Dynacord Discover the Features and Specifications of the DPM 4000 Stereo System
Page 22

DEVICE DESCRIPTIONS

5.1.5 2-Channel Paging Station Module (NRS 90215)

This 2-channel audio input module is meant for the connection of DPC 4000 Series paging consoles. Each of the two input channels provide RJ-45 sockets allowing the connection of up to 4 paging stations plus paging station extensions per input. The microphone terminals are interconnected via 6-conductor parallel cables. The module can be installed in slot 1 and slot 2.

Next to the electronically balanced audio input, each input connector provides a serial RS-485 interface port and the power supply connection for the paging stations (see also: pin-assignment of the RJ-45 connector). The paging stations' power supply employs an electronic, programmable fuse, through which the maximum output current can be matched to meet actual system accommodations. This prevents the entire installation from malfunction, in case of short-circuit occurring in a single paging station only.

Input channels can be switched separately onto the monitor bus and you can monitor the audio signal via headphones or loudspeaker, either which is connected to the monitor output. Automatic pilot tone surveillance of the entire input stage is integrated as well. If necessary, retrofitting the audio inputs with transformers is possible.

DPM - PCI

DPC 4000 IN

A

DPC 4000 IN

B

90215

figure 5.7 2-channel paging station module

Note: When connecting several paging consoles to a single input, please keep in mind that line interruption or short-circuit can cause malfunction of several or even all paging stations of that specific line. In emergency alert installation, connecting security-related consoles to individual inputs is therefore of major importance.

Specifications:

description

DPM-PCI 2-channel paging station module, NRS 90215

connections

2 x RJ-45 sockets

audio

 

inputs

2, electronically balanced, transformers are optionally available

nominal input level

0 dBu / 775 mV

max. input level

+12 dBu / 3 V

input impedance

20 k￿

input balancing

> -30 dB

frequency response

20 Hz ... 20 kHz, ￿ 0.5 dB

S/N ratio

> 100 dB (A-weighted)

distortion

< 0.01 %

A/D-conversion

18-bit linear, Sigma-Delta

control interfaces

2 x RS-485 standard

power supply outputs for the DPC 4000 2, short-circuit-proof, electronically programmable fuses

supply voltage

24 V DC (21.6 ... 31.2 V DC)

nominal current

330 mA, 660 mA, 990 mA (adjustable, electronic fuse)

power consumption

2 W

operational temperature range

+5 ￿C ... +40 ￿C

dimensions W x H x D

37.5 x 81 x 248 mm

weight

152 g (220 g including 2 x NRS 90208)

extensions

NRS 90208 input transformer for 1 paging station input, order-No. 121 641

5-8

PROANNOUNCE System User Handbook 1.1

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Page Page Introduction PreambleSafety Instructions Operation InstructionsProannounce System User Handbook Operation Instructions Central Unit DPM DPC 4000 Paging Stations DPA 4000 Power AmplifierDPP 4000 Power Supply Units DCS 400 Control SystemExcluded From Warranty Operation LocationSystem Description General OverviewSignal Generators / Voice Message Memory Volume And Tone Controls / DelaysAudio Routing Clock / Calendar Paging StationsControl Inputs And Outputs MonitoringMacros Safety StandardsInterfaces Installation And Program Start System Specifications Software InstallationUninstalling Proannounce Designer Starting Proannounce DesignerDigital Proannounce Manager DPM Features Description Of Individual DevicesDPM Front View Rear View Signal Pins Description +24V ==DC Input 24V == Remote Control socket RS-232 PC InterfaceSlots for Audio Output Modules Monitor Output socketExtension slot Control Module Slot Audio Input Module SlotsSupply voltage SpecificationsMonitor input Specifications 5 2-Channel Paging Station Module NRSPin-Assignment Of DPC 4000 Connectors And The Extension Cord Block DiagramRetrofitting Input Transformers Specifications 6 MIC/LINE + 2 AUX Input Module NRSBlock diagram Pin-Assignment Of XLRF-Type ConnectorsInternal Settings Retrofitting Input Transformers 7 2-Channel MIC/LINE Input Module NRS DPM MLIOpen 24 dBu Retrofitting Input Transformers 8 2-Channel AUX Input Module NRS DPM AUXBlock diagram 2-channel AUX input module 9 MIC/LINE + Paging Station Module NRS 22 MIC/LINE + paging station module NRSPin-Assignment Of RJ-45 Socket And Extension Cord Audio 24V/GNDBlock diagram MIC/LINE + paging station module Retrofitting Input Transformers 10 2-Channel Line Output Module NRS DPM OUTPin-Assignment Of XLRM-Type Connectors Setting Output Levels Via JumpersRetrofitting Output Transformers 11 8 I/O Control Module NRS 31 8 I/O control modulePin-Assignment Of RJ-45 Connectors Slave clocksFlash Memory for Voice Recording/Playback NRS Internal Message RecorderProannounce DPC 4000 Paging Consoles System Overview Paging Console Functions Table of all functionsSelection Keys and LED’s Cancel keyControl Panel Of The DPC ALL key and LEDTalk key and BUSY-LED Alarm key and IndicatorText key and LED On key and LEDDisplay ConnectionsMicrophone LAN socketKey-Labeling Tested printer models are HP LaserJet 6PSelective Call Gong Chime SignalOperation Collective CallCanceling Signals General AlarmSelective Alarm Text MessageProgram Assignment System on / OFFSpecial Functions Paging Console Configuration In Setup Mode AddressCompressor Pre-Gong SignalBuzzer LCD-ContrastIndications LEDDPC 4350 Paging Station Extension PrioritiesCombination Factory Presets Specifications DPCChange from Switch to Pushbutton Optionally Available AccessoriesOptional Alarm Key NRS Optional Key-lock Switch NRS Input / Output Transformer NRS Optional Monitor Loudspeaker NRS Connecting External Audio Signal Sources Connecting a PTT-MicrophoneExternal MIC / Line Input EXT socket Single Paging Station On a Single DPM-Line Cable LengthSingle Paging Station + Extension On a Single DPM-Line DPA 4000 Proannounce Power Amplifier Characteristics Instructions For Using Remote-Power Amps Four-Channel Power Amplifier DPA ControlControl DCS 400 Control System Characteristics Operating current FeaturesOperating voltage Operating current at 24Dimensions of the DCS 401 module DCSDCS 408 Relay Module 100 Dimensions of the DCS 408 module DCSContact current, maximum Operating temperature range Operating current, all relays pulled, at 24Maximally 12 DCS 408 / DCS 409 modules can be Operating current, all inputs open Power source 24V CN6 Maximum output currentOperating current, all inputs at +24VOUT -24VOUT Output DCS 416 Analog Input / Output Module DCS 416 analog I/O moduleDAC Dimensions W x H x D 19 2HU Specifications Operating voltageOperating temperature range Weight Audio input Input voltage 0 dB LED+10 Operation keys Function+ 24 NRS 90240 Rotary Encoder Page Proannounce Hardware Configuration 1 DCS CablingDCS 401 Addresses Voltage SupplyBefore initial operation DMM 4650 Interconnection DMM DPMNRS 90226 Adapter Printed Board Assembly

DPM 4000 specifications

The Dynacord DPM 4000 is a high-performance digital power mixer designed to cater to the needs of live sound engineers, musicians, and audio professionals. It offers an extensive range of features and cutting-edge technologies, making it the go-to choice for both small venues and large-scale productions.

One of the standout features of the DPM 4000 is its intuitive user interface. The large, bright LCD screen provides clear visibility of all essential parameters, allowing for quick adjustments even in low-light conditions. The mixer includes a comprehensive built-in effects processor, featuring multiple reverb, delay, and modulation effects that can be applied to individual channels or the overall mix. This capability provides sound engineers with the tools they need to enhance their audio output effortlessly.

The DPM 4000 is equipped with a robust 16-channel configuration, providing ample input options for microphones, instruments, and other audio sources. Each channel is fully equipped with EQ controls, gain adjustments, and auxiliary sends, allowing for precise shaping of the sound. The mixer also supports multi-track recording via USB, making it easy for users to capture performances directly to a computer.

In terms of connectivity, the Dynacord DPM 4000 excels with multiple options including XLR, TRS, and RCA inputs. Its flexible routing capabilities enable sound engineers to customize their signal flow, enhancing both versatility and convenience during live performances. Additionally, the mixer supports remote control through dedicated software applications, enabling users to manage settings from a distance, a significant advantage for live sound applications.

The DPM 4000 features advanced thermal management technology, ensuring the unit remains cool during long operational periods. This is critical for maintaining optimal performance and longevity. The built-in power amplifier delivers impressive wattage, suitable for driving various loudspeaker systems while maintaining sound clarity and fidelity.

Another notable characteristic is its rugged construction, built to withstand the rigors of touring and frequent usage. The design ensures durability in diverse environmental conditions while maintaining aesthetic appeal.

In summary, the Dynacord DPM 4000 is a versatile and powerful digital power mixer, offering a blend of user-friendly features, comprehensive control, and robust performance. Whether used in a live sound setting or for recorded sessions, it stands out as an exceptional tool for audio professionals committed to delivering high-quality sound.
Top Page Image Contents