Snapper S200X/72, S200XKAV2761, S200XBV32 Deck Rod Timing Adjustment, Deck Leveling Adjustment

Page 37

Regular Maintenance

Deck Rod Timing Adjustment

1. Park the machine on a flat, level surface. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key. Rear tires must be inflated to 15 psi (1,03 bar); front tires to 25 psi (1,72 bar).

2. To check the lift rod timing, measure and record the distance between the lift pivots and the rod pivots. Repeat for other side of unit. See Figure 38.

3. If the measurements for the rods are equal, no further

 

adjustment is required. If the measurements are NOT

 

equal (greater than 1/8” (3,17 mm) difference),

Figure 38. Check Lift Rod Timing

adjustment is required continue with Step 4.

4.Lock the deck lift pedal in the 5” (12,7 cm) position. Remove the cutting height adjustment pin and lower the mower deck.

5. To ensure that the deck is in the lowest position, push the pedal by hand towards the rear of the unit and install the height adjustment pin in the 3” (7,6 cm) position to hold in place.

6. Block up the mower deck until all hanger chains are slack. Refer to Figure 40.

7.See Figure 39. To adjust the lift rod, loosen the jam nut on the front clevis then remove the 1/2” clevis pin fastening the clevis to the lift pivot arm. Turn the clevis clockwise to shorten the distance between the rod pivots or counterclockwise to lengthen the distance between the rod pivots. Reinstall the clevis on the lift pivot arm and secure with the 1/2” clevis pin previously removed. Tighten the jam nut against the clevis.

8.Remove the blocks from the under the mower deck.

9.Remove the cutting height adjustment pin from in front of the deck lift pedal arm. Lift mower deck and reinstall adjustment pin in desired mowing height.

Deck Leveling Adjustment

NOTE: Before adjusting the deck level, the deck lift rod timing must be checked and/or adjusted.

1.Park the machine on a flat, level surface. Disengage the PTO, stop the engine and engage the parking brake. Rear tires must be inflated to 15 psi (1,03 bar); front tires to 25 psi (1,72 bar).

Figure 39. Adjust Lift Rod Timing

Figure 40.

2 x 4 Locations

Maintenance

2. Lock the deck lift pedal in the 5” (12,7 cm) position. Place the deck height adjustment pin in the 4” position

and lower the deck lift pedal until the arm contacts the pin.

3. Place 2 x 4 blocks under each corner of the mower deck with the 3-1/2” sides being vertical. Place a 1/4” (0,64 cm) thick spacer on top of the rear 2 x 4 blocks. See Figure 40.

4. Adjust the front eyebolts until the chains are tight and the deck is still resting on the 2 x 4’s. Tighten the jam nuts. See Figure 41.

5. Loosen the nuts and allow the rear of the deck to rest on the 2 x 4’s and 1/4” spacers. Slide the chains down in the slots until the chains are tight and tighten the nuts. See Figure 41.

6. Remove all 2 x 4 blocks and spacers from under the

Figure 41. Hanger Chain Adjustment

 

mower deck.

 

35

Page 36 Page 38
Image 37
Page 36 Page 38
Contents OPERATOR’S Manual Date Purchased Table of Contents Read the Manual Operating SafetyChildren Thrown Objects Slope OperationMoving Parts Retaining WALLS, DROP-OFFS, and Water Roll BAR USEOverhead Obstacles Enclosed Areas Fuel and MaintenancePreparation TrainingOperation Emissions Towed Equipment RIDE-ON UnitsIgnition System Gasoline Models Safe Handling of Gasoline Service and MaintenanceOperational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Safety Decals Operational Safety Checks Safety Interlock SystemSafety Icons North American Safety IconsIdentification Numbers Features and ControlsIgnition Switch Seat Adjustment LeverControl Functions Ground Speed LeversHour Meter / Maintenance Reminder PTO Power Take Off SwitchParking Brake Throttle ControlChecks Before Starting General Operating SafetySeat Adjustment Suspension Seat Seat AdjustmentCheck Tire Pressures Foot Pedal Adjustment Mowing Height AdjustmentTo adjust pedal position Raise and Lower the Roll Bar Lower the roll bar only when necessary and Never remove itKeep roll bar in the raised position and use the seat belt To Lower the Roll BarStopping the Rider Starting the EnginePushing the Rider By Hand Forward Travel Practice Zero Turn Driving PracticeForward Reverse Travel Practice Turning In Place Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn Executing TurnsMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods Proper Mulching Attaching a TrailerMulching Requires Excellent Mowing Conditions Engine Speed & Ground Speed for MulchingSafety Items Before Every Spring Maintenance ScheduleHours Fall Check Rider / Mower for loose hardware Checking / Adding Fuel Engine MaintenanceFuel Filter Change Oil & FilterGrease LubricationOil Lubricating the Front CastersChange Hydraulic Oil Filter Check Hydraulic Oil LevelChange Interval Every 250 Hours Filter Part Number Inspecting the Mower Blades Servicing The Mower BladesNever weld or straighten bent mower blades Balancing the Mower Blade Nail Reinstalling the Mower BladesSpeed Balancing Adjustment Ground Speed Control Lever AdjustmentParking Brake Adjustment Neutral AdjustmentReturn-To-Neutral Adjustment Deck Leveling Adjustment Deck Rod Timing AdjustmentTo avoid damaging belts, do not PRY Belts Over Pulleys Mower Belt ReplacementUse extreme caution when removing this spring Hydraulic Pump Drive Belt ReplacementBattery Maintenance Checking Battery Voltage Battery ServiceCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryVehicle Battery Jumper Cable To Ground Engine Block Starter Switch Jumper Cable StartingStarting After Long Term Storage StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysTroubleshooting the Rider Troubleshooting ChartProblem Cause Remedy Troubleshooting Streaking Troubleshooting Common Cutting ProblemsHP Kawasaki SpecificationsHP Kohler HP Briggs & StrattonFerris Limited Warranty Mower Deck TractorChassis

S200XKOH2761, S200XKAV2561, S200XBV32, S200X/72, S200XKAV2761 specifications

The Snapper S200 series is a versatile lineup of lawn care equipment designed for both residential and commercial landscaping needs. The models S200XKAV2761, S200X/72, S200XBV32, S200XKAV2561, and S200XKOH2761 are part of this series, offering robust features and advanced technologies to enhance mowing efficiency and user comfort.

The S200XKAV2761 stands out with its powerful engine that delivers optimal performance, ensuring efficient grass cutting even in thicker patches. It features a wide cutting deck that significantly reduces the time spent mowing larger areas. The innovative Easy Start technology allows users to start the engine with minimal effort, making it ideal for both seasoned users and newcomers to lawn maintenance.

Next, the S200X/72 model is characterized by its impressive 72-inch cutting deck, making it one of the most suitable options for commercial applications. This wider deck allows for less time spent mowing and more time enjoying a beautifully manicured lawn. The model incorporates premium ergonomic controls, ensuring that operators can maneuver the machine effortlessly while maintaining comfort during extended use.

The S200XBV32 model features a unique bagging system that captures grass clippings efficiently, reducing the need for additional cleanup after mowing. This model utilizes a two-stage air filtration system that prolongs engine life while boosting power, thus enhancing productivity without compromising performance.

The S200XKAV2561 is designed with adjustable cutting heights, allowing users to customize their mowing experience according to lawn conditions. This flexibility is crucial for maintaining a healthy lawn and adapting to seasonal growth patterns. Plus, the durable chassis construction offers enhanced stability and longevity, making it a reliable choice for various terrains.

Lastly, the S200XKOH2761 model incorporates advanced hydrostatic transmission technology, allowing for a smooth and responsive driving experience. This feature is particularly beneficial when navigating tight corners and intricate landscaping. Furthermore, the model is equipped with a heavy-duty steel frame, ensuring durability and resilience against wear and tear.

In conclusion, the Snapper S200 series provides a range of models tailored to meet diverse landscaping demands. With their powerful engines, innovative features, and advanced technologies, these machines are designed to make lawn care more efficient and enjoyable for users of all skill levels. Whether for residential use or professional landscaping, the Snapper S200 lineup is an excellent investment in maintaining a pristine outdoor space.
Top Page Image Contents