Genie Why Your Utility Vehicle Won't Drive or Start: Z-45/25 Troubleshooting Guide
Page 43

Fourth Edition · First Printing

Operator's Manual

 

 

 

 

Starting the Engine

1At the ground controls, turn the key switch to the desired position.

2Be sure both ground and platform control red Emergency Stop buttons are pulled out to the on position.

Gasoline/LPG models

3Choose fuel by moving the fuel select switch to the desired position.

4Move the engine start toggle switch to either side. If the engine fails to start or dies, the restart delay will disable the start switch for 3 seconds.

Diesel models

3Move the glow plug switch to either side and hold for 3 to 5 seconds.

4Move the engine start toggle switch to either side. If the engine fails to start or dies, the restart delay will disable the start switch for 3 seconds.

All models

If engine fails to start after 15 seconds of cranking, determine the cause and repair any malfunction. Wait 60 seconds before trying to start again.

In cold conditions, 20°F / -6°C and below, warm the engine for 5 minutes before operating to prevent hydraulic system damage.

Operating Instructions

In extreme cold conditions, 0°F / -18°C and below, machines should be equipped with optional cold start kits. Attempting to start the engine when temperatures are below 0°F / -18°C may require the use of a booster battery.

Gasoline/LPG models: In cold conditions, 20°F / -6°C and below, the machine should be started on gasoline and warmed for 2 minutes, then switched to LPG. Warm engines can be started on LPG.

Emergency Stop

Push in either ground or platform red Emergency Stop button to the off position to stop all functions and turn the engine off.

Repair any function that operates when the red Emergency Stop button is pushed in.

Selecting and operating the ground controls will override the platform red Emergency Stop button.

Auxiliary Controls

Use auxiliary power if the primary power source (engine) fails.

1Turn the key switch to ground or platform control.

2Pull out the red Emergency Stop button to the on position.

3Press down the foot switch when operating the auxiliary controls from the platform.

4Simultaneously hold auxiliary power switch on and activate the desired function.

The drive and steer functions will not operate with auxiliary power.

Part No.114339

Z-45/25 • Z-45/25J

41

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Operator’s Manual Contact us ContentsIntroduction Owners, Users and OperatorsDo Not Operate Unless Introduction Hazard Classification Safety Sign MaintenanceIntended Use Symbol and Hazard Pictorials Definitions Symbol and Hazard Pictorials Definitions General Safety 45/25 Z-45/25J Part No.114339 General Safety General Safety General Safety General Safety Personal Safety Fall Protection Maximum platform capacity Work Area Safety Electrocution HazardsTip-over Hazards Line Voltage Required ClearanceWork Area Safety Maximum allowable side force Ansi & CSA Maximum slope rating, stowed position, 2WD Work Area Safety Operation on Slopes HazardsMaximum slope rating, stowed position, 4WD Collision Hazards Work Area Safety Fall HazardsComponent Damage Hazards Work Area Safety Explosion and Fire HazardsBodily Injury Hazard Damaged Machine HazardsLockout After Each Use Work Area Safety Battery Safety Burn HazardsExplosion Hazard Electrocution HazardPage Platform Control Panel ControlsFourth Edition · First Printing Operators Manual Controls Controls Ground Control Panel Fourth Edition · First Printing Operators Manual Controls Inspections Pre-operation Inspection Fundamentals Inspections Pre-operation Inspection Inspections Function Test Fundamentals At the Ground Controls InspectionsTest Machine Functions Test the Foot SwitchAt the Platform Controls Test the HornTest Drive and Braking Test the Drive Enable SystemTest Limited Drive Speed Narrow Base Models Test Limited Drive Speed Standard Base ModelsTest the Lift/Drive Select Function if equipped Test the Oscillate Axle oscillating axle-equipped modelsTest Aircraft Protection Package if equipped Inspections Workplace Inspection FundamentalsDecal Description Quantity Inspections Inspection for Decals with WordsPart No.114339 45/25 Z-45/25J Inspections Inspection for Decals with Symbols Fourth Edition · First Printing Operators Manual Only use the machine as it was intended Operating Instructions Do Not Operate UnlessAuxiliary Controls Starting the EngineOperating Instructions Emergency StopTo Steer Operating Instructions Operation from GroundOperation from Platform To Position PlatformDriving on a slope Run RiseTo determine the slope grade Drive Speed Select Machine Not Level Indicator Light if equippedDrive Enable Generator if equippedAircraft Protection Package if equipped Operating Instructions Check Engine Light if equippedAfter Each Use Transport and Lifting Instructions Observe and Obey Free-wheel Configuration for WinchingSecuring the Chassis Securing to Truck or Trailer for TransitTransport and Lifting Instructions Securing the Platform Z-45/2545/25J Lifting InstructionsAxis Axis 45/25Ford DSG-423 EFI Engine EPA Compliant Maintenance Check the Engine Oil LevelMaintenance Symbols Legend Perkins 404C-22 EngineHydraulic oil specifications Maintenance Check the Hydraulic Oil LevelCheck the Engine Coolant Level Ford and Perkins Models Tire specifications 2WD Models 4WD Models Maintenance Check the BatteriesMaintenance Scheduled Maintenance Standard Base Models 45/25 no jib SpecificationsFloor loading information Standard Base Models 45/25J jib Maximum slope rating, stowed position Narrow Base Models 45/25 no jibNarrow Base Models 45/25J jib 45/25J Range of Motion 45/25 Range of Motion

Z-45, Z-25J, Z-45, Z-25 specifications

The Genie Z-45, Z-25, and Z-25J are pivotal equipment models in the realm of articulating boom lifts, renowned for their efficiency and versatility in various applications. Each model boasts a unique set of features, ensuring they cater to different operational needs across industries such as construction, maintenance, and industrial services.

The Genie Z-45, a robust articulating boom lift, stands out for its impressive working height of 51 feet and horizontal reach of 26 feet. It incorporates advanced hydraulic technology, allowing precise movements and smooth transitions when reaching elevated areas. The Z-45 is powered by a reliable 4WD drivetrain, enabling it to maneuver through rugged terrain with ease. It features a 180-degree rotating platform, enhancing its capability to position operators optimally for their tasks. The machine's compact design allows it to be easily transported and utilized in tight spaces, making it an excellent choice for congested job sites.

On the other hand, the Genie Z-25 shines in its compactness, achieving a maximum working height of 30 feet. With a horizontal reach of 20 feet, it is ideal for indoor environments and areas with limited access. It is equipped with a zero-degree turning radius, allowing for exceptional maneuverability. The Z-25's lightweight design and reliable electric and diesel engine options make it versatile for various applications. This model is particularly valued for its quiet operation and environmentally friendly features, making it an excellent fit for urban job sites where noise restrictions may apply.

Meanwhile, the Genie Z-25J is a noteworthy variant, combining the beneficial characteristics of the Z-25 with additional features suitable for tougher conditions. Like the Z-25, it offers great performance in confined spaces but with enhanced durability and functionality. It incorporates advanced technology, including an intuitive control system that simplifies operation even for novice users. The Z-25J is ideal for tasks requiring flexibility and reliability, such as maintenance work in elevated and hard-to-reach areas.

Each of these Genie models represents a commitment to innovation, durability, and efficiency, ensuring that operators are equipped with the best possible tools to tackle their projects safely and effectively. From the robust Z-45 to the compact Z-25 and the versatile Z-25J, Genie continues to lead the way in providing the ideal solutions for various lifting tasks.
Top Page Image Contents