Genie Z-34, Z-22IC manual Fall Hazards

Page 6

Operator's Manual

Fourth Edition • First Printing

 

 

 

 

 

 

SAFETY RULES

Do not place or attach overhanging loads to any part of this machine.

Do not place ladders or scaffolds in the platform or against any part of this machine.

Do not transport tools and materials unless they are evenly distributed and can be safely handled by person(s) in the platform.

Do not use the machine on a moving or mobile surface or vehicle.

Do not modify or alter an aerial work platform without prior written permission from the manufacturer. Mounting attachments for holding tools or other materials onto the platform, toeboards or guard rail system can increase the weight in the platform and the surface area of the platform or the load.

Be sure all tires are in good condition, air-filled tires are properly inflated and lug nuts are properly tightened.

Do not use the machine as a crane.

Do not push the machine or other objects with the boom.

Do not contact adjacent structures with the boom.

Do not tie the boom or platform to adjacent structures.

Do not place loads outside the platform perimeter.

Fall Hazards

Occupants must wear a safety belt or harness and comply with applicable governmental regulations. Attach the lanyard to the anchor provided in the platform.

Do not sit, stand or climb on the platform guard rails. Maintain a firm footing on the platform floor at all times.

Do not climb down from the platform when raised.

Keep the platform floor clear of debris.

Lower the platform entry mid-rail or close the entry gate before operating.

4

Z-34/22 IC

Part No. 1000048

Image 6
Contents Operator’s Manual Contents Contact usSafety Rules Do Not Operate UnlessElectrocution Hazards Tip-over HazardsCSA Fall Hazards Collision Hazards Component Damage HazardDamaged Machine Hazards Battery Safety Burn HazardsExplosion and Fire Hazards Bodily Injury HazardDecal Legend Controls Platform Control PanelGround Control Panel ControlsOperators Manual Pre-operation Inspection FundamentalsPre-operation Inspection Observe and Obey MaintenanceMaintenance Symbols Legend Check the Hydraulic Oil LevelCheck the Engine Oil Level Check the BatteriesScheduled Maintenance Check the Tire PressureFunction Tests Test the Machine Functions At the Ground ControlsTest the Emergency Stop Test the Tilt SensorTest the Horn Test the Foot SwitchAt the Platform Controls Test Machine FunctionsTest the Drive Enable System Test Drive and BrakingTest Limited Drive Speed Test the Lift/Drive Select Function if equippedWorkplace Inspection Workplace InspectionOperating Instructions Only use the machine as it was intendedAuxiliary Controls Starting the EngineEmergency Stop Operation from GroundOperation from Platform To SteerTo Drive Driving on a slope To determine the slope gradeDrive Speed Select Drive EnableGenerator if equipped Engine Idle Select rpmFall Protection Platform Overload Indicator Light if equippedMachine Not Level Indicator Light if equipped After Each UseDecals Inspection for Decals with WordsGround Controls Side Chassis Platform Engine SideInspection for Decals with Symbols Ground Controls Side Chassis Platform Free-wheel Configuration for Winching Transport and Lifting InstructionsSecuring to Truck or Trailer for Transit Securing the ChassisSecuring the Platform Lifting Instructions Specifications 34/22 2WD IndustrialSpecifications Range of Motion Distributed By

Z-34, Z-22IC specifications

The Genie Z-34 and Z-22IC are innovative models in the aerial work platform category known for their versatility and efficiency. These machines are particularly popular for their reach, maneuverability, and suitability for various applications, from construction sites to maintenance tasks.

The Genie Z-34 boasts a working height of 40 feet, allowing operators to access high-reaching areas safely and efficiently. It features a robust platform capacity of 500 lbs, making it capable of handling multiple workers and equipment simultaneously. The Z-34 is designed with advanced drive and lifting systems that ensure smooth operation, even in challenging environments. Its compact design allows it to navigate tight spaces and congested job sites with ease, making it an ideal choice for urban projects.

On the other hand, the Genie Z-22IC, with a working height of approximately 26 feet, is designed for less demanding applications. The Z-22IC is distinguished by its impressive zero-degree turning radius, allowing it to operate in confined spaces without sacrificing performance. It has a maximum platform capacity of 500 lbs, similar to the Z-34, but its smaller footprint enhances its maneuverability, making it particularly suited for indoor work and tight outdoor spaces.

Both models incorporate Genie’s signature technologies, such as the Genie Smart Link system, which provides real-time diagnostics and operational data, helping operators maintain efficiency and safety. The Z-34 and Z-22IC are equipped with advanced hydraulic systems that ensure stability during operation, reducing the likelihood of tipping or accidents.

In terms of power, the Genie Z-34 and Z-22IC can be equipped with either electric or dual-fuel options, providing flexibility based on the job site requirements. The electric models are ideal for indoor use due to their zero emissions, while dual-fuel versions can be deployed for outdoor tasks requiring more power.

Safety is paramount in the design of both aerial platforms. They include features such as automatic leveling, slip-resistant platforms, and emergency stop buttons to enhance worker safety during use. The inclusion of fascia guards and harness attachments ensure compliance with safety regulations and protect the operators.

Overall, the Genie Z-34 and Z-22IC combine advanced technology with practical design, making them indispensable tools in various fields requiring aerial access solutions. With their superior performance, safety features, and ease of use, these models stand out as top choices for professionals seeking efficient and reliable access equipment.