Zenoah BCZ2601S manual For safe operation, Working Condition, Working Circumstance

Page 8

English

5. For safe operation

1.Read this manual carefully until you completely understand and follow all safety and operating instructions.

2.Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product.

3.Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product.

4.Never allow children or anyone unable to fully understand the directions given in the manual to use the machine.

WORKING CONDITION

1.When using the product, you should wear proper clothing and protective equipment.

(1)Helmet

(2)Ear protectors

(3)Protection goggles or face protector

(4)Thick work gloves

(5)Non-slip-sole work boots

2.And you should carry with you.

(1)Attached tools and files

(2)Properly reserved fuel

(3)Spare blade or nylon string

(4)Things to notify your working area (rope, warning signs)

(5)Whistle (for collaboration or emergency)

(6)Hatchet or saw (for removal of obstacles)

3.Do not wear loose clothing, jewelry, short trousers, sandals, or go barefoot. Do not wear anything which might be caught by a moving part of the unit. Secure hair so it is above shoulder length.

WORKING CIRCUMSTANCE

1.Never start the engine inside a closed room or building. Exhaust gases contain dangerous carbon monoxide.

2.Never use the product,

a.when the ground is slippery or when you can’t maintain a steady posture.

b.At night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the working area.

c.During rain storms, during lightning storms, at times of strong or gale-force winds, or at any

8

Image 8
Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Advertencias Contenidas EN EL Manual Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOITables des matieres Contenido Specifications Parts locationEspecificaciohes Emplacement des pieces Situación de las piezasFiche technique Symbols on the machine PositionEmplacement PosiciónWorking Circumstance For safe operationWorking Condition Consignes de securite Instrucciones de seguridad Conditions DE TravailCondiciones DE Trabajo PrecaucionesWorking Plan Before Starting the EnginePlan DE Travail Plan DE TrabajoDE LA Machine Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineUtilisation DE LA Machine USO DEL Producto Demarrage DU MoteurArranque DEL Motor Maintenance If Someone ComesSI QUELQU’UN S’APPROCHE EntretienSI Alguien SE Aproxima MantenimientoTransportation Handling FuelRefill after cooling the engine Manipulation DU Carburant TransportManipulación DEL Combustible Llenar una vez que el motor se haya enfriadoSet up Assemblage Montaje Recommended Mixing Ratio Gasoline 50OIL When using RedMax/ZENOAH genuine oilFuel Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile RedMax/ZENOAH Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFor Your Engine LIFE, Avoid HOW to MIX FuelFueling the Unit Comment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirEviter Pour Prolonger LA Duree DE VIE DU Moteur Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Operation OP1 OP2 Starting EngineCutting head will start rotating upon the engine starts OP3Fonctionnement Uso Palanca del estrangulador 2 cerrarAdjusting Throttle Cable Adjusting Idling Speed OP6OP5 OP6 Stopping Engine OP3Reglage Câble D’ACCÉLÉRATEUR Ajuste Cable DEL AceleradorReglage DU Ralenti OP6 Travail DE Coupe Utilisation DE LA Tete a FILAdjusting the Line Length OP7Reglage DE LA Longeur DU FIL DE Coupe Ajuste DE LA Longitud DE LA LíneaMaintenance Maintenance ChartEntretien MantenimientoTableau D’ENTRETIEN Tabla DE MantenimientoMA1 MA2 MA3 Refilling Trimming Line MA1AIR Filter Fuel FilterEntretien Mantenimiento Filtre a AIRFiltre a Carburant Filtro DE AireReplacement Plug is a NGK CMR7H MA4Spark Plug Tightening TorqueCouple DE Serrage SilencieuxPARE-ETINCELLES LA Bujía DE Recambio Debe SER UNA Bujía NGK CMR7HMA6 Gear Case MA6Intake AIR Cooling Vent MA7Boitier DE Renvoi D’ANGLE MA6 Caja DE Engranajes MA6 Cilindro Toma de aire de refrigeración posteriorProcedures to be Performed After Every 100 Hours of USE StorageDisposal MA8Mise au rebut Eliminación Entretien MantenimientoRangement Almacenamiento Optional blade usage OPT1 OPT226~43.5 in-lbs 2.94~4.9 N.m Guard T3246-24110 Bracket HandleUtilisation de la lame optionnelle Uso de hoja opcional PAR Torsor26 43,5 pulg.-lbs 94 4,9 N.mChoose the Blade SET UP the BladeOPT3 OPT4 OPT5 Choisir LA Lame Elija LA HojaMise EN Place DE LA Lame Monte LA Hoja StandardOperation OPT6 OPT7 OPT8 OPT9Cutting Method Methode DE Coupe FonctionnementMétodo DE Corte USOHow you can reduce the chance of blade thrust Controlling Blade ThrustWhat causes blade thrust Controle DES Coups DE Recul Control DEL Contragolpe DE LA HojaMaintenance Blade OPT10How you can maintain the best control 22, 24-tooth blade Tooth blade Point OPT10Comment conserver le meilleur contrôle de la machine Cuál es la mejor forma de mantener el controlEntretien Lame Mantenimiento HojaGuide de localisation des pannes Troubleshooting guide13. Guía de localización y solución de problemas Brushcutters NotaDrive Unit BCZ2601S/BCZ2601S-CA S/N 60100101 and up Optional Blade & Accessories Engine Unit BCZ2601S/BCZ2601S-CA S/N 60100101 and up Description Part Number Qty Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Emission Control Mesures DE Lutte Contre LES EmissionsBCZ2601SW Control DE Emisiones