Teledyne 10 - page 25

BioOptix™ 10

Section 2 Installation

2-7

10. Connect the tubing from the column module to the pump

module. Refer to Figure 2-10.

a. Remove the two thumbscrews securing the splash

guard to the pump module. Set aside the splash guard.

Note

The tubing numbers from the column module match the num-

bers above the compression fittings on the pump module. (The

tubing is visible in Figure 2-9; the compression fittings are visi-

ble in Figure 2-10.)

b. Loosen the nut on the compression fitting, insert the

tubing fully into the fitting and finger-tighten the nut.

Then, use a wrench to tighten the nut an additional full

turn. Repeat for all ten channels.

c. Replace the splash guard so that the tubing is routed

up and over the guard.

Figure 2-10 Liquid connections

(pump module shown)

11. Slide the two modules togeth er (Refer to Figure 2-11).

Align the eight holes on the upper and side case panels,

and secure with screws.

Note

Use care to avoid damaging internal tubing and cables. Do not

pinch or crimp tubing or cables between modules.

Thumbscrew

Splash Guard

Fittings for column

module tubing

Contents

Main Page Foreword Page Page DANGER Hazard Symbols Page vii Tab le of Con ten ts Section 1 Introduction Section 2 Installation Section 3 Operation BioOptix 10 Table of Contents Section 4 System Maintenance Appendix A Method Templates Appendix B Fluid Path Diagrams Appendix C Replacement Parts Lists Table of Contents List of Figures List of Tables Section 1 Introduction 1.1 Product Overview Section 1 Introduction 1-2 1.2 System Specifications Table 1-1 BioOptix 10 Specifications 1.3 System Controls and Connectors Table 1-2 BioOptix 10 Front Panel Controls Table 1-3 BioOptix 10 Left-side Connections Table 1-4 BioOptix 10 Right-side Connections Table 1-5 BioOptix 10 Rear Panel Controls and Connections Section 2 Installation 2.1 Unpacking the BioOptix 10 System 2.2 BioOptix 10 Installation Page Page Page Page Page Page Page Page Page Page Table 2-1 Tubing Color chart Page 2.3 BioOptix 10 Software Installation Table 2-2 Windows PC Minimum Requirements 2.4 BioOptix 10 System Preparation Page Page Page Section 3 Operation 3.1 Sample Preparation 3.2 Column Installation 3.3 BioOptix 10 Software 3.4 Gradients 3.5 Methods Page Page Page 3.6 Experiments Page 3.7 Running the Experiment Table 3-1 Operation Buttons Page 3.8 Post-experiment Operation Page Page Page Section 4 System Maintenance 4.1 Periodic Maintenance 4.2 Exterior Cleaning 4.3 Piston Seal Replacement Page Section 4 System Maintenance 4-4 Figure 4-3 Pump assembly components Figure 4-4 Attach seal to push rod 4.4 Deuterium Lamp Replacement Page 4.5 Troubleshooting Table 4-1 Common Problems Page Page 4.6 Service Department 4.7 How to Ship Returns Appendix A Method Templates A.1 Opening the Template Page A.2 Modifying the Template Page Appendix B Fluid Path Diagrams B.1 Fluid-type Blocks B.2 Load-type Blocks B.3 Gradient-type Blocks B.4 Pump Flush B.5 Plumbing Diagram Page Page Appendix C Replacement Parts Lists Page Page Page Page Page Page Page Page Page Page Page Page Page CE Declaration of Conformity DECLARATION OF CONFORMITY Page ( Fax: Email: Teledyne Isco One Year Limited Factory Service Warranty *