Zenoah BCZ3001S OP5, OP6 Stopping Engine OP3, Adjusting Throttle Cable, Trimming Grass and Weeds

Page 30

English

8. Operation

OP5

.04 in

(1~2mm) (1)

OP6

(1)

■STOPPING ENGINE (OP3)

1.Release the throttle lever and run the engine for a half minute.

2.Shift the ignition switch to the STOP position.

IMPORTANT

•Except for an emergency, avoid stopping the engine while pulling the throttle lever.

■ADJUSTING THROTTLE CABLE

•The normal play is 1 or 2mm when measured at the carburetor side end. Readjust with the cable adjuster as required. (OP5)

(1) cable adjuster

■ADJUSTING IDLING SPEED (OP6)

1.When the engine tends stop frequently at idling mode, turn the adjusting screw clockwise.

2.When the cutting head keeps rotating after releasing the trigger, turn the adjusting screw counter- clockwise.

(1) idle adjusting screw

NOTE

•Warm up the engine before adjusting the idling speed.

■CUTTING WORK (LINE HEAD USAGE)

WARNING

1.Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury.

2.Keep the cutting attachment guard in place at all times when the unit is operated.

TRIMMING GRASS AND WEEDS

•Always remember that the TIP of the line does cutting. You will achieve better results by not crowding the line into the cutting area. Allow the unit

30

Image 30

Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOI Tables des matieres ContenidoAdvertencias Contenidas EN EL Manual Parts location BCZ3001SWBCZ3001S-CA BCZ3001SW-CA Emplacement des pieces Situación de las piezas BCZ3001S-CASpecifications Dry weightFiche technique EspecificaciohesSymbols on the machine PositionEmplacement PosiciónFor safe operation Working ConditionWorking Circumstance Condiciones DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail PrecaucionesWorking Plan Before Starting the EngineDE LA Machine Plan DE TravailPlan DE Trabajo Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineCut only materials recommended by Demarrage DU Moteur Arranque DEL MotorUtilisation DE LA Machine USO DEL Producto Maintenance If Someone ComesSI Alguien SE Aproxima SI QUELQU’UN S’APPROCHEEntretien MantenimientoRefill after cooling the engine For use with the RedMax productHandling Fuel TransportationLlenar una vez que el motor se haya enfriado Manipulation DU CarburantManipulación DEL Combustible TransportSet up Assemblage Montaje When using RedMax/ZENOAH genuine oil FuelRecommended Mixing Ratio Gasoline 50OIL Lors de l’utilisation de la véritable huile RedMax/ZENOAH Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteHOW to MIX Fuel Fueling the UnitFor Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Cutting head will start rotating upon the engine starts OperationOP1 OP2 Starting Engine OP3Fonctionnement Uso Palanca del estrangulador 2 cerrarOP5 Adjusting Throttle CableAdjusting Idling Speed OP6 OP6 Stopping Engine OP3Reglage DU Ralenti OP6 Reglage Câble D’ACCÉLÉRATEURAjuste Cable DEL Acelerador Travail DE Coupe Utilisation DE LA Tete DE FILAdjusting the Line Length OP7Reglage DE LA Longeur DU FIL DE Coupe Ajuste DE LA Longitud DE LA LíneaMaintenance Maintenance ChartTableau D’ENTRETIEN EntretienMantenimiento Tabla DE MantenimientoAIR Filter MA1 MA2 MA3Refilling Trimming Line MA1 Fuel FilterFiltre a Carburant Entretien MantenimientoFiltre a AIR Filtro DE AireSpark Plug Replacement Plug is a NGK CMR7HMA4 Tightening TorquePARE-ETINCELLES Couple DE SerrageSilencieux LA Bujía DE Recambio Debe SER UNA Bujía NGK CMR7HIntake AIR Cooling Vent MA6Angle Transmission MA6 MA7Transmission D’ANGLE MA6 Transmisión DEL Ángulo MA6 Cilindro Toma de aire de refrigeración posteriorDisposal Procedures to be Performed After Every 100 Hours of USEStorage MA8Entretien Mantenimiento Rangement AlmacenamientoMise au rebut Eliminación Optional blade usage OPT1 OPT2Bracket Handle 26 43,5 pulg.-lbs Utilisation de la lame optionnelle Uso de hoja opcionalCouple DE Serrage PAR Torsor Moyeu 3583-14101 Poignée en J 6367-14200SET UP the Blade OPT3 OPT4 OPT5Choose the Blade Choisir LA Lame Elija LA HojaMise EN Place DE LA Lame Monte LA Hoja OPT6 OPT7 OPT8 OPT9 Cutting MethodOperation Método DE Corte Methode DE CoupeFonctionnement USOControlling Blade Thrust What causes blade thrustHow you can reduce the chance of blade thrust Controle DES Coups DE Recul Control DEL Contragolpe DE LA HojaHow you can maintain the best control Maintenance BladeOPT10 22, 24-tooth blade Tooth blade Point OPT10Entretien Lame Comment conserver le meilleur contrôle de la machineCuál es la mejor forma de mantener el control Mantenimiento HojaTroubleshooting guide 13. Guía de localización y solución de problemasGuide de localisation des pannes Brushcutters NotaDrive Unit BCZ3001S/BCZ3001S-CA S/N 60100101 and up Optional Blade & Accessories Drive Unit BCZ3001SW/BCZ3001SW-CA S/N 60100101 and up Optional Blade Parts list Special Tools Part Number Description QtyManufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Mesures DE Lutte Contre LES Emissions Emission ControlBCZ3001S/BCZ3001SW Control DE Emisiones