Cub Cadet 7264 manual Instrument Panel Bulb Replacement, Servicing Electrical System, Relays

Page 33

INSTRUMENT PANEL BULB REPLACEMENT

Referring to the instrument panel information pro- vided in the CONTROL AND FEATURES section of this manual, regularly check to ensure that the instrument panel light bulbs are functioning.

To change a burned out instrument panel bulb:

•Raise the tractor hood to view the back side of the instrument panel.

•Determine the position of the burned out bulb and pull the seal plug from the back of the instrument panel. See Figure 36.

BACK OF INSTRUMENT PANEL

PTO On

Oil

Parking Brake

 

Pressure

Temperature

 

Batt. Charge

Tachometer

Hazard Lgt.

Fuel Gauge

Figure 36

•Using a small flat bladed screw driver in the slot of the bulb socket, turn the socket approxi- mately a quarter turn counterclockwise to un- lock from the instrument panel. Carefully with- draw from the panel. Note the position of the bulb socket locking tabs.

•Insert the new bulb/socket assembly into the instrument panel in the same manner, making certain the locking tabs of the socket engage the slots of the instrument panel.

•Turn the socket approximately a quarter turn clockwise to lock in place and reinsert the seal plug into the panel opening.

SERVICING ELECTRICAL SYSTEM

Fuses are installed to protect the tractor’s electrical system from damage caused by excessive amper- age. Always use the same capacity fuse for replacement. If the electrical system does not func- tion, check for blown fuses. See Figure 37

If you have a recurring problem with blown fuses, have the tractor’s electrical system checked by your Cub Cadet dealer.

GOOD BAD

Figure 37

Accessing the Fuse Center

The fuse center is located on the inside right of the dash panel. To access the fuse center, remove the dash panel insert by removing the two screws. See Figure 38.

Reposition the dash panel insert in the dash and secure with the two screws to cover the fuse center.

SCREWS

DASH

PANEL

INSERT

Figure 38

Instrument Panel Fuses

The instrument panel’s circuitry is protected by the two fuses in the fuse center. If the instrument panel does not function properly, check the fuses.

•Pull the two fuses from the fuse center and check their condition. Replace a blown fuse with the same capacity fuse (3 Amp). Refer to Figure 39.

Relays

The PTO relay and dash power relay, located in the fuse center, maintain power to each of those circuits. If one of the circuits is not functioning properly, have your dealer electrically check the relay. See Figure 39.

INSTRUMENT PANEL FUSES (3 AMP)

DASH POWER

RELAY

X

X

X

X

 

PTO RELAY

FUSE

CENTER

Figure 39

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Operator’s Manual Important Read Safety Rules and Instructions CarefullyTable of Contents Calling Service InformationTo the Owner Recording Model and Serial Number Information Tractor Model PlateRops Information Plate General Operation Important Safe Operation PracticesDo not Slope OperationSafety Frame Rops Keep Hands Safety LabelsSafety Labels Floorboard and Dash Panel Mounted Controls Controls and FeaturesIgnition Switch PTO SwitchSeat Adjustment Lever Steering WheelHeadlight Switch Hazard Light SwitchDifferential Lock Pedal Parking Brake LeverPTO Indicator Light Tachometer Parking Brake Indicator LightBattery Indicator Light Engine Coolant Temperature LightPTO Reverse Override Switch Fender Mounted Conrtols and FeaturesFuel Fill Cap PTO Selection LeverCup Holder Transmission Hi/Lo Range Shift LeverHand Holds Amber Hazard LightsOperation Rollover Protective Structure RopsFolding the Rops Safety Interlock System NEW Tractor BREAK-IN ProceduresFueling the Tractor Starting the Engine Using Jumper Cables to Start the EngineStanding beside the tractor Cold Weather StartingDriving the Tractor Using the FORWARD/REVERSE PedalDriving on Slopes Stopping the TractorUsing the Differential Lock Pedal Using the HI/LO Range Shift LeverUsing the PTO Selection Lever Using the Hydraulic Lift LeverEngaging the PTO Using the PTO Reverse Override SwitchLighting Headlights and TaillightsUsing the Three Point Hitch Using the Hitch PlateHazard Lights On Demand Four Wheel DriveFront Weights Tractor WeightingWeighting the Rear of the Tractor Rear Weight BoxAdjusting the Seat AdjustmentsAdjusting the Seat Belt Three Point Hitch AdjustmentsCheck the TOE-IN AS Follows Adjusting Front Wheel TOE-INAdjusting Hydraulic Lift Feedback ROD Adjusting the BrakesGeneral Information MaintenanceLubrication and Maintenance Chart Illustration Lubrication and Maintenance Chart General Battery Information Accessing the Engine CompartmentBattery Removal Battery MaintenanceBattery Storage Head Light Bulb Replacement Tail Light Bulb ReplacementHazard Bulb Replacement Accessing the Fuse Center Instrument Panel Bulb ReplacementServicing Electrical System Instrument Panel FusesMain Fuse Hazard Light Flasher RelayChecking TRANSMISSION/HYDRAULIC System OIL Level Changing TRANSMISSION/HYDRAULIC System OIL Initial Break-In Period Filter Change Check Front Axle Oil Check Final Reduction Gear Case OilChanging Front Axle and Final Reduction Gear Case OIL Lubrication of Main Drive Shaft Maintenance of the Rollover Protective Structure RopsLubrication of FWD Drive Shaft Wheel Bolt TorqueTractor Storage Tire MaintenanceRemoving the Tractor from Storage Daihatsu Emission Control Defects Warranty Coverage Engine Information and MaintenanceIgnition System Cleaning the Engine Engine MaintenanceCleaning the Radiator Screen and Radiator Before servicingChanging the Engine OIL and Filter Adding Engine OILChecking Engine Coolant Level Changing the AIR Cleaner Inspection of Cooling System HosesChanging the Engine Coolant Draining The Fuel Filter Cup Servicing the Fuel FilterChanging The Fuel Filter Specifications General Dimensions Power Take-OffHydraulic Lift System BrakesDescription Optional Equipment and AccessoriesCLEVELAND, Ohio CUB Cadet LLC Post Office BOX

7264 specifications

The Cub Cadet 7264 is a powerful lawn tractor that stands out in the market for its robust performance and innovative features. Designed for both residential and commercial use, this machine combines efficiency, durability, and user-friendly technology, making it an ideal choice for anyone looking to maintain a pristine lawn.

One of the key characteristics of the Cub Cadet 7264 is its reliable engine. Equipped with a Cub Cadet 726cc engine, it delivers ample power to handle tough mowing conditions. The engine is designed for optimal fuel efficiency and low emissions, ensuring that users can operate the mower while being mindful of their environmental impact.

The mower features a cast-iron front axle, providing strength and stability, which is crucial when tackling uneven terrain. This durability is complemented by the heavy-duty steel frame construction, ensuring that the Cub Cadet 7264 can withstand the rigors of regular use. The design also incorporates a responsive hydrostatic transmission that allows for seamless speed adjustments, enabling the operator to navigate tight spaces and challenging landscapes with ease.

One of the standout features of the Cub Cadet 7264 is its 42-inch cutting deck, which is equipped with optimized airflow for superior grass cut quality. The cutting deck height can be easily adjusted, offering six different positions to cater to various grass types and cutting preferences. The mower also has a dual blade system that enhances cutting performance, ensuring a clean and even finish with every pass.

Technologically, the Cub Cadet 7264 brings modern convenience to lawn maintenance. It features a comfortable high-back seat with ergonomic support, allowing for extended use without discomfort. The intuitive controls are designed for ease of use, with a dashboard that displays essential information like fuel level and engine temperature, keeping the user informed at all times.

For added convenience, the mower comes equipped with a removable debris shield, making it easy to clean after use. The optional attachments, including baggers and mulchers, further enhance its versatility, allowing users to manage grass clippings efficiently.

In conclusion, the Cub Cadet 7264 is a remarkable lawn tractor packed with features aimed at delivering exceptional performance and user convenience. With its powerful engine, durable construction, efficient cutting capabilities, and modern technologies, it stands as an excellent choice for homeowners and landscapers alike who seek a reliable mowing solution.
Top Page Image Contents