Genie Z-45, Z-25J manual Fundamentals, Inspections Workplace Inspection

Page 37

Fourth Edition · First Printing

Operator's Manual

 

 

 

 

Do Not Operate Unless:

You learn and practice the principles of safe machine operation contained in this operator's manual.

1Avoid hazardous situations.

2Always perform a pre-operation inspection.

3Always perform function tests prior to use.

4Inspect the workplace.

Know and understand the workplace inspection before going on to the next section.

5 Only use the machine as it was intended.

Fundamentals

The workplace inspection helps the operator determine if the workplace is suitable for safe machine operation. It should be performed by the operator prior to moving the machine to the workplace.

It is the operator's responsibility to read and remember the workplace hazards, then watch for and avoid them while moving, setting up and operating the machine.

Inspections

Workplace Inspection

Be aware of and avoid the following hazardous situations:

·drop-offs or holes

·bumps, floor obstructions or debris

·sloped surfaces

·unstable or slippery surfaces

·overhead obstructions and high voltage conductors

·hazardous locations

·inadequate surface support to withstand all load forces imposed by the machine

·wind and weather conditions

·the presence of unauthorized personnel

·other possible unsafe conditions

Part No.114339

Z-45/25 • Z-45/25J

35

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Operator’s Manual Contact us ContentsIntroduction Owners, Users and OperatorsDo Not Operate Unless Introduction Hazard Classification Safety Sign MaintenanceIntended Use Symbol and Hazard Pictorials Definitions Symbol and Hazard Pictorials Definitions General Safety 45/25 Z-45/25J Part No.114339 General Safety General Safety General Safety General Safety Personal Safety Fall Protection Tip-over Hazards Work Area Safety Electrocution HazardsLine Voltage Required Clearance Maximum platform capacityWork Area Safety Maximum allowable side force Ansi & CSA Maximum slope rating, stowed position, 2WD Work Area Safety Operation on Slopes HazardsMaximum slope rating, stowed position, 4WD Collision Hazards Work Area Safety Fall HazardsBodily Injury Hazard Work Area Safety Explosion and Fire HazardsDamaged Machine Hazards Component Damage HazardsExplosion Hazard Work Area Safety Battery Safety Burn HazardsElectrocution Hazard Lockout After Each UsePage Platform Control Panel ControlsFourth Edition · First Printing Operators Manual Controls Controls Ground Control Panel Fourth Edition · First Printing Operators Manual Controls Inspections Pre-operation Inspection Fundamentals Inspections Pre-operation Inspection Inspections Function Test Fundamentals At the Ground Controls InspectionsAt the Platform Controls Test the Foot SwitchTest the Horn Test Machine FunctionsTest Drive and Braking Test the Drive Enable SystemTest Limited Drive Speed Narrow Base Models Test Limited Drive Speed Standard Base ModelsTest the Lift/Drive Select Function if equipped Test the Oscillate Axle oscillating axle-equipped modelsTest Aircraft Protection Package if equipped Inspections Workplace Inspection FundamentalsDecal Description Quantity Inspections Inspection for Decals with WordsPart No.114339 45/25 Z-45/25J Inspections Inspection for Decals with Symbols Fourth Edition · First Printing Operators Manual Only use the machine as it was intended Operating Instructions Do Not Operate UnlessOperating Instructions Starting the EngineEmergency Stop Auxiliary ControlsOperation from Platform Operating Instructions Operation from GroundTo Position Platform To SteerDriving on a slope Run RiseTo determine the slope grade Drive Enable Machine Not Level Indicator Light if equippedGenerator if equipped Drive Speed SelectAircraft Protection Package if equipped Operating Instructions Check Engine Light if equippedAfter Each Use Transport and Lifting Instructions Observe and Obey Free-wheel Configuration for WinchingTransport and Lifting Instructions Securing to Truck or Trailer for TransitSecuring the Platform Z-45/25 Securing the ChassisAxis Lifting InstructionsAxis 45/25 45/25JMaintenance Symbols Legend Maintenance Check the Engine Oil LevelPerkins 404C-22 Engine Ford DSG-423 EFI Engine EPA CompliantHydraulic oil specifications Maintenance Check the Hydraulic Oil LevelCheck the Engine Coolant Level Ford and Perkins Models Tire specifications 2WD Models 4WD Models Maintenance Check the BatteriesMaintenance Scheduled Maintenance Standard Base Models 45/25 no jib SpecificationsFloor loading information Standard Base Models 45/25J jib Maximum slope rating, stowed position Narrow Base Models 45/25 no jibNarrow Base Models 45/25J jib 45/25J Range of Motion 45/25 Range of Motion

Z-45, Z-25J, Z-45, Z-25 specifications

The Genie Z-45, Z-25, and Z-25J are pivotal equipment models in the realm of articulating boom lifts, renowned for their efficiency and versatility in various applications. Each model boasts a unique set of features, ensuring they cater to different operational needs across industries such as construction, maintenance, and industrial services.

The Genie Z-45, a robust articulating boom lift, stands out for its impressive working height of 51 feet and horizontal reach of 26 feet. It incorporates advanced hydraulic technology, allowing precise movements and smooth transitions when reaching elevated areas. The Z-45 is powered by a reliable 4WD drivetrain, enabling it to maneuver through rugged terrain with ease. It features a 180-degree rotating platform, enhancing its capability to position operators optimally for their tasks. The machine's compact design allows it to be easily transported and utilized in tight spaces, making it an excellent choice for congested job sites.

On the other hand, the Genie Z-25 shines in its compactness, achieving a maximum working height of 30 feet. With a horizontal reach of 20 feet, it is ideal for indoor environments and areas with limited access. It is equipped with a zero-degree turning radius, allowing for exceptional maneuverability. The Z-25's lightweight design and reliable electric and diesel engine options make it versatile for various applications. This model is particularly valued for its quiet operation and environmentally friendly features, making it an excellent fit for urban job sites where noise restrictions may apply.

Meanwhile, the Genie Z-25J is a noteworthy variant, combining the beneficial characteristics of the Z-25 with additional features suitable for tougher conditions. Like the Z-25, it offers great performance in confined spaces but with enhanced durability and functionality. It incorporates advanced technology, including an intuitive control system that simplifies operation even for novice users. The Z-25J is ideal for tasks requiring flexibility and reliability, such as maintenance work in elevated and hard-to-reach areas.

Each of these Genie models represents a commitment to innovation, durability, and efficiency, ensuring that operators are equipped with the best possible tools to tackle their projects safely and effectively. From the robust Z-45 to the compact Z-25 and the versatile Z-25J, Genie continues to lead the way in providing the ideal solutions for various lifting tasks.
Top Page Image Contents