Troy-Bilt 12212, 12211 owner manual Introduction, BREAK-IN Operation, Starting and Stopping Engine

Page 16

Section

4Operation

WARNING

Before operating your machine, care- fully read and understand all safety (Section 1), controls (Section 3) and operating instructions (Section 4) in this Manual, in the separate Engine Owner’s Manual, and on the decals on the machine.

Failure to follow these instructions can result in serious personal injury.

 

Reverse Clutch

Throttle Lever

Wheel Gear Lever

 

Forward Clutch Lever (also on right-side)

Handlebar Height

 

Adjustment Handle

Depth Regulator Lever

 

Figure 4-1: Location of main tiller controls.

INTRODUCTION

Read this Section of the manual thor- oughly before you start the engine. Then, take the time to familiarize yourself with the basic operation of the tiller before using it in the garden.

Find an open, level area and practice using the tiller controls without the tines engaging the soil (put tines in “travel” setting). Only after you’ve become com- pletely familiar with the tiller should you begin using it in the garden.

BREAK-IN OPERATION

Perform the following maintenance during the first hours of new operation (see “Maintenance” in this manual and in the Engine Owner’s Manual).

1.Change engine oil after first two (2) hours of new engine operation.

2.Check for loose or missing hardware on unit. Tighten or replace as needed.

3.Check transmission gear oil level after first two (2) hours of operation.

4.Check tension on forward drive belt after first two (2) hours of operation.

STARTING AND STOPPING

THE ENGINE

Pre-Start Checklist:

Make the following checks and perform the following services before starting the engine.

1.Read the “Safety” and “Controls” Sec- tions in this Manual. Read the separate Engine Owner’s Manual provided by the engine manufacturer.

2.Check unit for loose or missing hard- ware. Service as required.

3.Check engine oil level. See Engine Owner’s Manual.

4.Check that all safety guards and covers are in place.

5.Check air cleaner and engine cooling system. See Engine Owner’s Manual.

6.Attach spark plug wire to spark plug.

DANGER

GASOLINE IS HIGHLY FLAMMABLE AND ITS VAPORS ARE EXPLOSIVE.

Follow gasoline safety rules in this manual (see Section 1) and in the separate Engine Owner’s Manual.

Failure to follow gasoline safety instructions can result in serious per- sonal injury and property damage.

7.Fill the fuel tank with gasoline accord- ing to the directions in the separate Engine Owner’s Manual. Follow all instructions and safety rules carefully.

CAUTION

To help prevent serious personal injury or damage to equipment:

Before starting engine, put Wheel Gear Lever in ENGAGE position.

Before starting engine, put Forward Clutch Levers and Reverse Clutch Control in neutral (disengaged) posi- tions by releasing controls.

Never run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monox- ide, an odorless and deadly gas.

Avoid engine muffler and nearby areas.

Temperatures in these areas may exceed 150oF.

16

Image 16
Contents 7HP Pony REAR-TINE Tiller Recoil Start Model shownSee Back Cover for Customer Service information Safety Exercise caution to avoid slipping or fallingKeep children and pets away Use slower engine speedsOperating Symbols To Avoid Serious InjuryInspect unit IntroductionAttach Handlebars Screw the height adjustment handle Attach Forward Clutch RodAttach Reverse Clutch Control Hairpin CotterReinstall and hand-tighten the oil fill plug N Check Gear Oil Level in TransmissionSelect the proper hole in the clutch If the gap is incorrectAttach Engine Throttle Lever Check Air Pressure in TiresAdd Motor Oil to Engine Attach Wheel Gear LeverBattery Activation and Charging Check Hardware for TightnessAttach Battery Cables and Vent Tube Install BatteryConnect Wiring Harness KeyswitchWheel Gear Lever Forward ClutchTo Operate the Forward Clutch EngageHandlebar Height Adjustment To Adjust the Handlebar HeightReverse Clutch Depth RegulatorEngine Throttle Lever Electric Start Keyswitch electric start modelStop on recoil start model only Stop Stops the engine Pre-Start Checklist IntroductionBREAK-IN Operation Starting and Stopping EngineOperating the Tiller Starting the EngineStopping the Engine Stop Stop positionKeyswitch to OFF to stop the engine Turning the Tiller AroundFor forward motion of the wheels and tines For reverse motion of the wheels and tinesLet the tiller do the work Tilling depthsAvoid tilling soggy, wet soil Avoid making footprintsTilling across slopes without using terraces Clearing the tinesTilling on slopes Tilling up and down slopesPower Composting Loading and Unloading TillerRequired Maintenance Schedule ProcedureTiller Lubrication EveryTransmission Gear OIL Service Check HardwareCheck Tire Pressure Check for OIL LeaksEngine Cleaning Engine OIL ServiceAIR Cleaner Service CARBURETOR/GOVERNOR Control AdjustmentsOFF Season Storage Wheel Gear Cable AdjustmentBolo Tines Checking and Adjusting Tension on the Drive Belts Reinstall the belt cover and secure it with the two nutsCutting Edge Tine Threads Forward Drive Belt Removal and Installation Installing the Forward Drive BeltRemoving the Forward Drive Belt Reverse Drive Belt Removal and Installation Removing the Reverse Drive BeltBattery Maintenance Installing the Reverse Drive BeltReconnect the reverse cable wire to the Z-fitting Q, Figure Battery Care in ServiceTiller Weight Transmission Gear OIL SpecificationsTiller Length Tiller WidthTroubleshooting Problem Possible Cause CorrectionModels 12211 HOOD, Bracket and Depth RegulatorPart Description QTYHandlebar Assembly and Control Levers Bellcrank See PgParts List ENGINE, Support BRACKETS, PULLEYS, BELTS, Belt Cover Part Description QTY Forward Idler Assembly 9621 Drive SHAFT, Input Pinion Shaft and Gear Assemblies Input Pinion Shaft & Gear AssemblyMain Drive Shaft Wheel SHAFT, Eccentric Shaft and Tiller Shaft Assemblies Bolo TINES, Wheels Two ea. Refs 1733398 Hex Locknut, 3/8-16 1982612HILLER/FURROWER Attachment Electric Start Assembly 96512 Battery, 12 Volt, 9 Amp Incl 9462 Bumper Attachment ROW Marker Attachment1904522001 Models 12211 ROW Marker Attachment & Bumper AttachmentDescription QTY Row Marker AttachmentWarranty Service Replacement PartsEngine Service and Repair Owner Registration Card