Cub Cadet 7264 manual Check Front Axle Oil, Check Final Reduction Gear Case Oil

Page 37

CHECKING OIL LEVEL IN FRONT AXLE AND FINAL REDUCTION GEAR CASES.

Check the front axle and final reduction gear case oil levels after every 50 hours of operation. Check the oil level only while the engine is stopped and the tractor is standing on a level surface.

Check Front Axle Oil

The oil fill plug/dipstick is located on the left side of the axle housing. See Figure 44.

OIL FILL PLUG/DIPSTICK

FRONT AXLE

FULL MARK

Figure 44

•Clean the area around the oil fill plug/dipstick to prevent debris from entering the axle housing. See Figure 44.

•Turn the oil fill plug/dipstick counterclockwise to unscrew from the axle housing.

•Withdraw the dipstick and wipe it clean, then reinsert and screw in all the way. Unscrew and withdraw again to read the oil level. Always keep the oil level between the bottom and the full mark of the dipstick (See Figure 44).

•If the oil level is low, add only enough Cub Cadet Gear Lube to bring the level to the full mark on the dipstick. NEVER overfill the axle housing.

•Reinsert the fill plug/dipstick into the axle housing and turn clockwise to fully tighten.

Check Final Reduction Gear Case Oil

Check the oil level at the two final reduction gear case fill plugs.

•Locate the fill plugs approximately midway up on the rear of the right and left gear cases. See Figure 45.

•Remove the fill plugs and check that the oil level is at the bottom edge of the fill port opening.

FILL PLUG

LH FINAL

REDUCTION

GEAR CASE

Figure 45

•If the oil level is low, use a funnel with a flexible spout to add enough Cub Cadet Gear Lube to bring the level up to the bottom of the fill port.

•Reinstall the fill plug in each gear case.

CHANGING FRONT AXLE AND FINAL REDUCTION GEAR CASE OIL

Change the front axle and final reduction gear case oil after every 300 hours of operation. The total dry capacity of both gear cases and the axle housing is approximately 81 oz. (2.5 qts.)

Change the front axle and final reduction gear case as follows:

•Operate the tractor for a short period to warm the oil to the normal operating temperature. Place the tractor on a level surface, engage the parking brake, and stop the tractor engine.

•Clean the area around the axle drain plug, located at the center front of the axle, and the oil fill plug/dipstick to prevent debris from entering the front axle housing. Refer to Figure 44 and Figure 46.

FRONT AXLE

DRAIN PLUG

Figure 46

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Operator’s Manual Important Read Safety Rules and Instructions CarefullyCalling Service Information Table of ContentsTo the Owner Tractor Model Plate Recording Model and Serial Number InformationRops Information Plate General Operation Important Safe Operation PracticesDo not Slope OperationSafety Frame Rops Keep Hands Safety LabelsSafety Labels Floorboard and Dash Panel Mounted Controls Controls and FeaturesIgnition Switch PTO SwitchSeat Adjustment Lever Steering WheelHeadlight Switch Hazard Light SwitchDifferential Lock Pedal Parking Brake LeverPTO Indicator Light Tachometer Parking Brake Indicator LightBattery Indicator Light Engine Coolant Temperature LightPTO Reverse Override Switch Fender Mounted Conrtols and FeaturesFuel Fill Cap PTO Selection LeverCup Holder Transmission Hi/Lo Range Shift LeverHand Holds Amber Hazard LightsRollover Protective Structure Rops OperationFolding the Rops NEW Tractor BREAK-IN Procedures Safety Interlock SystemFueling the Tractor Starting the Engine Using Jumper Cables to Start the EngineStanding beside the tractor Cold Weather StartingDriving the Tractor Using the FORWARD/REVERSE PedalDriving on Slopes Stopping the TractorUsing the Differential Lock Pedal Using the HI/LO Range Shift LeverUsing the PTO Selection Lever Using the Hydraulic Lift LeverEngaging the PTO Using the PTO Reverse Override SwitchLighting Headlights and TaillightsUsing the Three Point Hitch Using the Hitch PlateHazard Lights On Demand Four Wheel DriveFront Weights Tractor WeightingWeighting the Rear of the Tractor Rear Weight BoxAdjusting the Seat AdjustmentsAdjusting the Seat Belt Three Point Hitch AdjustmentsCheck the TOE-IN AS Follows Adjusting Front Wheel TOE-INAdjusting Hydraulic Lift Feedback ROD Adjusting the BrakesGeneral Information MaintenanceLubrication and Maintenance Chart Illustration Lubrication and Maintenance Chart General Battery Information Accessing the Engine CompartmentBattery Maintenance Battery RemovalBattery Storage Tail Light Bulb Replacement Head Light Bulb ReplacementHazard Bulb Replacement Accessing the Fuse Center Instrument Panel Bulb ReplacementServicing Electrical System Instrument Panel FusesHazard Light Flasher Relay Main FuseChecking TRANSMISSION/HYDRAULIC System OIL Level Changing TRANSMISSION/HYDRAULIC System OIL Initial Break-In Period Filter Change Check Final Reduction Gear Case Oil Check Front Axle OilChanging Front Axle and Final Reduction Gear Case OIL Lubrication of Main Drive Shaft Maintenance of the Rollover Protective Structure RopsLubrication of FWD Drive Shaft Wheel Bolt TorqueTractor Storage Tire MaintenanceRemoving the Tractor from Storage Daihatsu Emission Control Defects Warranty Coverage Engine Information and MaintenanceIgnition System Cleaning the Engine Engine MaintenanceCleaning the Radiator Screen and Radiator Before servicingChanging the Engine OIL and Filter Adding Engine OILChecking Engine Coolant Level Inspection of Cooling System Hoses Changing the AIR CleanerChanging the Engine Coolant Draining The Fuel Filter Cup Servicing the Fuel FilterChanging The Fuel Filter Specifications General Dimensions Power Take-OffHydraulic Lift System BrakesDescription Optional Equipment and AccessoriesCLEVELAND, Ohio CUB Cadet LLC Post Office BOX

7264 specifications

The Cub Cadet 7264 is a powerful lawn tractor that stands out in the market for its robust performance and innovative features. Designed for both residential and commercial use, this machine combines efficiency, durability, and user-friendly technology, making it an ideal choice for anyone looking to maintain a pristine lawn.

One of the key characteristics of the Cub Cadet 7264 is its reliable engine. Equipped with a Cub Cadet 726cc engine, it delivers ample power to handle tough mowing conditions. The engine is designed for optimal fuel efficiency and low emissions, ensuring that users can operate the mower while being mindful of their environmental impact.

The mower features a cast-iron front axle, providing strength and stability, which is crucial when tackling uneven terrain. This durability is complemented by the heavy-duty steel frame construction, ensuring that the Cub Cadet 7264 can withstand the rigors of regular use. The design also incorporates a responsive hydrostatic transmission that allows for seamless speed adjustments, enabling the operator to navigate tight spaces and challenging landscapes with ease.

One of the standout features of the Cub Cadet 7264 is its 42-inch cutting deck, which is equipped with optimized airflow for superior grass cut quality. The cutting deck height can be easily adjusted, offering six different positions to cater to various grass types and cutting preferences. The mower also has a dual blade system that enhances cutting performance, ensuring a clean and even finish with every pass.

Technologically, the Cub Cadet 7264 brings modern convenience to lawn maintenance. It features a comfortable high-back seat with ergonomic support, allowing for extended use without discomfort. The intuitive controls are designed for ease of use, with a dashboard that displays essential information like fuel level and engine temperature, keeping the user informed at all times.

For added convenience, the mower comes equipped with a removable debris shield, making it easy to clean after use. The optional attachments, including baggers and mulchers, further enhance its versatility, allowing users to manage grass clippings efficiently.

In conclusion, the Cub Cadet 7264 is a remarkable lawn tractor packed with features aimed at delivering exceptional performance and user convenience. With its powerful engine, durable construction, efficient cutting capabilities, and modern technologies, it stands as an excellent choice for homeowners and landscapers alike who seek a reliable mowing solution.
Top Page Image Contents