Dynacord DPM 4000 manual Connections, Microphone, Display, LAN socket, EXT socket

Page 47

DEVICE DESCRIPTIONS

12Microphone

After pressing the TALK button and after the BUSY LED lights making announcements in pre-selected areas or groups is possible using the integrated gooseneck microphone. The optimum distance from the microphone is approximately 20 to 35 cm. The microphone pre-amplifier embodies a limiter to control signal peaks and protect the system against overdrive.

The extension socket (EXT) allows connecting a second microphone with TALK button. Assigning the function (area, group) of the external microphone is performed during the configuration via PC.

13Display

Depending on the actual operational status of the system, the LC-display with 2 lines of 16 characters each, shows information on time, operation mode, user notes, setting up, fault messages including precise device / module specification, etc.

5.2.4 Connections

1LAN socket

This is the interface for connecting DPC 4000 Series paging stations to the PROANNOUNCE system. The 8- pole RJ-45 connector provides power supply, control interface RS-485, and audio connections. The microphone terminal has to be connected to a corresponding RJ-45 wall outlet using the supplied connection cord (3 m). The following figure shows the pin-assignment of LAN socket and RJ-45 network cable. Please also pay attention to chapter 5.2.14 Cable Lengths.

figure 5.36

LAN socket and RJ-45 network cable pin-assignment

2EXT socket

Mostly, this socket is used for connecting a DPC4350 paging station extension. Use the supplied network cable (0.5 m) to connect the DPC4350 to the paging console’s EXT socket.

In case no paging station extension is being connected, utilizing the EXT socket for connecting a second microphone with TALK button or other external audio signal sources to the paging console is possible as well. Detailed information is provided in chapter 5.2.13 Optionally Available Accessories.

figure 5.37

EXT socket pin-assignment

PROANNOUNCE System User Handbook 1.1

5-33

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Page Page Preamble IntroductionOperation Instructions Safety InstructionsProannounce System User Handbook Operation Instructions Central Unit DPM DCS 400 Control System DPA 4000 Power AmplifierDPP 4000 Power Supply Units DPC 4000 Paging StationsOperation Location Excluded From WarrantyGeneral Overview System DescriptionAudio Routing Volume And Tone Controls / DelaysSignal Generators / Voice Message Memory Monitoring Paging StationsControl Inputs And Outputs Clock / CalendarInterfaces Safety StandardsMacros Software Installation Installation And Program Start System SpecificationsStarting Proannounce Designer Uninstalling Proannounce DesignerDescription Of Individual Devices Digital Proannounce Manager DPM FeaturesDPM Front View DC Input 24V == Signal Pins Description +24V ==Rear View RS-232 PC Interface Remote Control socketAudio Input Module Slots Monitor Output socketExtension slot Control Module Slot Slots for Audio Output ModulesMonitor input SpecificationsSupply voltage 5 2-Channel Paging Station Module NRS SpecificationsBlock Diagram Pin-Assignment Of DPC 4000 Connectors And The Extension CordRetrofitting Input Transformers 6 MIC/LINE + 2 AUX Input Module NRS SpecificationsInternal Settings Pin-Assignment Of XLRF-Type ConnectorsBlock diagram Retrofitting Input Transformers DPM MLI 7 2-Channel MIC/LINE Input Module NRSOpen 24 dBu Retrofitting Input Transformers DPM AUX 8 2-Channel AUX Input Module NRSBlock diagram 2-channel AUX input module 22 MIC/LINE + paging station module NRS 9 MIC/LINE + Paging Station Module NRSAudio 24V/GND Pin-Assignment Of RJ-45 Socket And Extension CordBlock diagram MIC/LINE + paging station module Retrofitting Input Transformers DPM OUT 10 2-Channel Line Output Module NRSSetting Output Levels Via Jumpers Pin-Assignment Of XLRM-Type ConnectorsRetrofitting Output Transformers 31 8 I/O control module 11 8 I/O Control Module NRSSlave clocks Pin-Assignment Of RJ-45 ConnectorsInternal Message Recorder Flash Memory for Voice Recording/Playback NRSProannounce DPC 4000 Paging Consoles System Overview Table of all functions Paging Console FunctionsALL key and LED Cancel keyControl Panel Of The DPC Selection Keys and LED’sOn key and LED Alarm key and IndicatorText key and LED Talk key and BUSY-LEDLAN socket ConnectionsMicrophone DisplayTested printer models are HP LaserJet 6P Key-LabelingCollective Call Gong Chime SignalOperation Selective CallText Message General AlarmSelective Alarm Canceling SignalsSpecial Functions System on / OFFProgram Assignment Address Paging Console Configuration In Setup ModeLCD-Contrast Pre-Gong SignalBuzzer CompressorLED IndicationsCombination PrioritiesDPC 4350 Paging Station Extension Factory Presets DPC SpecificationsOptional Alarm Key NRS Optionally Available AccessoriesChange from Switch to Pushbutton Optional Key-lock Switch NRS Input / Output Transformer NRS Optional Monitor Loudspeaker NRS External MIC / Line Input EXT socket Connecting a PTT-MicrophoneConnecting External Audio Signal Sources Single Paging Station + Extension On a Single DPM-Line Cable LengthSingle Paging Station On a Single DPM-Line DPA 4000 Proannounce Power Amplifier Characteristics Instructions For Using Remote-Power Amps Control Four-Channel Power Amplifier DPAControl DCS 400 Control System Characteristics Operating current at 24 FeaturesOperating voltage Operating currentDCS Dimensions of the DCS 401 moduleDCS 408 Relay Module 100 DCS Dimensions of the DCS 408 moduleOperating current, all relays pulled, at 24 Contact current, maximum Operating temperature rangeMaximally 12 DCS 408 / DCS 409 modules can be Operating current, all inputs at Power source 24V CN6 Maximum output currentOperating current, all inputs open +24VOUT -24VOUT Output DCS 416 analog I/O module DCS 416 Analog Input / Output ModuleDAC Weight Audio input Input voltage 0 dB LED Specifications Operating voltageOperating temperature range Dimensions W x H x D 19 2HU+ 24 Operation keys Function+10 NRS 90240 Rotary Encoder Page Cabling Proannounce Hardware Configuration 1 DCSBefore initial operation Voltage SupplyDCS 401 Addresses DMM DPM DMM 4650 InterconnectionNRS 90226 Adapter Printed Board Assembly

DPM 4000 specifications

The Dynacord DPM 4000 is a high-performance digital power mixer designed to cater to the needs of live sound engineers, musicians, and audio professionals. It offers an extensive range of features and cutting-edge technologies, making it the go-to choice for both small venues and large-scale productions.

One of the standout features of the DPM 4000 is its intuitive user interface. The large, bright LCD screen provides clear visibility of all essential parameters, allowing for quick adjustments even in low-light conditions. The mixer includes a comprehensive built-in effects processor, featuring multiple reverb, delay, and modulation effects that can be applied to individual channels or the overall mix. This capability provides sound engineers with the tools they need to enhance their audio output effortlessly.

The DPM 4000 is equipped with a robust 16-channel configuration, providing ample input options for microphones, instruments, and other audio sources. Each channel is fully equipped with EQ controls, gain adjustments, and auxiliary sends, allowing for precise shaping of the sound. The mixer also supports multi-track recording via USB, making it easy for users to capture performances directly to a computer.

In terms of connectivity, the Dynacord DPM 4000 excels with multiple options including XLR, TRS, and RCA inputs. Its flexible routing capabilities enable sound engineers to customize their signal flow, enhancing both versatility and convenience during live performances. Additionally, the mixer supports remote control through dedicated software applications, enabling users to manage settings from a distance, a significant advantage for live sound applications.

The DPM 4000 features advanced thermal management technology, ensuring the unit remains cool during long operational periods. This is critical for maintaining optimal performance and longevity. The built-in power amplifier delivers impressive wattage, suitable for driving various loudspeaker systems while maintaining sound clarity and fidelity.

Another notable characteristic is its rugged construction, built to withstand the rigors of touring and frequent usage. The design ensures durability in diverse environmental conditions while maintaining aesthetic appeal.

In summary, the Dynacord DPM 4000 is a versatile and powerful digital power mixer, offering a blend of user-friendly features, comprehensive control, and robust performance. Whether used in a live sound setting or for recorded sessions, it stands out as an exceptional tool for audio professionals committed to delivering high-quality sound.
Top Page Image Contents