Manuals / Brands / Computer Equipment / Switch / Teledyne / Computer Equipment / Switch

Teledyne 10 1.2 System Specifications Table 1-1 BioOptix 10 Specifications

1 88

Download 88 pages, 4.22 Mb

BioOptix™ 10

Section 1 Introduction

1-2

1.2 System Specifications Table 1-1 lists the BioOptix 10 specifications.

Table 1-1 BioOptix 10 Specifications

Dimensions aHeight: 69 cm

Width: 72 cm

Depth: 61 cm

Weight a,b 210 kg

Power Requirement a,c

The power switch is the

disconnect device.

100 VAC ±10%, 2.0 Amps

117 VAC ±10%, 2.0 Amps

234 VAC ±10%, 1.0 Amps

Line Frequency 50 or 60 Hz

Operating Temperature a 5 to 40°C

Humidity a When connected to mains power, 95% relative humidity maximum at 5 to

40°C

Gradient Flow Rate Range 0.5 to 12 mL/min

Flow Rate Accuracy ± 5% full scale (using water)

Gradient Accuracy ± 5% full scale (using water)

Gradient Linearity ± 5% full scale (using water)

Operating Pressure 0 to 6.895 bar (0 to 100 psi)

Flow Cell Path Length 2 mm

Detector Wavelength 190 to 360 nm

Detector Noise 5 × 10-4 AU

Detector Drift 1 × 10-3 AU/hr

CE Conformity Specifications a,d Pollution Degree: 2

Installation Category: II

Maximum Altitude: 2000 meters

a. Excludes Foxy 200 Fraction Collector and Windows PC Controller. Refer to the respective manuals for these additional

specifications.

b. Dry weight of the BioOptix10, excluding connection cables, tubing, and user-supplied buffer containers.

c. Operating voltage of the BioOptix 10 is factory set.

d. Refer to the CE Declaration of Conformity, at the back of this manual, for applicable standards and test results.

Contents

Main Page Foreword Page Page DANGER Hazard Symbols Page vii Tab le of Con ten ts Section 1 Introduction Section 2 Installation Section 3 Operation BioOptix 10 Table of Contents Section 4 System Maintenance Appendix A Method Templates Appendix B Fluid Path Diagrams Appendix C Replacement Parts Lists Table of Contents List of Figures List of Tables Section 1 Introduction 1.1 Product Overview Section 1 Introduction 1-2 1.2 System Specifications Table 1-1 BioOptix 10 Specifications 1.3 System Controls and Connectors Table 1-2 BioOptix 10 Front Panel Controls Table 1-3 BioOptix 10 Left-side Connections Table 1-4 BioOptix 10 Right-side Connections Table 1-5 BioOptix 10 Rear Panel Controls and Connections Section 2 Installation 2.1 Unpacking the BioOptix 10 System 2.2 BioOptix 10 Installation Page Page Page Page Page Page Page Page Page Page Table 2-1 Tubing Color chart Page 2.3 BioOptix 10 Software Installation Table 2-2 Windows PC Minimum Requirements 2.4 BioOptix 10 System Preparation Page Page Page Section 3 Operation 3.1 Sample Preparation 3.2 Column Installation 3.3 BioOptix 10 Software 3.4 Gradients 3.5 Methods Page Page Page 3.6 Experiments Page 3.7 Running the Experiment Table 3-1 Operation Buttons Page 3.8 Post-experiment Operation Page Page Page Section 4 System Maintenance 4.1 Periodic Maintenance 4.2 Exterior Cleaning 4.3 Piston Seal Replacement Page Section 4 System Maintenance 4-4 Figure 4-3 Pump assembly components Figure 4-4 Attach seal to push rod 4.4 Deuterium Lamp Replacement Page 4.5 Troubleshooting Table 4-1 Common Problems Page Page 4.6 Service Department 4.7 How to Ship Returns Appendix A Method Templates A.1 Opening the Template Page A.2 Modifying the Template Page Appendix B Fluid Path Diagrams B.1 Fluid-type Blocks B.2 Load-type Blocks B.3 Gradient-type Blocks B.4 Pump Flush B.5 Plumbing Diagram Page Page Appendix C Replacement Parts Lists Page Page Page Page Page Page Page Page Page Page Page Page Page CE Declaration of Conformity DECLARATION OF CONFORMITY Page ( Fax: Email: Teledyne Isco One Year Limited Factory Service Warranty *