Dynacord DPM 4000 manual Optional Monitor Loudspeaker NRS

Page 61

 

DEVICE DESCRIPTIONS

Optional Monitor Loudspeaker (NRS 90209)

Brief description:

Installing the extension-kit NRS 90209, each DPC 4000 paging console (excluding the DPC

 

4106) can be retrofitted with a monitor loudspeaker. To prevent acoustic feedback between

 

speaker and microphone, the first is muted whenever the TALK key is pressed. Also

 

included is a 100V-transformer that is installed inside of a wall outlet and is used for low-

 

impedance operation of the loudspeaker.

Supplied parts:

1 prepared printed board assembly 89022 including 100V transformer and connection cords

 

1 bottom plate with printed board assembly 89021; connection cords and loudspeaker are

 

pre-mounted

Note: For being able to ship the correct bottom plate, please specify your paging console model in which the extension is going to be installed when ordering the NRS 90209!

Installation instructions:

1.Disconnect the paging console from the power supply.

2.Detach the bottom plate (6 to 8 screws, depending on the paging station model).

3.Slide the 4 rubber feet off the side of the bottom plate and attach them to the new bottom plate with the pre- mounted printed board assembly 89021.

4.Connect the plug of the printed board assembly 89021 to the terminal strip CN9 (on the little connection printed board) – refer to figure 5.42:

figure 5.42

connecting the NRS 90209 in a paging console

5.Attach the new bottom plate.

6.Reconnect the paging station to the LAN.

7.Mount the printed board assembly 89022 (including 100V transformer) inside of a standard wall outlet and connect it between the 100V line and the RJ45-wall junction box, refer to the circuit diagram. 100V loudspeaker cabling needs to be kept separated from all other paging console wiring!

figure 5.43

circuit diagram for the monitor loudspeaker extension-kit (NRS 90209)

PROANNOUNCE System User Handbook 1.1

5-47

Page 60 Page 62
Image 61
Page 60 Page 62
Contents Page Page Preamble IntroductionOperation Instructions Safety InstructionsProannounce System User Handbook Operation Instructions Central Unit DPM DPP 4000 Power Supply Units DPA 4000 Power AmplifierDPC 4000 Paging Stations DCS 400 Control SystemOperation Location Excluded From WarrantyGeneral Overview System DescriptionSignal Generators / Voice Message Memory Volume And Tone Controls / DelaysAudio Routing Control Inputs And Outputs Paging StationsClock / Calendar MonitoringMacros Safety StandardsInterfaces Software Installation Installation And Program Start System SpecificationsStarting Proannounce Designer Uninstalling Proannounce DesignerDescription Of Individual Devices Digital Proannounce Manager DPM FeaturesDPM Front View Rear View Signal Pins Description +24V ==DC Input 24V == RS-232 PC Interface Remote Control socketExtension slot Control Module Slot Monitor Output socketSlots for Audio Output Modules Audio Input Module SlotsSupply voltage SpecificationsMonitor input 5 2-Channel Paging Station Module NRS SpecificationsBlock Diagram Pin-Assignment Of DPC 4000 Connectors And The Extension CordRetrofitting Input Transformers 6 MIC/LINE + 2 AUX Input Module NRS SpecificationsBlock diagram Pin-Assignment Of XLRF-Type ConnectorsInternal Settings Retrofitting Input Transformers DPM MLI 7 2-Channel MIC/LINE Input Module NRSOpen 24 dBu Retrofitting Input Transformers DPM AUX 8 2-Channel AUX Input Module NRSBlock diagram 2-channel AUX input module 22 MIC/LINE + paging station module NRS 9 MIC/LINE + Paging Station Module NRSAudio 24V/GND Pin-Assignment Of RJ-45 Socket And Extension CordBlock diagram MIC/LINE + paging station module Retrofitting Input Transformers DPM OUT 10 2-Channel Line Output Module NRSSetting Output Levels Via Jumpers Pin-Assignment Of XLRM-Type ConnectorsRetrofitting Output Transformers 31 8 I/O control module 11 8 I/O Control Module NRSSlave clocks Pin-Assignment Of RJ-45 ConnectorsInternal Message Recorder Flash Memory for Voice Recording/Playback NRSProannounce DPC 4000 Paging Consoles System Overview Table of all functions Paging Console FunctionsControl Panel Of The DPC Cancel keySelection Keys and LED’s ALL key and LEDText key and LED Alarm key and IndicatorTalk key and BUSY-LED On key and LEDMicrophone ConnectionsDisplay LAN socketTested printer models are HP LaserJet 6P Key-LabelingOperation Gong Chime SignalSelective Call Collective CallSelective Alarm General AlarmCanceling Signals Text MessageProgram Assignment System on / OFFSpecial Functions Address Paging Console Configuration In Setup ModeBuzzer Pre-Gong SignalCompressor LCD-ContrastLED IndicationsDPC 4350 Paging Station Extension PrioritiesCombination Factory Presets DPC SpecificationsChange from Switch to Pushbutton Optionally Available AccessoriesOptional Alarm Key NRS Optional Key-lock Switch NRS Input / Output Transformer NRS Optional Monitor Loudspeaker NRS Connecting External Audio Signal Sources Connecting a PTT-MicrophoneExternal MIC / Line Input EXT socket Single Paging Station On a Single DPM-Line Cable LengthSingle Paging Station + Extension On a Single DPM-Line DPA 4000 Proannounce Power Amplifier Characteristics Instructions For Using Remote-Power Amps Control Four-Channel Power Amplifier DPAControl DCS 400 Control System Characteristics Operating voltage FeaturesOperating current Operating current at 24DCS Dimensions of the DCS 401 moduleDCS 408 Relay Module 100 DCS Dimensions of the DCS 408 moduleOperating current, all relays pulled, at 24 Contact current, maximum Operating temperature rangeMaximally 12 DCS 408 / DCS 409 modules can be Operating current, all inputs open Power source 24V CN6 Maximum output currentOperating current, all inputs at +24VOUT -24VOUT Output DCS 416 analog I/O module DCS 416 Analog Input / Output ModuleDAC Operating temperature range Specifications Operating voltageDimensions W x H x D 19 2HU Weight Audio input Input voltage 0 dB LED+10 Operation keys Function+ 24 NRS 90240 Rotary Encoder Page Cabling Proannounce Hardware Configuration 1 DCSDCS 401 Addresses Voltage SupplyBefore initial operation DMM DPM DMM 4650 InterconnectionNRS 90226 Adapter Printed Board Assembly

DPM 4000 specifications

The Dynacord DPM 4000 is a high-performance digital power mixer designed to cater to the needs of live sound engineers, musicians, and audio professionals. It offers an extensive range of features and cutting-edge technologies, making it the go-to choice for both small venues and large-scale productions.

One of the standout features of the DPM 4000 is its intuitive user interface. The large, bright LCD screen provides clear visibility of all essential parameters, allowing for quick adjustments even in low-light conditions. The mixer includes a comprehensive built-in effects processor, featuring multiple reverb, delay, and modulation effects that can be applied to individual channels or the overall mix. This capability provides sound engineers with the tools they need to enhance their audio output effortlessly.

The DPM 4000 is equipped with a robust 16-channel configuration, providing ample input options for microphones, instruments, and other audio sources. Each channel is fully equipped with EQ controls, gain adjustments, and auxiliary sends, allowing for precise shaping of the sound. The mixer also supports multi-track recording via USB, making it easy for users to capture performances directly to a computer.

In terms of connectivity, the Dynacord DPM 4000 excels with multiple options including XLR, TRS, and RCA inputs. Its flexible routing capabilities enable sound engineers to customize their signal flow, enhancing both versatility and convenience during live performances. Additionally, the mixer supports remote control through dedicated software applications, enabling users to manage settings from a distance, a significant advantage for live sound applications.

The DPM 4000 features advanced thermal management technology, ensuring the unit remains cool during long operational periods. This is critical for maintaining optimal performance and longevity. The built-in power amplifier delivers impressive wattage, suitable for driving various loudspeaker systems while maintaining sound clarity and fidelity.

Another notable characteristic is its rugged construction, built to withstand the rigors of touring and frequent usage. The design ensures durability in diverse environmental conditions while maintaining aesthetic appeal.

In summary, the Dynacord DPM 4000 is a versatile and powerful digital power mixer, offering a blend of user-friendly features, comprehensive control, and robust performance. Whether used in a live sound setting or for recorded sessions, it stands out as an exceptional tool for audio professionals committed to delivering high-quality sound.
Top Page Image Contents