offers enhanced stability and longevity, making it a reliable choice for various terrains.

Lastly, the S200XKOH2761 model incorporates advanced hydrostatic transmission technology, allowing for a smooth and responsive driving experience. This feature is particularly beneficial when navigating tight corners and intricate landscaping. Furthermore, the model is equipped with a heavy-duty steel frame, ensuring durability and resilience against wear and tear.

In conclusion, the Snapper S200 series provides a range of models tailored to meet diverse landscaping demands. With their powerful engines, innovative features, and advanced technologies, these machines are designed to make lawn care more efficient and enjoyable for users of all skill levels. Whether for residential use or professional landscaping, the Snapper S200 lineup is an excellent investment in maintaining a pristine outdoor space.
Top Page Image Contents