Troy-Bilt 12211, 12212 owner manual Battery, 12 Volt, 9 Amp Incl 9462

Page 45

Models 12211 and 12212	PARTS LIST
	ELECTRIC START ASSEMBLY

REF.	PART
No.	No.	DESCRIPTION	QTY.
1	96512	Battery, 12 Volt, 9 Amp (Incl.
		Ref. 7)	1
2	9462	Battery Cap (yellow)	A/R
2A	9248	Battery Cap (white)	A/R
3	9009	Vent Tube	1
4	1475	Shield, Vent Tube (hard plastic)	1
5	9224	Clamp	1
6	9552	Hex Flange Screw, Self-Threading,
		1/4-20 x 1/2*	3
7	11361	Battery Hardware Kit – Includes two
		M6 x 11mm Bolts and two M6
		Nuts (metric sizes)	1

81908112 Ignition Switch (Incl. two ignition keys [Ref. 11], one lockwasher and one

		nut (lockwasher and nut not
		available separately)	1
9	1904570	Battery Hold-Down Clamp/Switch
		Mounting Plate Assy. (Incl. Ref.10)	1
10	1904548	Decal, Ignition Switch	1
11	96520	Ignition Key (pair)	1
12	96509	Battery Cable	2
13	96510	Cable (solenoid to starter motor)	1

141908118 Wire Harness Assy. (available as complete assembly only). Incl. wire assy. w/connector to large solenoid stud (red wire); wire assy. w/connector to small solenoid stud (red wire); wire assy. w/connector to solenoid

grounding screw (red wire); wire
assy w/connector to engine ground
shut-off (green wire); plastic
protector tube; wire terminal	1

REF.	PART
No.	No.	DESCRIPTION	QTY.
15	97020	Boot, Insulating	2
16	96514	Solenoid (Incl. nuts and washers
		for cables and wires)	1
17	20837	Battery Bracket	1
18	1186023	Round Hd. Screw, Square Neck,
		1/4-20 x 1-1/4	2
19	1186331	Hex Flange Screw, 5/16-18 x 1*	2
20	1177548	Lockwasher, External Tooth	2
21	1186389	Hex Locknut, 1/4-20	2
22	1100242	Lockwasher, 5/16	2
23	1186211	Hex Nut, 5/16-24	2
24	9853	Hex Locknut, #10-32	1
25	--	Lockwasher, #10 (not available
		from factory)	1
26	--	Hex Nut, #10-24 (not available
		from factory)	1
27	1901894	Recharge Wire Assembly	1
28	9218	Clip (holds recharging line)	1
29	9265	Plastic Wire Tie	1
30	9202	Plastic Wire Tie	1
31	1901202	Cable (ground wire to starter
		motor bracket)	1
32	1917262	Ground Wire Assy. (shut off)	1

*Specify GRADE 5 if ordering part locally. A/R - As Required

45

Image 45

Contents Recoil Start Model shown 7HP Pony REAR-TINE TillerSee Back Cover for Customer Service information Exercise caution to avoid slipping or falling SafetyUse slower engine speeds Keep children and pets awayTo Avoid Serious Injury Operating SymbolsIntroduction Inspect unitAttach Handlebars Attach Forward Clutch Rod Screw the height adjustment handleAttach Reverse Clutch Control Hairpin CotterCheck Gear Oil Level in Transmission Reinstall and hand-tighten the oil fill plug NSelect the proper hole in the clutch If the gap is incorrectCheck Air Pressure in Tires Attach Engine Throttle LeverAdd Motor Oil to Engine Attach Wheel Gear LeverCheck Hardware for Tightness Battery Activation and ChargingInstall Battery Attach Battery Cables and Vent TubeKeyswitch Connect Wiring HarnessForward Clutch Wheel Gear LeverTo Operate the Forward Clutch EngageTo Adjust the Handlebar Height Handlebar Height AdjustmentReverse Clutch Depth RegulatorElectric Start Keyswitch electric start model Engine Throttle LeverStop on recoil start model only Stop Stops the engine Introduction Pre-Start ChecklistBREAK-IN Operation Starting and Stopping EngineStarting the Engine Operating the TillerStopping the Engine Stop Stop positionTurning the Tiller Around Keyswitch to OFF to stop the engineFor forward motion of the wheels and tines For reverse motion of the wheels and tinesTilling depths Let the tiller do the workAvoid tilling soggy, wet soil Avoid making footprintsClearing the tines Tilling across slopes without using terracesTilling on slopes Tilling up and down slopesLoading and Unloading Tiller Power CompostingProcedure Required Maintenance ScheduleTiller Lubrication EveryCheck Hardware Transmission Gear OIL ServiceCheck Tire Pressure Check for OIL LeaksEngine OIL Service Engine CleaningAIR Cleaner Service CARBURETOR/GOVERNOR Control AdjustmentsWheel Gear Cable Adjustment OFF Season StorageBolo Tines Reinstall the belt cover and secure it with the two nuts Checking and Adjusting Tension on the Drive BeltsCutting Edge Tine Threads Installing the Forward Drive Belt Forward Drive Belt Removal and InstallationRemoving the Forward Drive Belt Removing the Reverse Drive Belt Reverse Drive Belt Removal and InstallationInstalling the Reverse Drive Belt Battery MaintenanceReconnect the reverse cable wire to the Z-fitting Q, Figure Battery Care in ServiceTransmission Gear OIL Specifications Tiller WeightTiller Length Tiller WidthProblem Possible Cause Correction TroubleshootingHOOD, Bracket and Depth Regulator Models 12211Part Description QTYBellcrank See Pg Handlebar Assembly and Control LeversParts List ENGINE, Support BRACKETS, PULLEYS, BELTS, Belt Cover Part Description QTY Forward Idler Assembly 9621 Input Pinion Shaft & Gear Assembly Drive SHAFT, Input Pinion Shaft and Gear AssembliesMain Drive Shaft Wheel SHAFT, Eccentric Shaft and Tiller Shaft Assemblies Two ea. Refs 1733398 Hex Locknut, 3/8-16 1982612 Bolo TINES, WheelsHILLER/FURROWER Attachment Electric Start Assembly 96512 Battery, 12 Volt, 9 Amp Incl 9462 ROW Marker Attachment Bumper Attachment1904522001 ROW Marker Attachment & Bumper Attachment Models 12211Description QTY Row Marker AttachmentReplacement Parts Warranty ServiceEngine Service and Repair Owner Registration Card