Genie TMZ-17, TMZ-10, TMZ-50, TMZ-30 manual Check the Engine Oil Level, Engine Models

Page 17

First Edition • Third Printing

Operator's Manual

 

 

 

 

MAINTENANCE

Check the Engine Oil Level -

Check the Batteries

Engine Models

 

 

 

 

 

 

 

 

 

 

Maintaining the proper engine oil level is essential to good engine performance and service life. Operating the machine with an improper oil level can damage engine components.

Check the oil level with the engine off.

1 Check the oil level dipstick.

Result: The oil level should be at the FULL mark on the dipstick. Add oil as needed.

Honda GX340K1 Engine

Oil viscosity requirements

Temperature below 60°F / 15.5°C

5W-30

 

 

-10°F to 90° / -23°C to 32°C

10W-30

 

 

Temperature above -10°F / -23°C

10W-40 to 10W-50

 

 

Temperature above 20°F / -6.6°C

20W-40 or 20W-50

Use oils meeting API classification SG (labeled SG/CC or SG/CD) as they offer improved wear protection. Units ship with 10W-40 SG/CC

Hatz 1B30 Engine

Oil viscosity requirements

Temperature below 60°F / 15.5°C (synthetic)

5W-30

 

 

-10°F to 90° / -23°C to 32°C

10W-40

 

 

Temperature above -4°F / 34°C

15W-40

Engine oil should have properties of API classification CD, CE, CF or CG grades.

Units ship with 10W-40 SG/CC

Proper battery condition is essential to good engine performance and safe operation. Improper fluid levels or damaged cables and connections can result in engine component damage and hazardous conditions.

This procedure does not need to be performed on machines with sealed or maintenance-free batteries.

Bodily injury hazard. Batteries contain acid. Avoid spilling or contacting battery acid. Neutralize battery acid spills with baking soda and water.

1Put on protective clothing and eye wear.

2Be sure that the battery cable connections are tight and free of corrosion.

3Be sure that the battery hold-down straps are in place and secure.

4Remove the battery vent caps.

5Check the battery acid level. If needed, replenish with distilled water to the bottom of the battery fill tube. Do not overfill.

6Install the vent caps.

Part No. 72896

Genie TMZ-50/30 & Genie TMZ-17/10

15

Image 17
Contents Operator’s Manual Contact us ContentsDo Not Operate Unless Safety RulesTip-over Hazards Electrocution HazardsBodily Injury Hazard Component Damage Hazards Collision HazardsLifting Hazards Explosion and Fire HazardsTowing Hazards Damaged Machine HazardsMaterial Lifting Configuration Collision Hazards Personnel Lifting Configuration Tip-over HazardsFall Hazards Collision HazardDecal Legend Optional Drive System Tip over HazardsExplosion Hazards Battery Safety Burn HazardsTip-over Hazard Lifting HazardPlatform Control Panel ControlsGround Control Panel Drive Control Panel option Fundamentals Pre-operation InspectionPRE-OPERATION Inspection Pre-operation InspectionCheck the Hydraulic Oil Level Observe and Obey MaintenanceMaintenance Symbols Legend Engine Models Check the Engine Oil LevelCheck the Tires and Wheels Scheduled MaintenanceFunction Tests SetupFunction Tests Test Emergency Stop At the Ground ControlsTest Outrigger Interlock Test the Boom FunctionsTest the Horn At the Platform ControlsTest Machine Functions Test the Drive and Steering If equippedWorkplace Inspection Workplace InspectionOperating Instructions Set upEmergency Stop Only use the machine as it was intendedTowing Information TransportDC Models Manual Lowering Models with Engines Manual LoweringPrimary boom retract function All other functionsTo Position Platform Operation from GroundOperation from Platform Backing Up with Trailer If equipped with surge brake Optional Drive System Operating InstructionsTransport Not attached to a tow vehicle After Each UseMaterial Lifting Configuration Set up Material Lifting Configuration Observe and ObeyDry Battery Filling Charging Instructions Battery and Charger Instructions Observe and ObeyTo Charge Battery Voltage ConversionDecal Inspection DecalsDecals Specifications Genie Industries PO Box Redmond, WA Reporting Safety DefectsReporting Safety Defects Distributed By