Dynacord DPM 4000 manual Priorities, DPC 4350 Paging Station Extension, Combination

Page 55

DEVICE DESCRIPTIONS

5.2.9 Priorities

The PROANNOUNCE system allows setting 10 priority levels (highest priority = 10, lowest priority = 1) that include announcements, as well as alarm and gong signals, and vocal message reproduction. A higher prioritized event principally interrupts any other event with a lower priority setting. For events with equal priority the earlier launched signal is continued; has priority over the latter.

Priority level

 

Assigned

 

Description

10

 

Directing station

Highest priority; can ignite any type of events and interrupt

 

 

 

 

all other signals.

7 - 9

 

Alarm signal

Can only be interrupted from the directing station; but

 

 

 

 

interrupts all other signals that have not been launched from

 

 

 

 

the directing terminal.

6 - 7

 

Gong signal

 

Interrupts all signals that are not coming from the directing

 

 

(manual / time-controlled)

 

terminal. Time-controlled gong signals can be delayed/pre-

 

 

 

delayed by a pre-defined period of time.

 

 

 

 

2 - 8

 

Recorded message

These priorities can be freely assigned to text messages

 

 

 

 

during the configuration procedure.

2 - 6

 

Message from a paging

 

These priorities can be freely assigned to any ‘normal’

 

 

console without / with pre-

 

paging console. A pre-gong signal has the priority of the

 

 

gong signal

 

launching microphone terminal.

1

 

Program

 

Background music always has the lowest priority level.

5.2.10 DPC 4350 Paging Station Extension

The DPC 4350 paging station extension provides selection keys only. It is employed whenever a higher amount than 50 lines need to be accessed or when an installation’s requirement of group and special function keys exceeds the existing amount of selection keys. The DPC 4350 can be easily combined with any other paging station model. The following list shows the amounts of maximally accessible lines for various combinations:

Combination

Maximum amount of lines

DPC 4106 + DPC 4350

50

DPC 4510 + DPC 4350

60

DPC 4520 + DPC 4350

70

DPC 4530 + DPC 4350

80

DPC 4550 + DPC 4350

100

The extension unit is directly connected to the extension interface of the main paging station using the supplied 8- pole RJ-45 cable and plugging it into the EXT-socket. A single paging station then consists of two devices that report to a common address. Therefore the central unit recognizes them as one single microphone terminal with an increased amount of selection keys. Also from the viewpoint of the user the two devices act as only one paging station; i.e. the selection keys of the main and the slave paging station provide equal access to their assigned areas, groups and special functions.

Note: During the configuration of the system using the PROANNOUNCE Designer software, it is important that the main paging station’s EXT-socket is configured for the connection of a DPC 4350 extension.

The extension unit can only be operated together with DPC 45.. or DPC 40.. Series paging console models!

PROANNOUNCE System User Handbook 1.1

5-41

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Page Page Preamble IntroductionOperation Instructions Safety InstructionsProannounce System User Handbook Operation Instructions Central Unit DPM DCS 400 Control System DPA 4000 Power AmplifierDPP 4000 Power Supply Units DPC 4000 Paging StationsOperation Location Excluded From WarrantyGeneral Overview System DescriptionSignal Generators / Voice Message Memory Volume And Tone Controls / DelaysAudio Routing Monitoring Paging StationsControl Inputs And Outputs Clock / CalendarMacros Safety StandardsInterfaces Software Installation Installation And Program Start System SpecificationsStarting Proannounce Designer Uninstalling Proannounce DesignerDescription Of Individual Devices Digital Proannounce Manager DPM FeaturesDPM Front View Rear View Signal Pins Description +24V ==DC Input 24V == RS-232 PC Interface Remote Control socketAudio Input Module Slots Monitor Output socketExtension slot Control Module Slot Slots for Audio Output ModulesSupply voltage SpecificationsMonitor input 5 2-Channel Paging Station Module NRS SpecificationsBlock Diagram Pin-Assignment Of DPC 4000 Connectors And The Extension CordRetrofitting Input Transformers 6 MIC/LINE + 2 AUX Input Module NRS SpecificationsBlock diagram Pin-Assignment Of XLRF-Type ConnectorsInternal Settings Retrofitting Input Transformers DPM MLI 7 2-Channel MIC/LINE Input Module NRSOpen 24 dBu Retrofitting Input Transformers DPM AUX 8 2-Channel AUX Input Module NRSBlock diagram 2-channel AUX input module 22 MIC/LINE + paging station module NRS 9 MIC/LINE + Paging Station Module NRSAudio 24V/GND Pin-Assignment Of RJ-45 Socket And Extension CordBlock diagram MIC/LINE + paging station module Retrofitting Input Transformers DPM OUT 10 2-Channel Line Output Module NRSSetting Output Levels Via Jumpers Pin-Assignment Of XLRM-Type ConnectorsRetrofitting Output Transformers 31 8 I/O control module 11 8 I/O Control Module NRSSlave clocks Pin-Assignment Of RJ-45 ConnectorsInternal Message Recorder Flash Memory for Voice Recording/Playback NRSProannounce DPC 4000 Paging Consoles System Overview Table of all functions Paging Console FunctionsALL key and LED Cancel keyControl Panel Of The DPC Selection Keys and LED’sOn key and LED Alarm key and IndicatorText key and LED Talk key and BUSY-LEDLAN socket ConnectionsMicrophone DisplayTested printer models are HP LaserJet 6P Key-LabelingCollective Call Gong Chime SignalOperation Selective CallText Message General AlarmSelective Alarm Canceling SignalsProgram Assignment System on / OFFSpecial Functions Address Paging Console Configuration In Setup ModeLCD-Contrast Pre-Gong SignalBuzzer CompressorLED IndicationsDPC 4350 Paging Station Extension PrioritiesCombination Factory Presets DPC SpecificationsChange from Switch to Pushbutton Optionally Available AccessoriesOptional Alarm Key NRS Optional Key-lock Switch NRS Input / Output Transformer NRS Optional Monitor Loudspeaker NRS Connecting External Audio Signal Sources Connecting a PTT-MicrophoneExternal MIC / Line Input EXT socket Single Paging Station On a Single DPM-Line Cable LengthSingle Paging Station + Extension On a Single DPM-Line DPA 4000 Proannounce Power Amplifier Characteristics Instructions For Using Remote-Power Amps Control Four-Channel Power Amplifier DPAControl DCS 400 Control System Characteristics Operating current at 24 FeaturesOperating voltage Operating currentDCS Dimensions of the DCS 401 moduleDCS 408 Relay Module 100 DCS Dimensions of the DCS 408 moduleOperating current, all relays pulled, at 24 Contact current, maximum Operating temperature rangeMaximally 12 DCS 408 / DCS 409 modules can be Operating current, all inputs open Power source 24V CN6 Maximum output currentOperating current, all inputs at +24VOUT -24VOUT Output DCS 416 analog I/O module DCS 416 Analog Input / Output ModuleDAC Weight Audio input Input voltage 0 dB LED Specifications Operating voltageOperating temperature range Dimensions W x H x D 19 2HU+10 Operation keys Function+ 24 NRS 90240 Rotary Encoder Page Cabling Proannounce Hardware Configuration 1 DCSDCS 401 Addresses Voltage SupplyBefore initial operation DMM DPM DMM 4650 InterconnectionNRS 90226 Adapter Printed Board Assembly

DPM 4000 specifications

The Dynacord DPM 4000 is a high-performance digital power mixer designed to cater to the needs of live sound engineers, musicians, and audio professionals. It offers an extensive range of features and cutting-edge technologies, making it the go-to choice for both small venues and large-scale productions.

One of the standout features of the DPM 4000 is its intuitive user interface. The large, bright LCD screen provides clear visibility of all essential parameters, allowing for quick adjustments even in low-light conditions. The mixer includes a comprehensive built-in effects processor, featuring multiple reverb, delay, and modulation effects that can be applied to individual channels or the overall mix. This capability provides sound engineers with the tools they need to enhance their audio output effortlessly.

The DPM 4000 is equipped with a robust 16-channel configuration, providing ample input options for microphones, instruments, and other audio sources. Each channel is fully equipped with EQ controls, gain adjustments, and auxiliary sends, allowing for precise shaping of the sound. The mixer also supports multi-track recording via USB, making it easy for users to capture performances directly to a computer.

In terms of connectivity, the Dynacord DPM 4000 excels with multiple options including XLR, TRS, and RCA inputs. Its flexible routing capabilities enable sound engineers to customize their signal flow, enhancing both versatility and convenience during live performances. Additionally, the mixer supports remote control through dedicated software applications, enabling users to manage settings from a distance, a significant advantage for live sound applications.

The DPM 4000 features advanced thermal management technology, ensuring the unit remains cool during long operational periods. This is critical for maintaining optimal performance and longevity. The built-in power amplifier delivers impressive wattage, suitable for driving various loudspeaker systems while maintaining sound clarity and fidelity.

Another notable characteristic is its rugged construction, built to withstand the rigors of touring and frequent usage. The design ensures durability in diverse environmental conditions while maintaining aesthetic appeal.

In summary, the Dynacord DPM 4000 is a versatile and powerful digital power mixer, offering a blend of user-friendly features, comprehensive control, and robust performance. Whether used in a live sound setting or for recorded sessions, it stands out as an exceptional tool for audio professionals committed to delivering high-quality sound.
Top Page Image Contents