Zenoah BCZ3001S manual Angle Transmission MA6, Intake AIR Cooling Vent, MA7

Page 40

MA6

English

9. Maintenance

■ANGLE TRANSMISSION (MA6)

•The reduction gears are lubricated by multipurpose, lithium-based grease in the angle transmission. Supply new grease every 25 hours of use or more often depending on the job condition.

•Remove the side bolt in angle transmission opposite of grease nipple before installing new grease to arrange for old grease to exit.

■INTAKE AIR COOLING VENT

WARNING

•Never touch the cylinder, muffler, or spark plugs with your bare hands immediately after stopping the engine. The engine can become very hot when in operation, and doing so could result in severe burns.

•When checking the machine to make sure that it is okay before using it, check the area around the muffler and remove any wood chips or leaves which have attached themselves to the brushcutter. Failing to do so could cause the muffler to become overheated, and that this in turn could cause the engine to catch on fire. Always make sure that the muffler is clean and free of wood chips, leaves, and other waste before use.

•Check the intake air cooling vent and the area around the cylinder cooling fins after every 25 hours of use for blockage, and remove any waste which has attached itself to the brushcutter. Note that it is necessary to remove the engine cover shown in (MA7) in order to be able to view the upper part of the cylinder.

MA7

(1)

(2)

IMPORTANT

•If waste gets stuck and causes blockage around the intake air cooling vent or between the cylinder fins, it may cause the engine to overheat, and that in turn may cause mechanical failure on the part of the brushcutter. (MA7)

(1)cylinder

(2)intake air cooling vent (back)

40

Image 40

Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual BCZ3001SW Parts locationBCZ3001S-CA BCZ3001SW-CA Emplacement des pieces Situación de las piezas BCZ3001S-CASpecifications Dry weightFiche technique EspecificaciohesSymbols on the machine PositionEmplacement PosiciónWorking Condition For safe operationWorking Circumstance Consignes de securite Instrucciones de seguridad Conditions DE TravailCondiciones DE Trabajo PrecaucionesWorking Plan Before Starting the EnginePlan DE Travail Plan DE TrabajoDE LA Machine Avant DE Mettre LE Moteur EN MarcheStarting the Engine Using the ProductCut only materials recommended by Arranque DEL Motor Demarrage DU MoteurUtilisation DE LA Machine USO DEL Producto Maintenance If Someone ComesSI QUELQU’UN S’APPROCHE EntretienSI Alguien SE Aproxima MantenimientoFor use with the RedMax product Handling FuelRefill after cooling the engine TransportationManipulation DU Carburant Manipulación DEL CombustibleLlenar una vez que el motor se haya enfriado TransportSet up Assemblage Montaje Fuel When using RedMax/ZENOAH genuine oilRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile RedMax/ZENOAH Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFueling the Unit HOW to MIX FuelFor Your Engine LIFE, Avoid Comment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirEviter Pour Prolonger LA Duree DE VIE DU Moteur Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Operation OP1 OP2 Starting EngineCutting head will start rotating upon the engine starts OP3Fonctionnement Uso Palanca del estrangulador 2 cerrarAdjusting Throttle Cable Adjusting Idling Speed OP6OP5 OP6 Stopping Engine OP3Reglage Câble D’ACCÉLÉRATEUR Ajuste Cable DEL AceleradorReglage DU Ralenti OP6 Travail DE Coupe Utilisation DE LA Tete DE FILAdjusting the Line Length OP7Reglage DE LA Longeur DU FIL DE Coupe Ajuste DE LA Longitud DE LA LíneaMaintenance Maintenance ChartEntretien MantenimientoTableau D’ENTRETIEN Tabla DE MantenimientoMA1 MA2 MA3 Refilling Trimming Line MA1AIR Filter Fuel FilterEntretien Mantenimiento Filtre a AIRFiltre a Carburant Filtro DE AireReplacement Plug is a NGK CMR7H MA4Spark Plug Tightening TorqueCouple DE Serrage SilencieuxPARE-ETINCELLES LA Bujía DE Recambio Debe SER UNA Bujía NGK CMR7HMA6 Angle Transmission MA6Intake AIR Cooling Vent MA7Transmission D’ANGLE MA6 Transmisión DEL Ángulo MA6 Cilindro Toma de aire de refrigeración posteriorProcedures to be Performed After Every 100 Hours of USE StorageDisposal MA8Rangement Almacenamiento Entretien MantenimientoMise au rebut Eliminación OPT1 OPT2 Optional blade usageBracket Handle Utilisation de la lame optionnelle Uso de hoja opcional Couple DE Serrage PAR Torsor26 43,5 pulg.-lbs Moyeu 3583-14101 Poignée en J 6367-14200OPT3 OPT4 OPT5 SET UP the BladeChoose the Blade Elija LA Hoja Choisir LA LameMise EN Place DE LA Lame Monte LA Hoja Cutting Method OPT6 OPT7 OPT8 OPT9Operation Methode DE Coupe FonctionnementMétodo DE Corte USOWhat causes blade thrust Controlling Blade ThrustHow you can reduce the chance of blade thrust Controle DES Coups DE Recul Control DEL Contragolpe DE LA HojaMaintenance Blade OPT10How you can maintain the best control 22, 24-tooth blade Tooth blade Point OPT10Comment conserver le meilleur contrôle de la machine Cuál es la mejor forma de mantener el controlEntretien Lame Mantenimiento Hoja13. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes Brushcutters NotaDrive Unit BCZ3001S/BCZ3001S-CA S/N 60100101 and up Optional Blade & Accessories Drive Unit BCZ3001SW/BCZ3001SW-CA S/N 60100101 and up Optional Blade Parts list Special Tools Part Number Description QtyManufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Emission Control BCZ3001S/BCZ3001SWMesures DE Lutte Contre LES Emissions Control DE Emisiones