Snapper S200XKAV2561, S200XKAV2761, S200XBV32, S200X/72 manual Hydraulic Pump Drive Belt Replacement

Page 39

Hydraulic Pump Drive Belt Replacement

1.Park the tractor on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, turn off the engine, and remove the ignition key.

2.Remove the PTO drive belt (see MOWER BELT REPLACEMENT for removal instructions).

3.Remove the hardware that secures the clutch anchor pad to the PTO clutch.

WARNING

STORED ENERGY DEVICE: Improper release of the belt tension spring can result in personal injury.

Use extreme caution when removing this spring.

4.Loosen the nut on the spring anchor eyebolt (G, Figure 44) to release the majority of the belt tension. Use caution and remove the nut to completely release the tension.

5.Remove the old belt and replace it with the new one. Make sure the V-side of the belt runs in the grooves of the crankshaft pulley and pump pulleys (B & C).

6.Reinstall the spring anchor eyebolt (G) into the anchor tab and loosely fasten the nut. Adjust the anchor eyebolt until a measurement of 8-3/8” (21,2 cm) is achieved from the outside if the spring hooks. Tighten nut.

7.Reinstall the clutch anchor pad to the PTO clutch and secure with the hardware previously removed.

8.Reinstall the PTO drive belt.

Regular Maintenance

 

B

 

D

G

 

 

 

8 3/8”

E

F

(21,2 cm)

 

 

 

A

 

 

C

C

Figure 44. Hydraulic Pump Drive Belt Replacement

A.Pump Drive Belt

B.Crankshaft Pulley

C.Pump Pulley

D.Idler Pulley

E.Idler Arm

F.Spring

G.Spring Anchor Eyebolt

Maintenance

37

Page 38 Page 40
Image 39
Page 38 Page 40
Contents OPERATOR’S Manual Date Purchased Table of Contents Operating Safety Read the ManualChildren Slope Operation Thrown ObjectsMoving Parts Roll BAR USE Retaining WALLS, DROP-OFFS, and WaterOverhead Obstacles Enclosed Areas Fuel and MaintenanceTraining PreparationOperation Towed Equipment RIDE-ON Units EmissionsIgnition System Gasoline Models Safe Handling of Gasoline Service and MaintenanceOperational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Safety Decals North American Safety Icons Safety Interlock SystemOperational Safety Checks Safety IconsIdentification Numbers Features and ControlsGround Speed Levers Seat Adjustment LeverIgnition Switch Control FunctionsThrottle Control PTO Power Take Off SwitchHour Meter / Maintenance Reminder Parking BrakeChecks Before Starting General Operating SafetySeat Adjustment Seat Adjustment Suspension SeatCheck Tire Pressures Mowing Height Adjustment Foot Pedal AdjustmentTo adjust pedal position To Lower the Roll Bar Lower the roll bar only when necessary and Never remove itRaise and Lower the Roll Bar Keep roll bar in the raised position and use the seat beltStarting the Engine Stopping the RiderPushing the Rider By Hand Zero Turn Driving Practice Forward Travel PracticeForward Reverse Travel Executing Turns Practice Turning Around a CornerPractice Turning In Place Executing an End-Of-Row Zero TurnTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassMowing Methods Engine Speed & Ground Speed for Mulching Attaching a TrailerProper Mulching Mulching Requires Excellent Mowing ConditionsMaintenance Schedule Safety Items Before Every SpringHours Fall Check Rider / Mower for loose hardware Change Oil & Filter Engine MaintenanceChecking / Adding Fuel Fuel FilterLubricating the Front Casters LubricationGrease OilCheck Hydraulic Oil Level Change Hydraulic Oil FilterChange Interval Every 250 Hours Filter Part Number Servicing The Mower Blades Inspecting the Mower BladesNever weld or straighten bent mower blades Balancing the Mower Blade Nail Reinstalling the Mower BladesSpeed Balancing Adjustment Ground Speed Control Lever AdjustmentParking Brake Adjustment Neutral AdjustmentReturn-To-Neutral Adjustment Deck Leveling Adjustment Deck Rod Timing AdjustmentTo avoid damaging belts, do not PRY Belts Over Pulleys Mower Belt ReplacementUse extreme caution when removing this spring Hydraulic Pump Drive Belt ReplacementBattery Maintenance Jump Starting With Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Charging a Completely Discharged BatteryVehicle Battery Jumper Cable To Ground Engine Block Starter Switch Jumper Cable StartingLong Term Storage Longer Than 30 Days StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessTroubleshooting Chart Troubleshooting the RiderProblem Cause Remedy Troubleshooting Streaking Troubleshooting Common Cutting ProblemsHP Briggs & Stratton SpecificationsHP Kawasaki HP KohlerFerris Limited Warranty Tractor Mower DeckChassis

S200XKOH2761, S200XKAV2561, S200XBV32, S200X/72, S200XKAV2761 specifications

The Snapper S200 series is a versatile lineup of lawn care equipment designed for both residential and commercial landscaping needs. The models S200XKAV2761, S200X/72, S200XBV32, S200XKAV2561, and S200XKOH2761 are part of this series, offering robust features and advanced technologies to enhance mowing efficiency and user comfort.

The S200XKAV2761 stands out with its powerful engine that delivers optimal performance, ensuring efficient grass cutting even in thicker patches. It features a wide cutting deck that significantly reduces the time spent mowing larger areas. The innovative Easy Start technology allows users to start the engine with minimal effort, making it ideal for both seasoned users and newcomers to lawn maintenance.

Next, the S200X/72 model is characterized by its impressive 72-inch cutting deck, making it one of the most suitable options for commercial applications. This wider deck allows for less time spent mowing and more time enjoying a beautifully manicured lawn. The model incorporates premium ergonomic controls, ensuring that operators can maneuver the machine effortlessly while maintaining comfort during extended use.

The S200XBV32 model features a unique bagging system that captures grass clippings efficiently, reducing the need for additional cleanup after mowing. This model utilizes a two-stage air filtration system that prolongs engine life while boosting power, thus enhancing productivity without compromising performance.

The S200XKAV2561 is designed with adjustable cutting heights, allowing users to customize their mowing experience according to lawn conditions. This flexibility is crucial for maintaining a healthy lawn and adapting to seasonal growth patterns. Plus, the durable chassis construction offers enhanced stability and longevity, making it a reliable choice for various terrains.

Lastly, the S200XKOH2761 model incorporates advanced hydrostatic transmission technology, allowing for a smooth and responsive driving experience. This feature is particularly beneficial when navigating tight corners and intricate landscaping. Furthermore, the model is equipped with a heavy-duty steel frame, ensuring durability and resilience against wear and tear.

In conclusion, the Snapper S200 series provides a range of models tailored to meet diverse landscaping demands. With their powerful engines, innovative features, and advanced technologies, these machines are designed to make lawn care more efficient and enjoyable for users of all skill levels. Whether for residential use or professional landscaping, the Snapper S200 lineup is an excellent investment in maintaining a pristine outdoor space.
Top Page Image Contents