Zenoah BCZ2601S manual HOW to MIX Fuel, Fueling the Unit, For Your Engine LIFE, Avoid

Page 22

English

7. Fuel

■HOW TO MIX FUEL

IMPORTANT

Agitate carefully.

1.Measure out the quantities of gasoline and oil to be mixed.

2.Put some of the gasoline into a clean, approved fuel container.

3.Pour in all of the oil and agitate well.

4.Pour In the rest of gasoline and agitate again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormal lean mixture.

5.Put a clear indication on the outside of the container to avoid mixing up with other containers.

■FUELING THE UNIT

1.Untwist and remove the fuel cap. Keep the cap and inlet of the tank clean.

2.Put fuel into the fuel tank to 80% of the full capacity.

3.Fasten the fuel cap securely and wipe up any fuel spillage around the unit.

WARNING

1.Select bare ground for fueling.

2.Move at least 10feet (3meters) away from the fueling point before starting the engine.

3.Stop the engine before refueling the unit. At that time, be sure to sufficiently agitate the mixed gasoline in the container.

FOR YOUR ENGINE LIFE, AVOID;

1. FUEL WITH NO OIL(RAW GASOLINE) – It will

22

Image 22

Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual Specifications Parts locationFiche technique Emplacement des pieces Situación de las piezasEspecificaciohes Symbols on the machine PositionEmplacement PosiciónWorking Condition For safe operationWorking Circumstance Condiciones DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail PrecaucionesWorking Plan Before Starting the EngineDE LA Machine Plan DE TravailPlan DE Trabajo Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineArranque DEL Motor Demarrage DU MoteurUtilisation DE LA Machine USO DEL Producto Maintenance If Someone ComesSI Alguien SE Aproxima SI QUELQU’UN S’APPROCHEEntretien MantenimientoRefill after cooling the engine Handling FuelTransportation Manipulación DEL Combustible Manipulation DU CarburantTransport Llenar una vez que el motor se haya enfriadoSet up Assemblage Montaje Fuel When using RedMax/ZENOAH genuine oilRecommended Mixing Ratio Gasoline 50OIL Lors de l’utilisation de la véritable huile RedMax/ZENOAH Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFueling the Unit HOW to MIX FuelFor Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Cutting head will start rotating upon the engine starts OperationOP1 OP2 Starting Engine OP3Fonctionnement Uso Palanca del estrangulador 2 cerrarOP5 Adjusting Throttle CableAdjusting Idling Speed OP6 OP6 Stopping Engine OP3Reglage DU Ralenti OP6 Reglage Câble D’ACCÉLÉRATEURAjuste Cable DEL Acelerador Travail DE Coupe Utilisation DE LA Tete a FILAdjusting the Line Length OP7Reglage DE LA Longeur DU FIL DE Coupe Ajuste DE LA Longitud DE LA LíneaMaintenance Maintenance ChartTableau D’ENTRETIEN EntretienMantenimiento Tabla DE MantenimientoAIR Filter MA1 MA2 MA3Refilling Trimming Line MA1 Fuel FilterFiltre a Carburant Entretien MantenimientoFiltre a AIR Filtro DE AireSpark Plug Replacement Plug is a NGK CMR7HMA4 Tightening TorquePARE-ETINCELLES Couple DE SerrageSilencieux LA Bujía DE Recambio Debe SER UNA Bujía NGK CMR7HIntake AIR Cooling Vent MA6Gear Case MA6 MA7Boitier DE Renvoi D’ANGLE MA6 Caja DE Engranajes MA6 Cilindro Toma de aire de refrigeración posteriorDisposal Procedures to be Performed After Every 100 Hours of USEStorage MA8Rangement Almacenamiento Entretien MantenimientoMise au rebut Eliminación 26~43.5 in-lbs 2.94~4.9 N.m Guard T3246-24110 Optional blade usageOPT1 OPT2 Bracket Handle26 43,5 pulg.-lbs Utilisation de la lame optionnelle Uso de hoja opcionalPAR Torsor 94 4,9 N.mOPT3 OPT4 OPT5 SET UP the BladeChoose the Blade Mise EN Place DE LA Lame Monte LA Hoja Choisir LA LameElija LA Hoja StandardCutting Method OPT6 OPT7 OPT8 OPT9Operation Método DE Corte Methode DE CoupeFonctionnement USOWhat causes blade thrust Controlling Blade ThrustHow you can reduce the chance of blade thrust Controle DES Coups DE Recul Control DEL Contragolpe DE LA HojaHow you can maintain the best control Maintenance BladeOPT10 22, 24-tooth blade Tooth blade Point OPT10Entretien Lame Comment conserver le meilleur contrôle de la machineCuál es la mejor forma de mantener el control Mantenimiento Hoja13. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes Brushcutters NotaDrive Unit BCZ2601S/BCZ2601S-CA S/N 60100101 and up Optional Blade & Accessories Engine Unit BCZ2601S/BCZ2601S-CA S/N 60100101 and up Description Part Number Qty Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada BCZ2601SW Emission Control Mesures DE Lutte ContreLES Emissions Control DE Emisiones