Snapper S200XBV32, S200XKAV2761, S200X/72, S200XKOH2761, S200XKAV2561 Return-To-Neutral Adjustment

Page 36

Maintenance

Regular Maintenance

Return-To-Neutral Adjustment

To determine if it is necessary to adjust the neutral return, perform the following steps.

1.Disengage the PTO, engage the parking brake and turn off the engine.

2.Move the ground speed control levers into the operating position, pull levers rearward and release.

3.Move the ground speed control levers out towards the neutral position. If the levers do not align with the notches in the neutral lock plate, it is necessary to adjust the adjustment linkage rod (B, Figure 37).

WARNING

To avoid serious injury, perform adjustments only with engine stopped, key removed and tractor on level ground.

Adjustment

1.Pull the ground speed control lever rearward and release to check position. If the ground speed control lever does not align itself with the notch in the neutral plate, then move the set collar (A) forward or back on the adjustment linkage rod (B) until the speed control lever aligns with the notch. Retighten the set collar.

2.Make sure that the neutral return bushing (D) is seated correctly in the spring stop plate (E).

3.Pull the ground speed control lever rearward and release to check position again. Adjust as necessary to align the ground speed control levers with the notches in the neutral lock plate.

It is important to note that after every adjustment of the neutral return rod, the lever must be pulled rearward and released to properly check the neutral position.

B

C

 

 

 

 

A

 

 

D

E

Figure 37. Neutral Return Spring Adjustment

A.Set Collar

B.Adjustment Linkage Rod

C.Neutral Return Spring

D.Neutral Return Bushing

E.Spring Stop Plate

34

www.SnapperPro.com

Page 35 Page 37
Image 36
Page 35 Page 37
Contents OPERATOR’S Manual Date Purchased Table of Contents Operating Safety Read the ManualChildren Slope Operation Thrown ObjectsMoving Parts Roll BAR USE Retaining WALLS, DROP-OFFS, and WaterOverhead Obstacles Fuel and Maintenance Enclosed AreasTraining PreparationOperation Towed Equipment RIDE-ON Units EmissionsIgnition System Gasoline Models Service and Maintenance Safe Handling of GasolineRoll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Safety Decals Safety Interlock System Operational Safety ChecksSafety Icons North American Safety IconsFeatures and Controls Identification NumbersSeat Adjustment Lever Ignition SwitchControl Functions Ground Speed LeversPTO Power Take Off Switch Hour Meter / Maintenance ReminderParking Brake Throttle ControlGeneral Operating Safety Checks Before StartingSeat Adjustment Seat Adjustment Suspension SeatCheck Tire Pressures Mowing Height Adjustment Foot Pedal AdjustmentTo adjust pedal position Lower the roll bar only when necessary and Never remove it Raise and Lower the Roll BarKeep roll bar in the raised position and use the seat belt To Lower the Roll BarStarting the Engine Stopping the RiderPushing the Rider By Hand Zero Turn Driving Practice Forward Travel PracticeForward Reverse Travel Practice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn Executing TurnsMowing Mowing RecommendationsHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods Attaching a Trailer Proper MulchingMulching Requires Excellent Mowing Conditions Engine Speed & Ground Speed for MulchingMaintenance Schedule Safety Items Before Every SpringHours Fall Check Rider / Mower for loose hardware Engine Maintenance Checking / Adding FuelFuel Filter Change Oil & FilterLubrication GreaseOil Lubricating the Front CastersCheck Hydraulic Oil Level Change Hydraulic Oil FilterChange Interval Every 250 Hours Filter Part Number Servicing The Mower Blades Inspecting the Mower BladesNever weld or straighten bent mower blades Reinstalling the Mower Blades Balancing the Mower Blade NailGround Speed Control Lever Adjustment Speed Balancing AdjustmentNeutral Adjustment Parking Brake AdjustmentReturn-To-Neutral Adjustment Deck Rod Timing Adjustment Deck Leveling AdjustmentMower Belt Replacement To avoid damaging belts, do not PRY Belts Over PulleysHydraulic Pump Drive Belt Replacement Use extreme caution when removing this springBattery Maintenance Battery Service Checking Battery VoltageCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryStarter Switch Jumper Cable Starting Vehicle Battery Jumper Cable To Ground Engine BlockStorage Starting After Long Term StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysTroubleshooting Chart Troubleshooting the RiderProblem Cause Remedy Troubleshooting Troubleshooting Common Cutting Problems StreakingSpecifications HP KawasakiHP Kohler HP Briggs & StrattonFerris Limited Warranty Tractor Mower DeckChassis

S200XKOH2761, S200XKAV2561, S200XBV32, S200X/72, S200XKAV2761 specifications

The Snapper S200 series is a versatile lineup of lawn care equipment designed for both residential and commercial landscaping needs. The models S200XKAV2761, S200X/72, S200XBV32, S200XKAV2561, and S200XKOH2761 are part of this series, offering robust features and advanced technologies to enhance mowing efficiency and user comfort.

The S200XKAV2761 stands out with its powerful engine that delivers optimal performance, ensuring efficient grass cutting even in thicker patches. It features a wide cutting deck that significantly reduces the time spent mowing larger areas. The innovative Easy Start technology allows users to start the engine with minimal effort, making it ideal for both seasoned users and newcomers to lawn maintenance.

Next, the S200X/72 model is characterized by its impressive 72-inch cutting deck, making it one of the most suitable options for commercial applications. This wider deck allows for less time spent mowing and more time enjoying a beautifully manicured lawn. The model incorporates premium ergonomic controls, ensuring that operators can maneuver the machine effortlessly while maintaining comfort during extended use.

The S200XBV32 model features a unique bagging system that captures grass clippings efficiently, reducing the need for additional cleanup after mowing. This model utilizes a two-stage air filtration system that prolongs engine life while boosting power, thus enhancing productivity without compromising performance.

The S200XKAV2561 is designed with adjustable cutting heights, allowing users to customize their mowing experience according to lawn conditions. This flexibility is crucial for maintaining a healthy lawn and adapting to seasonal growth patterns. Plus, the durable chassis construction offers enhanced stability and longevity, making it a reliable choice for various terrains.

Lastly, the S200XKOH2761 model incorporates advanced hydrostatic transmission technology, allowing for a smooth and responsive driving experience. This feature is particularly beneficial when navigating tight corners and intricate landscaping. Furthermore, the model is equipped with a heavy-duty steel frame, ensuring durability and resilience against wear and tear.

In conclusion, the Snapper S200 series provides a range of models tailored to meet diverse landscaping demands. With their powerful engines, innovative features, and advanced technologies, these machines are designed to make lawn care more efficient and enjoyable for users of all skill levels. Whether for residential use or professional landscaping, the Snapper S200 lineup is an excellent investment in maintaining a pristine outdoor space.
Top Page Image Contents