Black & Decker BDG3100-B3, BDG2600-B3 instruction manual Do not use hot water, use cold water only

Page 37

NOTICE: Risk of property damage. Never pull water supply hose to move pressure washer. This could damage hose and/or pump inlet.

•DO NOT use hot water, use cold water only.

•Never turn water supply off while pressure washer engine is running or damage to pump will result.

•DO NOT stop spraying water for more than two minutes at a time. Pump operates in bypass mode

when spray gun trigger is not pressed. If pump is left in bypass mode for more than two minutes internal components of the pump can be damaged.

If you do not understand these precautions, please contact our customer service department at www.BlackandDecker-la.com!

Prior to starting, refer to your engine manual for proper starting procedure.

1.In a well ventilated outdoor area add fresh, high quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to Engine Owners Manual for correct procedure.

2.Check engine oil level. See Engine Owners Manual for correct procedure.

3.Connect the water hose to the water source. Turn the water source on to remove all air from the hose. When a steady stream of water is present, turn the water source off.

4.Verify the filter screen (M) is in water inlet of pump.

NOTE: Cone side faces out.

8

M

5.Connect high pressure hose (C) to pump outlet (I).

9

CI

6.Connect water source (N) to pump inlet (J). NOTE: Water source must provide a minimum of 5 gallons per minute at 20 psi.

10

N J

WARNING: To reduce the possibility of contamination always protect against backflow when connected to a potable water system.

7.Choose the correct nozzle for the job to be performed. See How To Use spray Wand instructions in this section. NOTE: If applying a chemical or cleaning solution, see How To Apply Chemicals/ Cleaning Solvents instructions in this section.

8.Turn water source on.

NOTICE: Risk of property damage. Failure to do so could cause damage to the pump.

9.Remove all air from the pump and high pressure hose by depressing trigger until a steady stream of water is present.

10.Start engine. See Engine Owners Manual for correct procedure.

37- ENG

Image 37

Contents Part No Rev APR VEA EL Español EN LA ContraportadaInstalación Fácil Easy InstallationAbra Completamente Fully Open Page Instrucciones DE Seguridad Importantes Definiciones DE Normas DE Seguridad¿QUÉ Puede SUCEDER? Cómo Evitarlo Peligro Riesgo DE Explosión O IncendioEl motor CombustiblePintadas Presión a una distancia mínima deSimilar en la manguera de alta presión Un agujero o causa de pérdida de aguaIntentar realizarle mantenimiento o Lavadora a presiónManos o los brazos Que se produzcan lesiones en lasDe incendio o inhalación. Puede Lo cual podría generar peligroCausar lesiones graves o la muerte Transporta en posición verticalLimpiadores y Desgrasadores El uso de ácidos, químicosProducto Podría provocar Una Uso doméstico Recomendados El intento deElementos Básicos DE UNA Lavadora a Presión Familiarícese CON LA Lavadora a PresiónMotor Acciona la bomba de alta presión Elementos Básicos DEL Motor Instrucciones ParaConecte el tubo aplicador E a la Pistola D y ajústelo firmementeTerminología DE LA Lavadora a Presión OperaciónCaracterísticas DE Operación DE LA Lavadora a Presión Vinilo, revestimiento Estuco y ladrillo pintadoExterior pintado Aplicación de productos químicos BDG2600-B3 Cómo Emplear Productos Químicos Y Solventes Para LimpiezaLuego de usar productos químicos, coloque la manga de Aplicación de productos químicos BDG3100-B3No use agua caliente, sólo agua fría Arranque FIGSuelte el gatillo para detener el flujo de agua Apagado MantenimientoMotor Bomba ConexionesBomba FIG Cómo Limpiar EL Filtro DE Entrada DEL Agua FIGEspecificaciones AccesoriosModelo BDG2600-B3 BDG3100-B3Garantía Limitada Información DE ServicioGarantía DEL Motor Responsabilidad DEL Comprador Original Usuario InicialProblema Causa Corrección Guía DE Diagnóstico DE ProblemasEsta Garantía no Cubre PÉRDIDAS, Daños NI Gastos LAS Garantías IMPLÍCITAS, Incluidas LAS DE ComercialidadPara el Limpiador de Boquillas Para el Uso del Tubo AplicadorEl Uso del Tubo Aplicador 25- SP Important Safety Instructions Safety Guidelines DefinitionsWhat can Happen HOW to Prevent IT Never touch, grasp or attempt to cover Do not spray flammable liquidsGuns with this pressure washer, do When using replacement lances orNot use a lance and/or lance/gun Combination that is shorter in lengthDo not use pressure washer while Washer at all timesCarpet, paint or other surfaces Upon arrival at your destinationOr any kind of flammable solvent Osene, or any other flammableWith this product could result Unplug any electrically operatedBasic Elements of a Pressure Washer FIG GET to Know the Pressure WasherOperation Assembly InstructionsBasic Elements of AN Engine Pressure Washer Terminology Pressure Adjustments Pressure Washer Operating Features HOW to USE Spray Wand Thermal Relief ValveYellow Unpainted Or brick walkways Hard surfaces Nozzle Spray Uses Surfaces Color PatternStarting FIG Damaged due to chemicals will not be covered under warrantyTo Apply chemicals BDG3100-B3 Do not use hot water, use cold water only Nozzle Cleaning FIG MaintenanceShutting Down Engine Pump ConnectionsDamage is not Covered by the Warranty Clean the Water Inlet Filter FIGStorage EngineService Information Accessories SpecificationsLimited Warranty Pressure WasherResponsibility of Original Purchaser Initial User Operational Possible Cause Solution Issue Trouble Shooting GuideSee How to Use Spray See Nozzle CleaningCorrect procedure Into cleaning solutionWill not draw Spray wand not Chemicals Low pressure Wand paragraphEnsamblado EN LOS E.E.U.U Made in USA