Cub Cadet 7264 manual Adding Engine OIL, Changing the Engine OIL and Filter

Page 44

ADDING ENGINE OIL

WARNING: Never overfill the engine crankcase. The engine may overheat and/or damage may result if the crankcase is below the “ADD” mark or over the “FULL” mark on the dipstick. For best results, fill to the “FULL” mark on the dipstick as opposed to adding a given quantity of oil. Always check the level on the dipstick before adding more oil.

Refer to the LUBRICATION TABLE in the MAINTE- NANCE SECTION of this manual to determine the proper type of oil to add to the crankcase for the conditions under which the engine will be operated.

•Place the tractor on a level surface and engage the parking brake. Stop the tractor engine and remove the ignition key.

•Clean the area around the oil filler cap to prevent debris from entering the crankcase. See Figure 51.

OIL FILL CAP

Figure 51

•Turn the oil filler cap counterclockwise to unscrew from the valve cover.

•SLOWLY pour oil into the crankcase until the oil level reaches the “FULL” mark on the dipstick. Refer to Figure 50.

•Insert the oil fill cap into the valve cover and turn clockwise until fully tightened. Reinsert the dipstick into the dipstick tube and push firmly into the tube. Clip the dipstick handle into the retaining clip.

IMPORTANT: The oil fill cap and dipstick must always be installed securely in place when the engine is running. Severe engine damage could result from failure to do so.

CHANGING THE ENGINE OIL AND FILTER

WARNING: Because the engine is run prior to draining the oil, the engine may be hot. Use caution to avoid burning yourself on engine surfaces.

The engine oil and oil filter should be changed after the first fifty hours of operation and every 150 hours thereafter. Refer to the LUBRICATION TABLE in the MAINTENANCE SECTION of this manual for the quantity of oil needed, and to determine the proper type of oil to use for the conditions under which the engine will be operated.

Run the engine for a few minutes to allow the oil in the crankcase to warm up. Warm oil will flow more freely and carry away more engine impurities. Use care to avoid burns from hot oil. While the engine oil is warm, proceed as follows:

•Place the tractor on a level surface and engage the parking brake. Stop the tractor engine and remove the ignition key.

•Clean around the base of the oil filter, the oil filler cap, and the dipstick tube to prevent debris from entering the crankcase.

•Remove the dipstick and oil fill cap from the engine. Refer to Figure 50 and Figure 51.

•Locate the engine drain plug on the right of the engine (See Figure 52). Place a suitable container below the drain plug to collect the old oil.

OIL DRAIN PLUG

RT. FRAME RAIL

Figure 52

•Turn the drain plug counter-clockwise to remove from the engine.

•Allow the old oil to completely drain from the engine crankcase into the container below.

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Important Read Safety Rules and Instructions Carefully Operator’s ManualTo the Owner Table of ContentsCalling Service Information Rops Information Plate Recording Model and Serial Number InformationTractor Model Plate Important Safe Operation Practices General OperationSlope Operation Do notSafety Frame Rops Safety Labels Keep HandsSafety Labels Controls and Features Floorboard and Dash Panel Mounted ControlsPTO Switch Ignition SwitchSeat Adjustment Lever Steering WheelHazard Light Switch Headlight SwitchDifferential Lock Pedal Parking Brake LeverParking Brake Indicator Light PTO Indicator Light TachometerBattery Indicator Light Engine Coolant Temperature LightFender Mounted Conrtols and Features PTO Reverse Override SwitchFuel Fill Cap PTO Selection LeverTransmission Hi/Lo Range Shift Lever Cup HolderHand Holds Amber Hazard LightsFolding the Rops OperationRollover Protective Structure Rops Fueling the Tractor Safety Interlock SystemNEW Tractor BREAK-IN Procedures Using Jumper Cables to Start the Engine Starting the EngineStanding beside the tractor Cold Weather StartingUsing the FORWARD/REVERSE Pedal Driving the TractorDriving on Slopes Stopping the TractorUsing the HI/LO Range Shift Lever Using the Differential Lock PedalUsing the Hydraulic Lift Lever Using the PTO Selection LeverUsing the PTO Reverse Override Switch Engaging the PTOLighting Headlights and TaillightsUsing the Hitch Plate Using the Three Point HitchHazard Lights On Demand Four Wheel DriveTractor Weighting Front WeightsWeighting the Rear of the Tractor Rear Weight BoxAdjustments Adjusting the SeatAdjusting the Seat Belt Three Point Hitch AdjustmentsAdjusting Front Wheel TOE-IN Check the TOE-IN AS FollowsAdjusting the Brakes Adjusting Hydraulic Lift Feedback RODMaintenance General InformationLubrication and Maintenance Chart Illustration Lubrication and Maintenance Chart Accessing the Engine Compartment General Battery InformationBattery Storage Battery RemovalBattery Maintenance Hazard Bulb Replacement Head Light Bulb ReplacementTail Light Bulb Replacement Instrument Panel Bulb Replacement Accessing the Fuse CenterServicing Electrical System Instrument Panel FusesChecking TRANSMISSION/HYDRAULIC System OIL Level Main FuseHazard Light Flasher Relay Changing TRANSMISSION/HYDRAULIC System OIL Initial Break-In Period Filter Change Changing Front Axle and Final Reduction Gear Case OIL Check Front Axle OilCheck Final Reduction Gear Case Oil Maintenance of the Rollover Protective Structure Rops Lubrication of Main Drive ShaftLubrication of FWD Drive Shaft Wheel Bolt TorqueTire Maintenance Tractor StorageRemoving the Tractor from Storage Engine Information and Maintenance Daihatsu Emission Control Defects Warranty CoverageIgnition System Engine Maintenance Cleaning the EngineCleaning the Radiator Screen and Radiator Before servicingAdding Engine OIL Changing the Engine OIL and FilterChecking Engine Coolant Level Changing the Engine Coolant Changing the AIR CleanerInspection of Cooling System Hoses Servicing the Fuel Filter Draining The Fuel Filter CupChanging The Fuel Filter Specifications Power Take-Off General DimensionsHydraulic Lift System BrakesOptional Equipment and Accessories DescriptionCUB Cadet LLC Post Office BOX CLEVELAND, Ohio

7264 specifications

The Cub Cadet 7264 is a powerful lawn tractor that stands out in the market for its robust performance and innovative features. Designed for both residential and commercial use, this machine combines efficiency, durability, and user-friendly technology, making it an ideal choice for anyone looking to maintain a pristine lawn.

One of the key characteristics of the Cub Cadet 7264 is its reliable engine. Equipped with a Cub Cadet 726cc engine, it delivers ample power to handle tough mowing conditions. The engine is designed for optimal fuel efficiency and low emissions, ensuring that users can operate the mower while being mindful of their environmental impact.

The mower features a cast-iron front axle, providing strength and stability, which is crucial when tackling uneven terrain. This durability is complemented by the heavy-duty steel frame construction, ensuring that the Cub Cadet 7264 can withstand the rigors of regular use. The design also incorporates a responsive hydrostatic transmission that allows for seamless speed adjustments, enabling the operator to navigate tight spaces and challenging landscapes with ease.

One of the standout features of the Cub Cadet 7264 is its 42-inch cutting deck, which is equipped with optimized airflow for superior grass cut quality. The cutting deck height can be easily adjusted, offering six different positions to cater to various grass types and cutting preferences. The mower also has a dual blade system that enhances cutting performance, ensuring a clean and even finish with every pass.

Technologically, the Cub Cadet 7264 brings modern convenience to lawn maintenance. It features a comfortable high-back seat with ergonomic support, allowing for extended use without discomfort. The intuitive controls are designed for ease of use, with a dashboard that displays essential information like fuel level and engine temperature, keeping the user informed at all times.

For added convenience, the mower comes equipped with a removable debris shield, making it easy to clean after use. The optional attachments, including baggers and mulchers, further enhance its versatility, allowing users to manage grass clippings efficiently.

In conclusion, the Cub Cadet 7264 is a remarkable lawn tractor packed with features aimed at delivering exceptional performance and user convenience. With its powerful engine, durable construction, efficient cutting capabilities, and modern technologies, it stands as an excellent choice for homeowners and landscapers alike who seek a reliable mowing solution.
Top Page Image Contents