Troy-Bilt 12212, 12211 Bolo TINES, Wheels, Two ea. Refs 1733398 Hex Locknut, 3/8-16 1982612

Page 42

PARTS LIST

Models 12211 and 12212

BOLO TINES, WHEELS

9

1310

13

NOTE 1: Custom Tilling Tines are available for your tiller. These are special hard-faced tines that are thicker than standard tines.

IMPORTANT: Left and right sides of tiller are determined by standing in operator position and facing direc- tion of forward travel.

REF.

PART

 

 

No.

No.

DESCRIPTION

QTY.

1

1100043

Hex Hd. Screw, 3/8-16 x 1-1/4*

16

21270-2A Bolo Tine-single. Right hand tine used on left side of tiller. (Incl.

 

 

two ea. Refs. 1 and 3)

8

3

1733398

Hex Locknut, 3/8-16

18

5

1982612

Hex Hd. Screw, 3/8-16 x 2, Grade 8 ....

2

71270-1A Bolo Tine-single. Left hand tine used on right side of tiller. (Incl.

 

two ea. Refs. 1 and 3)

8

8

1902154010 Tine Holder. For left and right sides ....

2

--1901118 Bolo Tine Replacement Set (Incl. eight ea. right hand and left hand tines,

 

 

and sixteen ea. Refs. 1 and 3)

1

--

2475-1

Custom Tilling Bolo Tine, Left hand

 

 

 

tine (see Note 1 above)

8

REF.

PART

 

 

No.

No.

DESCRIPTION

QTY.

--

2475-2

Custom Tilling Bolo Tine, Right hand

 

 

 

tine (see Note 1 above)

8

--

10802

Custom Tilling Bolo Tine Replacement

 

 

 

Set (Incl. eight ea. right hand and

 

 

 

left hand custom tines, and sixteen

 

 

 

each of Refs. 1 and 3)

1

9

2706-01

Wheel and Tire Assy., left side,

 

 

 

4.10 x 6 tire on 6” wheel (A)(B)

1

10

2706-02

Wheel & Tire Assy., right side,

 

 

 

4.10 x 6 tire on 6” wheel (A)(B)

1

11

9380

Clevis Pin, .312 x 1-3/4

2

12

9338

Hitch Pin

2

13

1917487

Wheel and Tire Assembly (C)(D)

2

* Specify GRADE 5 if ordering part locally.

(A)

For Model 12211 – S/N 122111100101-122111199999

 

(B)

For Model 12212 – S/N 122121100101-122121199999

 

(C)

For Model 12211 – S/N 122111200101-122111299999

42

(D)

For Model 12212 – S/N 122121200101-122121299999

Image 42
Contents 7HP Pony REAR-TINE Tiller Recoil Start Model shownSee Back Cover for Customer Service information Safety Exercise caution to avoid slipping or fallingKeep children and pets away Use slower engine speedsOperating Symbols To Avoid Serious InjuryIntroduction Inspect unitAttach Handlebars Attach Reverse Clutch Control Screw the height adjustment handleAttach Forward Clutch Rod Hairpin CotterSelect the proper hole in the clutch Reinstall and hand-tighten the oil fill plug NCheck Gear Oil Level in Transmission If the gap is incorrectAdd Motor Oil to Engine Attach Engine Throttle LeverCheck Air Pressure in Tires Attach Wheel Gear LeverBattery Activation and Charging Check Hardware for TightnessAttach Battery Cables and Vent Tube Install BatteryConnect Wiring Harness KeyswitchTo Operate the Forward Clutch Wheel Gear LeverForward Clutch EngageReverse Clutch Handlebar Height AdjustmentTo Adjust the Handlebar Height Depth RegulatorElectric Start Keyswitch electric start model Engine Throttle LeverStop on recoil start model only Stop Stops the engine BREAK-IN Operation Pre-Start ChecklistIntroduction Starting and Stopping EngineStopping the Engine Operating the TillerStarting the Engine Stop Stop positionFor forward motion of the wheels and tines Keyswitch to OFF to stop the engineTurning the Tiller Around For reverse motion of the wheels and tinesAvoid tilling soggy, wet soil Let the tiller do the workTilling depths Avoid making footprintsTilling on slopes Tilling across slopes without using terracesClearing the tines Tilling up and down slopesPower Composting Loading and Unloading TillerTiller Lubrication Required Maintenance ScheduleProcedure EveryCheck Tire Pressure Transmission Gear OIL ServiceCheck Hardware Check for OIL LeaksAIR Cleaner Service Engine CleaningEngine OIL Service CARBURETOR/GOVERNOR Control AdjustmentsWheel Gear Cable Adjustment OFF Season StorageBolo Tines Reinstall the belt cover and secure it with the two nuts Checking and Adjusting Tension on the Drive BeltsCutting Edge Tine Threads Installing the Forward Drive Belt Forward Drive Belt Removal and InstallationRemoving the Forward Drive Belt Reverse Drive Belt Removal and Installation Removing the Reverse Drive BeltReconnect the reverse cable wire to the Z-fitting Q, Figure Battery MaintenanceInstalling the Reverse Drive Belt Battery Care in ServiceTiller Length Tiller WeightTransmission Gear OIL Specifications Tiller WidthTroubleshooting Problem Possible Cause CorrectionPart Description Models 12211HOOD, Bracket and Depth Regulator QTYHandlebar Assembly and Control Levers Bellcrank See PgParts List ENGINE, Support BRACKETS, PULLEYS, BELTS, Belt Cover Part Description QTY Forward Idler Assembly 9621 Input Pinion Shaft & Gear Assembly Drive SHAFT, Input Pinion Shaft and Gear AssembliesMain Drive Shaft Wheel SHAFT, Eccentric Shaft and Tiller Shaft Assemblies Bolo TINES, Wheels Two ea. Refs 1733398 Hex Locknut, 3/8-16 1982612HILLER/FURROWER Attachment Electric Start Assembly 96512 Battery, 12 Volt, 9 Amp Incl 9462 ROW Marker Attachment Bumper Attachment1904522001 Description QTY Models 12211ROW Marker Attachment & Bumper Attachment Row Marker AttachmentEngine Service and Repair Warranty ServiceReplacement Parts Owner Registration Card