Troy-Bilt 12211, 12212 Engine Throttle Lever, Electric Start Keyswitch electric start model

Page 15

Section 3: Features and Controls

 

3

4

 

1

3

 

2

 

 

 

 

1

2

4

 

 

 

Figure 3-4: Handlebar height slots and clutch swivel plate holes.

ENGINE CONTROLS

Refer to the engine manufacturer’s Engine Owner’s Manual (included in the tiller lit- erature package) to identify the controls on your engine. The following two con- trols are located on the tiller.

Engine Throttle Lever

The Throttle Lever (G, Figure 3-5) is used to regulate the engine speed. On the recoil start model only, it is also used to stop the engine (on the electric start model, the electric start keyswitch is used to stop the engine). The throttle settings are shown below.

IMPORTANT: See “Starting and Stopping the Engine” in the “Operation” Section for detailed engine starting and stopping instructions.

FAST - Use for most tilling and cultivating projects.

START - Use when starting engine.

SLOW - Use when idling engine or when slower tilling and cultivating speeds are needed.

G

Figure 3-5: Engine Throttle Lever.

Electric Start Keyswitch (electric start model)

The ignition keyswitch on the electric start model (H, Figure 3-6) is used to start and stop the engine. The keyswitch settings are described below.

IMPORTANT: See “Starting and Stopping the Engine” in the “Operation” Section for detailed engine starting and stopping instructions.

OFF - Stops engine.

RUN - After starting, key returns to run position.

START - Starts engine. Release key when engine starts (avoid cranking engine for longer than 15 seconds at a time).

STOP (on recoil start model only) - STOP Stops the engine.

H

Figure 3-6: Electric start keyswitch.

15

Image 15
Contents Recoil Start Model shown 7HP Pony REAR-TINE TillerSee Back Cover for Customer Service information Exercise caution to avoid slipping or falling SafetyUse slower engine speeds Keep children and pets awayTo Avoid Serious Injury Operating SymbolsIntroduction Inspect unitAttach Handlebars Hairpin Cotter Screw the height adjustment handleAttach Forward Clutch Rod Attach Reverse Clutch ControlIf the gap is incorrect Reinstall and hand-tighten the oil fill plug NCheck Gear Oil Level in Transmission Select the proper hole in the clutchAttach Wheel Gear Lever Attach Engine Throttle LeverCheck Air Pressure in Tires Add Motor Oil to EngineCheck Hardware for Tightness Battery Activation and ChargingInstall Battery Attach Battery Cables and Vent TubeKeyswitch Connect Wiring HarnessEngage Wheel Gear LeverForward Clutch To Operate the Forward ClutchDepth Regulator Handlebar Height AdjustmentTo Adjust the Handlebar Height Reverse ClutchElectric Start Keyswitch electric start model Engine Throttle LeverStop on recoil start model only Stop Stops the engine Starting and Stopping Engine Pre-Start ChecklistIntroduction BREAK-IN OperationStop Stop position Operating the TillerStarting the Engine Stopping the EngineFor reverse motion of the wheels and tines Keyswitch to OFF to stop the engineTurning the Tiller Around For forward motion of the wheels and tinesAvoid making footprints Let the tiller do the workTilling depths Avoid tilling soggy, wet soilTilling up and down slopes Tilling across slopes without using terracesClearing the tines Tilling on slopesLoading and Unloading Tiller Power CompostingEvery Required Maintenance ScheduleProcedure Tiller LubricationCheck for OIL Leaks Transmission Gear OIL ServiceCheck Hardware Check Tire PressureCARBURETOR/GOVERNOR Control Adjustments Engine CleaningEngine OIL Service AIR Cleaner ServiceWheel Gear Cable Adjustment OFF Season StorageBolo Tines Reinstall the belt cover and secure it with the two nuts Checking and Adjusting Tension on the Drive BeltsCutting Edge Tine Threads Installing the Forward Drive Belt Forward Drive Belt Removal and InstallationRemoving the Forward Drive Belt Removing the Reverse Drive Belt Reverse Drive Belt Removal and InstallationBattery Care in Service Battery MaintenanceInstalling the Reverse Drive Belt Reconnect the reverse cable wire to the Z-fitting Q, FigureTiller Width Tiller WeightTransmission Gear OIL Specifications Tiller LengthProblem Possible Cause Correction TroubleshootingQTY Models 12211HOOD, Bracket and Depth Regulator Part DescriptionBellcrank See Pg Handlebar Assembly and Control LeversParts List ENGINE, Support BRACKETS, PULLEYS, BELTS, Belt Cover Part Description QTY Forward Idler Assembly 9621 Input Pinion Shaft & Gear Assembly Drive SHAFT, Input Pinion Shaft and Gear AssembliesMain Drive Shaft Wheel SHAFT, Eccentric Shaft and Tiller Shaft Assemblies Two ea. Refs 1733398 Hex Locknut, 3/8-16 1982612 Bolo TINES, WheelsHILLER/FURROWER Attachment Electric Start Assembly 96512 Battery, 12 Volt, 9 Amp Incl 9462 ROW Marker Attachment Bumper Attachment1904522001 Row Marker Attachment Models 12211ROW Marker Attachment & Bumper Attachment Description QTYOwner Registration Card Warranty ServiceReplacement Parts Engine Service and Repair