Craftsman 270, 247 Jack Spindle Replacement, Drive Belt, Idler PulleyJ Flat Idler Transmissiol

Page 21

disengagingcompletelyForaproperworkingmachine,.

usebeltsavailablefromSears.

1.Follow Figure 25 for routing of belts and pulleys.

2.Periodically check to see if these belts are too loose

or damaged through wear and tear. If so, replace with new belt.

NOTE: It is recommended that both drive belts be replaced at the same time.

Special tools required: Vise grips or impact wrench.

_--Engine Pulley

Idler

PulleyJ

Flat Idler X(

" Transmissiol

Spin

Brak _/f

8.Replace with new belt making sure that the hardware is propedy secured and the belts are on the inside of the belt keepers.

Jack Spindle Replacement

Check jack spindle whenever you replace upper deck drive belts. If the jack spindle does not spin freely when the belts are disengaged, it should be replaced.

1.Disconnect and ground the spark plug wire.

2.Unhook both straps securing grass catcher to the vehicle frame. Remove grass catcher from unit and keep it aside.

3.Flip the utility bed up to access the jack spindle.

4.Loosen the jack spindle pulley bolt using a pair of wrenches. See Figure 26.

5.Remove the pulley from the jack spindle.

6.Remove four screws (only two called out in Figure

26)that secure jack spindle to the vehicle frame.

7.Remove the jack spindle.

_Pulley

Bolt

Jack Pulley

Spindle

Idlel

Figure 25

Upper Deck Drive Belt

I.Engage the parking brake and tum the ignition off.

2.Remove the cutting deck as instructed in the previous section.

3.Disconnect spindle brake bar at the idler pulley. Note the hardware positions for future use.

4.Remove the lower deck belt tension pulley arm. Do not remove the spring. Note hardware position.

5.Using a 9/16" socket, remove the bolt holding the engine pulley, and drop the pulley down. To loosen this bolt, you will have to hold the engine shaft firmly with vise grips at a point closest to the bottom of the vehicle frame. This will stop the shaft from rotating, and help in removing the engine pulley.

6.Roll the belt off the engine pulley.

7.Slip the belt off from the idler pulley. Remove the belt from the jack pulley.

Figure 26 ....

8.Replace with a new jack spindle and re-attach to the frame.

9.Working under the vehicle, re-install the jack spindle pulley with the bolt removed earlier.

10.Flip the utilitybed back to the operating position, re- attach grass catcher as needed, and re-connect the spark plug wire.

Drive Belt

IMPORTANT:When either or both of the drive belts are worn off, replace both. Replacing only one willaffect the performance of your lawn utility vehicle.

NOTE: It may be necessary to adjust the speed control linkage after replacing both drive belts.

1.Remove the cutting deck.

21

Image 21
Contents 2002 Form noContent ContentGeneral Operation AdjustmentsSlope Operation ChildrenSafe Handling Of Gasoline Oil or fuel spillage and remove any fuel soaked debris Your ResponsibilityLa= Attaching Mulch Plug Unpacking UnitLoose Parts Attaching Side-Discharge ChuteGrass Catcher Chute Attaching Grass CatcherFlat Washer Deck Mulch Plug Deck -Lift LeverKnow Your Lawn Utility Vehicle Deck Lift LeverDrive Pedal Parking Brake Blade Control LeverBrake Pedal Starting the Engine Before StartingFilling Up Oil Type of OilStopping the Vehicle Using as MowerEmergency Stopping Operating the VehicleUsing as Utility Cart Using as MulcherRemoving Deck Maintenance ScheduleGeneral Recommendation Cutting BladeChanging Air Cleaner ReassemblyMaintaining Engine SharpeningLubrication BrakeSpark Plug Completely loosen the two screws that holdBattery Cleaning the EquipmentTires Deck Engagement Adjusting Seat PositionDeck Levelling CiipWheel Alignment Adjusting Speed Control RodAdjusting Shift Linkage Adjusting BrakeReplacing Fuse Changing BeltDrive Belt Jack Spindle ReplacementIdler PulleyJ Flat Idler Transmissiol Bolt Jack PulleyBelt KeeperStoring the Equipment Preparing for StorageAfter Storage EngineTrouble PossibleCause Enginefailstostart Parts List for Craftsman Lawn Utility Vehicle Model OnlyChoke mounts to seat plate 49 ,-0826 Disengage safely. a substitute non 710-0902 For painted 710-0604A Key No. Part NoOnly For referenceSpindle Shaft Shoulder Spacer Craftsman Lawn Utility Vehicle Model Key No. Part No Seat Switch Shock 5o5@ 445 188 190 613A 3As ?305 930A 332455@ 1005 305 Description495265 Dipstick Tube 832 691466 Muffler Guard Garanta Limitada Sobre EL Vehculo Utilitario Cortacisped Advertencia Funcionamiento generalPequeos Operaci6n en pendientesServicio Su responsabilidadManejo seguro de la gasoline Pendientes DE lSoPiezas sueltas Desempaque la UnidadTolva De Descarga Lateral Adaptador Para ForrajeTolva del recolector de pasto Recolector de pastoRetiro del recolector de pasto Illo de manoPedal de avance Palanca para levantar la cubiertaDe aceite/varilla del aceite SeccinFreno de mano Palanca de cambiosPoavasos Palanca de control de cuchillasArranque del motor Antes de iniciarDetener el vehiculo Operaci6n del vehfculoEl parar de la emergencia Uso del cortacdspedUso como carro de servicio Uso del cortacdsped para armado de forrajePara vaciar el recolector de pasto PJataf.omadePrograma de mantenimiento Recomendaciones generalesRetiro de la cubierta CuchillaCambio de aceite del motor Mantenimiento del motorAfilado ReensamblajeFreno LubricacidnEspecificaciones para afinaci6n Ajuste la bujfa de encendidoNeumdticos Limpieza del equipoAcumulador eldctrico Conexi6n de cables de la bateriaPosicibn del asiento AjustesNivelaci6n de la cubierta Enganche de la cubiertaAlineacibn de las ruedas Barra de control de velocidadEnlace de cambios Reemplazo del fusibleCambio de correa Correa de propulsi6n superior de a cubierta Reemplazo del vdstago de conexi6nPolea de velocidad variable Polea Ioca Reemplace con un nuevo vdstagode conexi6n yCorrea propulsora Prepardndose para el alrnacenajeAcumulador el6ctrico MotorSalvando el equipo Despuds del almacenajeEquipo Canada Part

270, 250, 247 specifications

The Craftsman 247,250,270 series of outdoor power equipment represents a robust lineup designed for both home gardening enthusiasts and professionals. These versatile machines offer a blend of durability, efficiency, and ease of use, making them invaluable for tackling various landscaping tasks.

One of the standout features of the Craftsman 247 series is its reliable engine performance. Powered by a strong, efficient engine, these machines deliver consistent power, whether you are mowing, trimming, or performing other gardening tasks. The engines are engineered for easier starting and smoother operation, reducing the frustration often associated with outdoor equipment.

The cutting technology employed in the 247 series deserves special mention. Many models come equipped with a precise cutting deck that boasts multiple height adjustments, allowing users to tailor the cutting height to suit different grass types and mowing conditions. This flexibility ensures a clean cut every time, promoting healthier lawn growth.

In terms of user comfort, the Craftsman 247,250,270 models incorporate ergonomic designs. The controls are intuitively placed, allowing for easy access while mowing. Additionally, features like adjustable handles and padded grips enhance overall user comfort, reducing fatigue during extended use.

Another notable characteristic of this series is its focus on durability. The materials used in the construction are selected for their resilience, ensuring that these machines can withstand the rigors of regular use. Steel decks and heavy-duty frames not only increase the longevity of the equipment but also provide stability during operation.

The Craftsman 247 series also incorporates modern technology to enhance usability. Some models feature electric start options, eliminating the hassle of manual pull-starts. Furthermore, the addition of innovative safety features such as automatic shut-off systems ensures that both the user and the machine remain safe during operation.

For those looking to tackle varied terrains, the 247 series offers machines with versatile wheel designs and traction capabilities. This allows for effective operation on both flat and uneven ground, making these models suitable for a variety of landscaping challenges.

In conclusion, the Craftsman 247,250,270 series is a robust solution tailored to meet the needs of gardeners and landscapers alike. With their powerful engines, user-friendly designs, and durable construction, these machines stand out as reliable workhorses in the outdoor power equipment market. Whether you are maintaining a pristine lawn or handling more extensive landscaping projects, these Craftsman models are equipped to deliver performance and efficiency.