Snapper S200XKAV2761, S200XBV32, S200X/72, S200XKOH2761, S200XKAV2561 manual Troubleshooting

Page 45

 

 

 

 

 

 

Troubleshooting

 

 

Rider Troubleshooting Continued.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Problem

Cause

Remedy

 

 

Engine runs, but rider will

1.

Hydraulic release valve(s)

1.

Turn valve(s) clockwise to close.

 

 

not drive.

 

in “open” position.

 

 

 

 

 

 

2.

Belt is broken.

2.

See Drive Belt Replacement.

 

 

 

3.

Drive belt slips.

3.

See problem and cause below.

 

 

 

4.

Brake is not fully released.

4.

See authorized service dealer

 

 

 

 

 

 

 

 

 

 

Rider drive belt slips.

1.

Pulleys or belt greasy or oily.

1.

Clean as required.

 

 

 

2.

Tension too loose.

2.

Adjust spring tension.

 

 

 

 

 

 

See Drive Belt Replacement

 

 

 

3.

Belt stretched or worn.

3.

Replace belt.

 

 

 

 

 

 

 

 

 

 

Brake will not hold.

1.

Brake is incorrectly adjusted.

1.

See Brake Adjustment.

 

 

 

2.

Brake pads worn.

2.

Replace with new brake pads.

 

 

 

 

 

 

 

 

 

 

Rider steers or handles poorly.

1.

Steering linkage is loose.

1.

Check and tighten any loose connections.

 

 

 

2.

Improper tire inflation.

2.

See Regular Maintenance Section.

 

 

 

 

 

 

 

 

 

 

Troubleshooting the Mower

 

 

 

 

 

 

 

Problem

Cause

Remedy

 

 

Mower will not raise.

1.

Lift linkage not properly attached

1.

See authorized service dealer for repair.

 

 

 

 

or damaged.

 

 

 

 

 

 

 

 

 

 

 

 

 

Engine stalls easily with

1.

Engine speed too slow.

1.

Set to full throttle.

 

 

mower engaged.

2.

Ground speed too fast.

2.

Decrease Ground Speed.

 

 

 

3.

Cutting height set too low.

3.

Cut tall grass at maximum cutting

 

 

 

 

 

 

height during first pass.

 

 

 

4.

Discharge chute jamming

4.

Cut grass with discharge pointing toward

 

 

 

 

with cut grass.

 

previously cut area.

 

 

 

 

 

 

 

 

 

 

Excessive mower vibration.

1.

Blade mounting bolts are loose.

1.

Tighten to 70 ft.lbs. (94 N.m.).

 

 

 

2.

Mower blades, arbors,

2.

Check and replace as necessary.

 

 

 

 

or pulleys are bent.

 

 

 

 

 

 

3.

Mower blades are out

3.

Remove, sharpen, and balance blades.

 

 

 

 

of balance.

 

See Maintenance Section.

 

 

 

4.

Belt installed incorrectly.

4.

Reinstall Correctly.

 

 

 

 

 

 

 

 

 

 

Excessive belt wear or breakage.

1.

Bent or rough pulleys.

1.

Repair or replace.

 

 

 

2.

Using incorrect belt.

2.

Replace with correct belt.

 

 

 

 

 

 

 

 

 

 

Mower drive belt slips

1.

Idler pulley spring broken or not

1.

Repair or replace as needed.

 

 

or fails to drive.

 

properly attached.

 

 

 

 

 

 

2.

Mower drive belt broken.

2.

Replace drive belt.

 

 

 

 

 

 

 

 

 

 

Mower does not engage.

1.

Electrical wiring damage.

1.

Locate & repair damaged wire.

 

 

 

2.

PTO clutch not adjusted

2.

See PTO Clutch Adjustment section

 

 

 

3.

Battery voltage too low.

3.

Recharge battery and check alternator.

 

 

 

 

 

 

See Battery Maintenance section.

 

Troubleshooting

43

Page 44 Page 46
Image 45
Page 44 Page 46
Contents OPERATOR’S Manual Date Purchased Table of Contents Operating Safety Read the ManualChildren Slope Operation Thrown ObjectsMoving Parts Roll BAR USE Retaining WALLS, DROP-OFFS, and WaterOverhead Obstacles Enclosed Areas Fuel and MaintenanceTraining PreparationOperation Towed Equipment RIDE-ON Units EmissionsIgnition System Gasoline Models Safe Handling of Gasoline Service and MaintenanceOperational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Safety Decals Operational Safety Checks Safety Interlock SystemSafety Icons North American Safety IconsIdentification Numbers Features and ControlsIgnition Switch Seat Adjustment LeverControl Functions Ground Speed LeversHour Meter / Maintenance Reminder PTO Power Take Off SwitchParking Brake Throttle ControlChecks Before Starting General Operating SafetySeat Adjustment Seat Adjustment Suspension SeatCheck Tire Pressures Mowing Height Adjustment Foot Pedal AdjustmentTo adjust pedal position Raise and Lower the Roll Bar Lower the roll bar only when necessary and Never remove itKeep roll bar in the raised position and use the seat belt To Lower the Roll BarStarting the Engine Stopping the RiderPushing the Rider By Hand Zero Turn Driving Practice Forward Travel PracticeForward Reverse Travel Practice Turning In Place Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn Executing TurnsMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods Proper Mulching Attaching a TrailerMulching Requires Excellent Mowing Conditions Engine Speed & Ground Speed for MulchingMaintenance Schedule Safety Items Before Every SpringHours Fall Check Rider / Mower for loose hardware Checking / Adding Fuel Engine MaintenanceFuel Filter Change Oil & FilterGrease LubricationOil Lubricating the Front CastersCheck Hydraulic Oil Level Change Hydraulic Oil FilterChange Interval Every 250 Hours Filter Part Number Servicing The Mower Blades Inspecting the Mower BladesNever weld or straighten bent mower blades Balancing the Mower Blade Nail Reinstalling the Mower BladesSpeed Balancing Adjustment Ground Speed Control Lever AdjustmentParking Brake Adjustment Neutral AdjustmentReturn-To-Neutral Adjustment Deck Leveling Adjustment Deck Rod Timing AdjustmentTo avoid damaging belts, do not PRY Belts Over Pulleys Mower Belt ReplacementUse extreme caution when removing this spring Hydraulic Pump Drive Belt ReplacementBattery Maintenance Checking Battery Voltage Battery ServiceCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryVehicle Battery Jumper Cable To Ground Engine Block Starter Switch Jumper Cable StartingStarting After Long Term Storage StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysTroubleshooting Chart Troubleshooting the RiderProblem Cause Remedy Troubleshooting Streaking Troubleshooting Common Cutting ProblemsHP Kawasaki SpecificationsHP Kohler HP Briggs & StrattonFerris Limited Warranty Tractor Mower DeckChassis

S200XKOH2761, S200XKAV2561, S200XBV32, S200X/72, S200XKAV2761 specifications

The Snapper S200 series is a versatile lineup of lawn care equipment designed for both residential and commercial landscaping needs. The models S200XKAV2761, S200X/72, S200XBV32, S200XKAV2561, and S200XKOH2761 are part of this series, offering robust features and advanced technologies to enhance mowing efficiency and user comfort.

The S200XKAV2761 stands out with its powerful engine that delivers optimal performance, ensuring efficient grass cutting even in thicker patches. It features a wide cutting deck that significantly reduces the time spent mowing larger areas. The innovative Easy Start technology allows users to start the engine with minimal effort, making it ideal for both seasoned users and newcomers to lawn maintenance.

Next, the S200X/72 model is characterized by its impressive 72-inch cutting deck, making it one of the most suitable options for commercial applications. This wider deck allows for less time spent mowing and more time enjoying a beautifully manicured lawn. The model incorporates premium ergonomic controls, ensuring that operators can maneuver the machine effortlessly while maintaining comfort during extended use.

The S200XBV32 model features a unique bagging system that captures grass clippings efficiently, reducing the need for additional cleanup after mowing. This model utilizes a two-stage air filtration system that prolongs engine life while boosting power, thus enhancing productivity without compromising performance.

The S200XKAV2561 is designed with adjustable cutting heights, allowing users to customize their mowing experience according to lawn conditions. This flexibility is crucial for maintaining a healthy lawn and adapting to seasonal growth patterns. Plus, the durable chassis construction offers enhanced stability and longevity, making it a reliable choice for various terrains.

Lastly, the S200XKOH2761 model incorporates advanced hydrostatic transmission technology, allowing for a smooth and responsive driving experience. This feature is particularly beneficial when navigating tight corners and intricate landscaping. Furthermore, the model is equipped with a heavy-duty steel frame, ensuring durability and resilience against wear and tear.

In conclusion, the Snapper S200 series provides a range of models tailored to meet diverse landscaping demands. With their powerful engines, innovative features, and advanced technologies, these machines are designed to make lawn care more efficient and enjoyable for users of all skill levels. Whether for residential use or professional landscaping, the Snapper S200 lineup is an excellent investment in maintaining a pristine outdoor space.
Top Page Image Contents