Snapper S200XKAV2761, S200XBV32, S200X/72 manual Neutral Adjustment, Parking Brake Adjustment

Page 35

Neutral Adjustment

If the tractor “creeps” while the ground speed control levers are locked in NEUTRAL, then it may be necessary to adjust the linkage rod.

NOTE: Perform this adjustment on a hard, level surface such as a concrete floor.

1.Disengage the PTO, engage the parking brake and turn off the engine.

2.There are three nuts (B, Figure 35) on the linkage rod

(A). The first two are to be used together to turn the rod and the third (towards the front of the machine) is used to lock the rod in place. Loosen the jam nut that locks against the ball joint and turn the linkage rod to adjust. If the machine creeps forward, turn the rod CLOCKWISE (while standing at the rear of the machine, facing forward), if the machine creeps backward, turn the rod

COUNTER-CLOCKWISE.

3.Lock the jam nut (B) against the ball joint when neutral is achieved.

NOTE: This adjustment should not be performed while the machine is running. It may take several attempts to achieved neutral, depending upon how much the machine creeps.

Regular Maintenance

 

A

 

B

Figure 35. Neutral Adjustment

(LH side shown)

A.

Adjustment Linkage Rod

B.

Nuts

Parking Brake Adjustment

1.Disengage the PTO, stop the engine, block the front wheels, remove the ignition key, and engage the parking brake.

2.Locate the brake spring (A, Figure 36).

3.With the parking brake engaged, measure the compressed spring length. The spring should be 2” to 2-1/8” (5,0 - 5,4 cm) when compressed.

4.If the spring is not within this range, release the parking brake and turn the adjustment nut (B) to compress or release the spring.

5.Engage the parking brake and remeasure the spring.

CAUTION

Do not adjust the spring to be shorter than

1-15/16” (4,9 cm) when compressed. This may damage the brake mechanism.

If this does not correct the braking problem, see your Snapper Pro dealer.

 

2" - 2-1/8"

 

(5,0 - 5,4cm)

A

B

Figure 36. Parking Brake Adjustment

A.Brake Spring

B.Adjustment Nut

Maintenance

33

Page 34 Page 36
Image 35
Page 34 Page 36
Contents OPERATOR’S Manual Date Purchased Table of Contents Children Operating SafetyRead the Manual Moving Parts Slope OperationThrown Objects Overhead Obstacles Roll BAR USERetaining WALLS, DROP-OFFS, and Water Enclosed Areas Fuel and MaintenanceOperation TrainingPreparation Ignition System Gasoline Models Towed Equipment RIDE-ON UnitsEmissions Safe Handling of Gasoline Service and MaintenanceOperational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Safety Decals North American Safety Icons Safety Interlock SystemOperational Safety Checks Safety IconsIdentification Numbers Features and ControlsGround Speed Levers Seat Adjustment LeverIgnition Switch Control FunctionsThrottle Control PTO Power Take Off SwitchHour Meter / Maintenance Reminder Parking BrakeChecks Before Starting General Operating SafetyCheck Tire Pressures Seat AdjustmentSeat Adjustment Suspension Seat To adjust pedal position Mowing Height AdjustmentFoot Pedal Adjustment To Lower the Roll Bar Lower the roll bar only when necessary and Never remove itRaise and Lower the Roll Bar Keep roll bar in the raised position and use the seat beltPushing the Rider By Hand Starting the EngineStopping the Rider Forward Reverse Travel Zero Turn Driving PracticeForward Travel Practice Executing Turns Practice Turning Around a CornerPractice Turning In Place Executing an End-Of-Row Zero TurnTall Grass Requires Incremental Cutting MowingMowing Recommendations Height of GrassMowing Methods Engine Speed & Ground Speed for Mulching Attaching a TrailerProper Mulching Mulching Requires Excellent Mowing ConditionsHours Fall Check Rider / Mower for loose hardware Maintenance ScheduleSafety Items Before Every Spring Change Oil & Filter Engine MaintenanceChecking / Adding Fuel Fuel FilterLubricating the Front Casters LubricationGrease OilChange Interval Every 250 Hours Filter Part Number Check Hydraulic Oil LevelChange Hydraulic Oil Filter Never weld or straighten bent mower blades Servicing The Mower BladesInspecting the Mower Blades Balancing the Mower Blade Nail Reinstalling the Mower BladesSpeed Balancing Adjustment Ground Speed Control Lever AdjustmentParking Brake Adjustment Neutral AdjustmentReturn-To-Neutral Adjustment Deck Leveling Adjustment Deck Rod Timing AdjustmentTo avoid damaging belts, do not PRY Belts Over Pulleys Mower Belt ReplacementUse extreme caution when removing this spring Hydraulic Pump Drive Belt ReplacementBattery Maintenance Jump Starting With Auxiliary Booster Battery Battery ServiceChecking Battery Voltage Charging a Completely Discharged BatteryVehicle Battery Jumper Cable To Ground Engine Block Starter Switch Jumper Cable StartingLong Term Storage Longer Than 30 Days StorageStarting After Long Term Storage Temporary Storage 30 Days Or LessProblem Cause Remedy Troubleshooting ChartTroubleshooting the Rider Troubleshooting Streaking Troubleshooting Common Cutting ProblemsHP Briggs & Stratton SpecificationsHP Kawasaki HP KohlerFerris Limited Warranty Chassis TractorMower Deck

S200XKOH2761, S200XKAV2561, S200XBV32, S200X/72, S200XKAV2761 specifications

The Snapper S200 series is a versatile lineup of lawn care equipment designed for both residential and commercial landscaping needs. The models S200XKAV2761, S200X/72, S200XBV32, S200XKAV2561, and S200XKOH2761 are part of this series, offering robust features and advanced technologies to enhance mowing efficiency and user comfort.

The S200XKAV2761 stands out with its powerful engine that delivers optimal performance, ensuring efficient grass cutting even in thicker patches. It features a wide cutting deck that significantly reduces the time spent mowing larger areas. The innovative Easy Start technology allows users to start the engine with minimal effort, making it ideal for both seasoned users and newcomers to lawn maintenance.

Next, the S200X/72 model is characterized by its impressive 72-inch cutting deck, making it one of the most suitable options for commercial applications. This wider deck allows for less time spent mowing and more time enjoying a beautifully manicured lawn. The model incorporates premium ergonomic controls, ensuring that operators can maneuver the machine effortlessly while maintaining comfort during extended use.

The S200XBV32 model features a unique bagging system that captures grass clippings efficiently, reducing the need for additional cleanup after mowing. This model utilizes a two-stage air filtration system that prolongs engine life while boosting power, thus enhancing productivity without compromising performance.

The S200XKAV2561 is designed with adjustable cutting heights, allowing users to customize their mowing experience according to lawn conditions. This flexibility is crucial for maintaining a healthy lawn and adapting to seasonal growth patterns. Plus, the durable chassis construction offers enhanced stability and longevity, making it a reliable choice for various terrains.

Lastly, the S200XKOH2761 model incorporates advanced hydrostatic transmission technology, allowing for a smooth and responsive driving experience. This feature is particularly beneficial when navigating tight corners and intricate landscaping. Furthermore, the model is equipped with a heavy-duty steel frame, ensuring durability and resilience against wear and tear.

In conclusion, the Snapper S200 series provides a range of models tailored to meet diverse landscaping demands. With their powerful engines, innovative features, and advanced technologies, these machines are designed to make lawn care more efficient and enjoyable for users of all skill levels. Whether for residential use or professional landscaping, the Snapper S200 lineup is an excellent investment in maintaining a pristine outdoor space.
Top Page Image Contents