Craftsman D30333, 919.672190 owner manual Before Starting

Page 14

3.Turn the fuel valve to the OFF position if engine will not be restarted soon.

4.Turn water source off.

5.Pull trigger on spray gun to relieve any water pressure in hose or spray gun.

6.See Storage section in this manual for proper storage procedures. NOTE: Cleaning solution must be removed from cleaning solution tanks if storing unit longer than 30 days, see Storage section for correct procedure.

BEFORE STARTING

Read and understand all Important Safety Instructions in the front of this manual and the following Cautions and Warnings before starting the pressure washer.

•Never fill fuel tank completely. Fill tank to 1/2" below bottom of filler neck to provide space for fuel expansion. Wipe any fuel spillage from engine and equipment before starting engine.

•Never fill fuel tank indoors. Never fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank.

•Never run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas.

•Never turn water supply off while pressure washer engine is running or damage to pump will result.

•DO NOT use hot water, use cold water only.

•DO NOT stop spraying water for more than two minutes at a time.

1.In a well ventilated outdoor area add fresh, high quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine.

2.Remove filler cap/dipstick and add engine oil (supplied) to engine. NOTE: There will be a slight amount of oil in the engine from factory testing. Always check oil level before each start-up.

Filler cap/dipstick

3.Verify the filter screen is in water inlet of pump. NOTE: Cone side faces out.

Filter Screen

4.Connect high pressure hose to pump outlet.

5.Connect water source to pump inlet.

NOTE: Water source must provide a minimum of 5 gallons per minute at 20 p.s.i.

High

WaterPressure

SourceHose

D30333

14- ENG

Image 14

Contents Pressure Washer Table of Contents Model No 919.672190 Pressure Washer Specification ChartSafety Guidelines Definitions EngineRisk to Breathing Maintenance InstructionsRisk of Explosion or Fire Risk to Fluid Injection Risk of Chemical BurnRisk of HOT Surfaces Risk of Unsafe OperationRisk of Electrical Shock BOX Contents Assembly Attach high pressure hose to gun. Tighten securelyBarb fitting Operation Throttle Control Lever Controls engine speed To Adjust Pressure HOW to USE Spray WandTo apply cleaning solutions HOW to USE the Dual Tank Cleaning SystemDual Tank Cleaning Solution Tips 40º fan spray Narrow jet streamTo rinse chemical using cleaning solution system tank To Shut DownBefore Starting Maintenance Customer Responsibilities Table Maintenance TaskEngine EngineInspect CleaningTo Change Oil Pump Nozzle CleaningClean and Replace Spark Plug Storage Engine PreparationDual Tank Cleaning System Troubleshooting Guide Problem Cause CorrectionProblem Problemcause Pump PulsatesKey# Description Repair PartsPressure Washer Model Number Not Shown Pressure Pump Model Number D28703 Description Part Number Honda Engine Model Number GCV160ACylinder Barrel OIL PAN Crankshaft Repair Parts Crankshaft Pulley Repair Parts FAN Cover Carburetor AIR Cleaner Muffler Flywheel Control Description Part Number QtyLabels Sears Canada, Inc., Toronto, Ont. M5B 2B8 Table DES MatièresGarantie Complète DE UN AN SUR LES Laveuses À Pression De modèle 919.672190 Laveuse à pression Tableau DES SpécificationsMesures DE Sécurité Définitions MoteurRisque PAR Inhalation Prévention Mesures DE Sécurité ImportantesRisque Dexplosion OU D’INCENDIE Prévention Risque Risque PréventionRisque Dune Utilisation NON Sécuritaire Prévention VaporisationContenu DE LA Boîte No de pièce H140Assemblage Raccord cannelé Laveuse À Pression Levier de commande des gaz Commande laUtilisation MoteurRéglage DE LA Pression Terminologie DES Laveuses À PressionUtilisation Utilisation DE LA LanceUtilisation DU Système DE Nettoyage À Deux Réservoirs Arrêt DE LA Laveuse À Pression Laide du boyau de rinçage dinjecteurAvant LE Démarrage Mise EN GardePeuvent causer des blessures graves ou la mort Entretien« Utilisation de la lance » de cette section NE laissez PAS Vérification du niveau d’huile MoteurTableau DES Responsabilités DU Client Tache D’ENTRETIEN MoteurInspection Changement de l’huileFiltre à air NettoyageLance DE Vaporisation Nettoyage et remplacement de la bougie d’allumagePompe Entreposage Préparation du moteurSystème DE Nettoyage À Deux Réservoirs Guide DE Dépannage Problème Cause CorrectionProblème Causecorrection Problème De modèle de la laveuse à pression ’article De pièce DescriptionNon illustré De modèle de la pompe refoulante D28703 Réf Description De pièce No de modèle du moteur Honda GCV160ACorps DE Cylindre Carter D’HUILE Vilebrequin Teikoku Poulie D’ARBRE À Cames Démarreur À Rappel Couvercle DE Ventilateur Carburateur Filtre À AIR Silencieux Volant Moteur Commande Étiquettes 78- FR 79- FR Get it fixed, at your home or ours