Black & Decker BDG2600-B3, BDG3100-B3 Pressure Washer Operating Features, Thermal Relief Valve

Page 34

trigger gun and reposition themselves without having to turn the engine off in between cleaning actions.

NOTICE: Allowing the unit to run for more than two minutes without the gun trigger being pulled could cause overheating and damage to the pump. Do not let the pressure washer run for more than two minutes in Bypass Mode. Turn off the engine and relieve the pressure in the gun during these extended situations.

Thermal Relief Valve

 

5

(P):

When

the

 

temperature

inside

the

 

pump rises too high, this

P

valve

will

open

and

 

release a gush of water in an effort to lower the temperature inside the pump. The valve will then close.

Detergent Injection System: Mixes cleaners or cleaning solvents with the water to improve cleaning effectiveness.

Water Supply: All pressure washers must have a source of water. The minimum requirements for a water supply are 20 psi and 5 Gallons Per Minute. If your water source is a well, the garden hose length can only be 30 ft. (9 m) max.

WARNING: To reduce the possibility of contamination always protect against backflow when connected to a potable water system.

PRESSURE WASHER

OPERATING FEATURES

PRESSURE ADJUSTMENTS

The pressure setting is preset at the factory to achieve opti­mum­ pressure­ and cleaning. If you need to lower the pressure,­ it can be accomplished by these methods­.

1.Back away from the surface­ to be cleaned. The further away you are, the less the pressure will be on the surface to be cleaned.

2.Change to the 40˚ nozzle (white). This nozzle delivers a less powerful stream of water and a wider spray pattern. Refer to How To Use Spray Wand.

NOTICE: DO NOT attempt to increase pump pressure. A higher pressure setting than the factory set pressure may damage pump.

HOW TO USE SPRAY WAND

The nozzles for the spray wand are stored in the nozzle holder on the panel assembly. Colors on the panel identify nozzle location and spray pattern. Refer to the following chart to choose the correct nozzle for the job to be performed.

CHANGING NOZZLES ON SPRAY WAND

DANGER: Risk of fluid injection. Do not direct discharge stream toward persons, unprotected skin, eyes or any pets or animals. Serious injury will occur.

WARNING: Flying objects could cause risk of serious injury. DO NOT attempt to change nozzles while pressure washer is running. Turn engine off before changing nozzles.

1.Pull quick-connect coupler (E) back and insert nozzle (K).

6

K

E

2.Release quick-connect coupler and twist nozzle to make sure it is secure in coupler.

WARNING: Flying object could cause risk of serious injury. Ensure nozzle is completely inserted in quick- connect socket and quick-connect snap ring is fully engaged (forward) before squeezing gun trigger.

34- ENG­

Image 34
Contents VEA EL Español EN LA Contraportada Part No Rev APREasy Installation Instalación FácilAbra Completamente Fully Open Page Definiciones DE Normas DE Seguridad Instrucciones DE Seguridad ImportantesEl motor Peligro Riesgo DE Explosión O Incendio¿QUÉ Puede SUCEDER? Cómo Evitarlo CombustiblePresión a una distancia mínima de PintadasIntentar realizarle mantenimiento o Un agujero o causa de pérdida de aguaSimilar en la manguera de alta presión Lavadora a presiónQue se produzcan lesiones en las Manos o los brazosCausar lesiones graves o la muerte Lo cual podría generar peligroDe incendio o inhalación. Puede Transporta en posición verticalProducto Podría provocar Una Uso doméstico Recomendados El uso de ácidos, químicosLimpiadores y Desgrasadores El intento deElementos Básicos DE UNA Lavadora a Presión Familiarícese CON LA Lavadora a PresiónMotor Acciona la bomba de alta presión Conecte el tubo aplicador E a la Instrucciones ParaElementos Básicos DEL Motor Pistola D y ajústelo firmementeTerminología DE LA Lavadora a Presión OperaciónCaracterísticas DE Operación DE LA Lavadora a Presión Vinilo, revestimiento Estuco y ladrillo pintadoExterior pintado Luego de usar productos químicos, coloque la manga de Cómo Emplear Productos Químicos Y Solventes Para LimpiezaAplicación de productos químicos BDG2600-B3 Aplicación de productos químicos BDG3100-B3Arranque FIG No use agua caliente, sólo agua fríaSuelte el gatillo para detener el flujo de agua Motor MantenimientoApagado Bomba ConexionesCómo Limpiar EL Filtro DE Entrada DEL Agua FIG Bomba FIGModelo AccesoriosEspecificaciones BDG2600-B3 BDG3100-B3Garantía DEL Motor Información DE ServicioGarantía Limitada Responsabilidad DEL Comprador Original Usuario InicialEsta Garantía no Cubre PÉRDIDAS, Daños NI Gastos Guía DE Diagnóstico DE ProblemasProblema Causa Corrección LAS Garantías IMPLÍCITAS, Incluidas LAS DE ComercialidadPara el Limpiador de Boquillas Para el Uso del Tubo AplicadorEl Uso del Tubo Aplicador 25-­ SP Safety Guidelines Definitions Important Safety InstructionsWhat can Happen HOW to Prevent IT Do not spray flammable liquids Never touch, grasp or attempt to coverNot use a lance and/or lance/gun When using replacement lances orGuns with this pressure washer, do Combination that is shorter in lengthCarpet, paint or other­ surfaces Washer at all timesDo not use pressure washer while Upon arrival at your destinationWith this product could result­ Osene,­ or any other flammableOr any kind of flamma­ble­ solvent Unplug any electri­cal­ly­ oper­at­ed­GET to Know the Pressure Washer Basic Elements of a Pressure Washer FIGBasic Elements of AN Engine Assembly InstructionsOperation Pressure Washer TerminologyHOW to USE Spray Wand Pressure Washer Operating FeaturesPressure Adjustments Thermal Relief ValveNozzle Spray Uses Surfaces Color Pattern Yellow Unpainted Or brick walkways Hard surfacesStarting FIG Damaged due to chemicals will not be covered under warrantyTo Apply chemicals BDG3100-B3 Do not use hot water, use cold water only Shutting Down MaintenanceNozzle Cleaning FIG Engine Pump ConnectionsStorage Clean the Water Inlet Filter FIGDamage is not Covered by the Warranty EngineLimited Warranty Accessories SpecificationsService Information Pressure WasherResponsibility of Original Purchaser Initial User See How to Use Spray Trouble Shooting GuideOperational Possible Cause Solution Issue See Nozzle CleaningWill not draw Spray wand not Into cleaning solutionCorrect procedure Chemicals Low pressure Wand paragraphEnsamblado EN LOS E.E.U.U Made in USA