Cub Cadet 7264 manual Changing The Fuel Filter

Page 48

Changing The Fuel Filter

Replace the fuel filter cartridge after every 600 hours of operation.

NOTE: There is no shut off valve in fuel system. To stop the flow of fuel while replacing the filter, it will be necessary to carefully clamp the fuel line between the fuel tank and the filter.

•Place a suitable container beneath the filter cup.

•Clamp the fuel line just to the rear of the fuel filter. Refer to Figure 59.

•Open the cup drain and drain the filter cup into the container below. Close the cup drain. Refer to Figure 58.

•Grasp the filter cup ring and turn counterclock- wise (as viewed from the bottom of the cup) to unscrew the cup from the filter cartridge. See Figure 59.

Clamp

 

 

 

 

 

 

 

 

Fuel Line

FILTER

 

 

 

FILTER

 

 

 

 

 

LOCKING

 

 

 

 

 

 

 

BODY CAP

 

 

 

RING

 

 

 

 

 

 

 

 

 

AIR BLEED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

KNOB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FUEL

LINE

 

FILTER

CUP DRAIN

CARTRIDGE

 

FILTER CUP

 

FILTER CUP RING

Figure 59

•Turn the filter locking ring approximately 1/4 turn counterclockwise (as viewed from bottom) to unlock. Refer to Figure 59.

•Pull the filter cartridge straight downward to remove. DO NOT try to turn the filter.

•Remove the locking ring from the old filter and slide onto the new one.

•Locate the projection on the upper rim of the new filter cartridge and align with the notch in the filter body.

•Push the new filter cartridge fully up into the filter body.

•Position the locking ring and turn it clockwise to secure the filter cartridge.

NOTE: If the cartridge if not fully up into the filter body, the locking ring will not turn. Push the cartridge further up into the body.

•Thread the filter cup up onto the new filter cartridge and fully tighten.

•After checking that the filter cup and locking ring are properly installed and the cup drain is closed, remove the clamp from the fuel line.

•The filter cup should begin to fill will diesel fuel.

•Slowly turn the air bleed knob counterclockwise until fuel refills the cup and begins to seeps out around the bleed knob. Turn the air bleed knob clockwise to close. Refer to Figure 59.

•Remove the catch container and properly dispose of the diesel fuel.

•Start and run the tractor’s engine for a short period to fully bleed any residual air from the filter, fuel lines, and injection pump.

WARNING: Never loosen or remove the filter body cap (Refer to Figure 59). Diesel fuel will pour quickly from the loosened cap. Also, the cap O-ring may be damaged when the cap is retightened, causing continued leak- age of flammable fuel.

48

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Important Read Safety Rules and Instructions Carefully Operator’s ManualTable of Contents Calling Service InformationTo the Owner Recording Model and Serial Number Information Tractor Model PlateRops Information Plate Important Safe Operation Practices General OperationSlope Operation Do notSafety Frame Rops Safety Labels Keep HandsSafety Labels Controls and Features Floorboard and Dash Panel Mounted ControlsPTO Switch Ignition SwitchSeat Adjustment Lever Steering WheelHazard Light Switch Headlight SwitchDifferential Lock Pedal Parking Brake LeverParking Brake Indicator Light PTO Indicator Light TachometerBattery Indicator Light Engine Coolant Temperature LightFender Mounted Conrtols and Features PTO Reverse Override SwitchFuel Fill Cap PTO Selection LeverTransmission Hi/Lo Range Shift Lever Cup HolderHand Holds Amber Hazard LightsOperation Rollover Protective Structure RopsFolding the Rops Safety Interlock System NEW Tractor BREAK-IN ProceduresFueling the Tractor Using Jumper Cables to Start the Engine Starting the EngineStanding beside the tractor Cold Weather StartingUsing the FORWARD/REVERSE Pedal Driving the TractorDriving on Slopes Stopping the TractorUsing the HI/LO Range Shift Lever Using the Differential Lock PedalUsing the Hydraulic Lift Lever Using the PTO Selection LeverUsing the PTO Reverse Override Switch Engaging the PTOLighting Headlights and TaillightsUsing the Hitch Plate Using the Three Point HitchHazard Lights On Demand Four Wheel DriveTractor Weighting Front WeightsWeighting the Rear of the Tractor Rear Weight BoxAdjustments Adjusting the SeatAdjusting the Seat Belt Three Point Hitch AdjustmentsAdjusting Front Wheel TOE-IN Check the TOE-IN AS FollowsAdjusting the Brakes Adjusting Hydraulic Lift Feedback RODMaintenance General InformationLubrication and Maintenance Chart Illustration Lubrication and Maintenance Chart Accessing the Engine Compartment General Battery InformationBattery Removal Battery MaintenanceBattery Storage Head Light Bulb Replacement Tail Light Bulb ReplacementHazard Bulb Replacement Instrument Panel Bulb Replacement Accessing the Fuse CenterServicing Electrical System Instrument Panel FusesMain Fuse Hazard Light Flasher RelayChecking TRANSMISSION/HYDRAULIC System OIL Level Changing TRANSMISSION/HYDRAULIC System OIL Initial Break-In Period Filter Change Check Front Axle Oil Check Final Reduction Gear Case OilChanging Front Axle and Final Reduction Gear Case OIL Maintenance of the Rollover Protective Structure Rops Lubrication of Main Drive ShaftLubrication of FWD Drive Shaft Wheel Bolt TorqueTire Maintenance Tractor StorageRemoving the Tractor from Storage Engine Information and Maintenance Daihatsu Emission Control Defects Warranty CoverageIgnition System Engine Maintenance Cleaning the EngineCleaning the Radiator Screen and Radiator Before servicingAdding Engine OIL Changing the Engine OIL and FilterChecking Engine Coolant Level Changing the AIR Cleaner Inspection of Cooling System HosesChanging the Engine Coolant Servicing the Fuel Filter Draining The Fuel Filter CupChanging The Fuel Filter Specifications Power Take-Off General DimensionsHydraulic Lift System BrakesOptional Equipment and Accessories DescriptionCUB Cadet LLC Post Office BOX CLEVELAND, Ohio

7264 specifications

The Cub Cadet 7264 is a powerful lawn tractor that stands out in the market for its robust performance and innovative features. Designed for both residential and commercial use, this machine combines efficiency, durability, and user-friendly technology, making it an ideal choice for anyone looking to maintain a pristine lawn.

One of the key characteristics of the Cub Cadet 7264 is its reliable engine. Equipped with a Cub Cadet 726cc engine, it delivers ample power to handle tough mowing conditions. The engine is designed for optimal fuel efficiency and low emissions, ensuring that users can operate the mower while being mindful of their environmental impact.

The mower features a cast-iron front axle, providing strength and stability, which is crucial when tackling uneven terrain. This durability is complemented by the heavy-duty steel frame construction, ensuring that the Cub Cadet 7264 can withstand the rigors of regular use. The design also incorporates a responsive hydrostatic transmission that allows for seamless speed adjustments, enabling the operator to navigate tight spaces and challenging landscapes with ease.

One of the standout features of the Cub Cadet 7264 is its 42-inch cutting deck, which is equipped with optimized airflow for superior grass cut quality. The cutting deck height can be easily adjusted, offering six different positions to cater to various grass types and cutting preferences. The mower also has a dual blade system that enhances cutting performance, ensuring a clean and even finish with every pass.

Technologically, the Cub Cadet 7264 brings modern convenience to lawn maintenance. It features a comfortable high-back seat with ergonomic support, allowing for extended use without discomfort. The intuitive controls are designed for ease of use, with a dashboard that displays essential information like fuel level and engine temperature, keeping the user informed at all times.

For added convenience, the mower comes equipped with a removable debris shield, making it easy to clean after use. The optional attachments, including baggers and mulchers, further enhance its versatility, allowing users to manage grass clippings efficiently.

In conclusion, the Cub Cadet 7264 is a remarkable lawn tractor packed with features aimed at delivering exceptional performance and user convenience. With its powerful engine, durable construction, efficient cutting capabilities, and modern technologies, it stands as an excellent choice for homeowners and landscapers alike who seek a reliable mowing solution.
Top Page Image Contents