Bryant ASPAX1BBA015 Specifications, Fuel Requirements Recommendations, Fuel Consumption

Page 8

Section 1 — General Information

15 kW Generator

1.6SPECIFICATIONS

‹1.6.1 GENERATOR

Rated Max. Cont. Power Capacity (Watts*)

..... 13,000 NG/

 

 

15,000 LP†

Rated Voltage

120/240

Rated Max. Continuous Load Current (Amps)

120 Volts +

108.3 NG/125.0 LP

240 Volts

54.2 NG/62.5 LP

Main Line Circuit Breaker

65 Amp

Phase

1

Number of Rotor Poles

2

Rated AC Frequency

60 Hz

Power Factor

1

Recommended Air Filter

Part # 0C8127

Battery Requirement at

 

 

-17.8° C (0° F)

Group 26/26R 12 Volts and

525 Cold-cranking Amperes Minimum

Weight

487 Pounds

Output Sound Level @ 23 ft (7m)

 

at full load

71.5 db (A)

Normal Operating Range

-20°F (-28.8°C)

 

 

to 104°F (40°C)

*Maximum wattage and current are subject to and limited by such factors as fuel Btu content, ambient temperature, altitude, engine power and con- dition, etc. Maximum power decreases about 3.5 percent for each 1,000 feet above sea level; and also will decrease about 1 percent for each 6° C (10° F) above 16° C (60° F).

+Total current in two separate circuits. Current in each circuit must not exceed the value stated for 240V.

1.7FUEL REQUIREMENTS

AND RECOMMENDATIONS

With LP gas, use only the vapor withdrawal sys- tem. This type of system uses the vapors formed above the liquid fuel in the storage tank.

The engine has been fitted with a fuel carburetion system that meets the specifications of the 1997 California Air Resources Board for tamper-proof dual fuel systems. The unit will run on natural gas or LP gas, but it has been factory set to run on natural gas. Should the primary fuel need to be changed to LP gas, the fuel system needs to be reconfigured. See instructions in the “Reconfiguring the Fuel System” section.

Recommended fuels should have a Btu content of at least 1,000 Btus per cubic foot for natural gas; or at least 2,520 Btus per cubic foot for LP gas. Ask the fuel supplier for the Btu content of the fuel.

Required fuel pressure for natural gas is 5 inches to 7 inches water column (0.18 to 0.25 psi); and for liquid propane, 11 inches to 14 inches of water column (0.4 to 0.5 psi).

NOTE:

Any piping used to connect the generator to the fuel supply should be of adequate size to ensure the fuel pressure NEVER drops below 4 inches water column for natural gas or 10 inches water column for liquid propane for all load ranges.

‹ 1.6.2 ENGINE

Type of Engine

GT-990

Number of Cylinders

2

Rated Horsepower

30 @ 3,600 rpm

Displacement

992cc

Cylinder Block

Aluminum w/Cast Iron Sleeve

Valve Arrangement

Overhead Valves

Ignition System

Solid-state w/Magneto

Recommended Spark Plug

RC12YC

Spark Plug Gap

0.508 mm (0.020 inch)

Compression Ratio

9.5:1

Starter

12Vdc

Oil Capacity Including Filter

Approx. 1.7 Qts

Recommended Oil Filter

Part # 070185

Recommended Air Filter

Part # 0C8127

Operating RPM

3,600

1.8FUEL CONSUMPTION

 

Model #

Nat. Gas (*)

LP Vapor (**)

 

 

 

1/2 Load

Full Load

1/2 Load

Full Load

 

 

05207

156

220

1.58/58

2.40/88

 

 

 

 

 

 

 

 

*Natural gas is in cubic feet per hour.

**LP is in gallons per hour/cubic feet per hour.

***Values given are approximate.

DANGER

Gaseous fuels such as natural gas and liquid propane (LP) gas are highly explosive. Even the slightest spark can ignite such fuels and cause an explosion. No leakage of fuel is permitted. Natural gas, which is lighter than air, tends to collect in high areas. LP gas is heavier than air and tends to settle in low areas.

6

Image 8
Contents Installation ‹ Contents ‹ Operation and Maintenance‹ HOW to Obtain Service IntroductionPost Installation Start-up Adjustments MaintenanceTroubleshooting Introduction Inside Front Cover Warning   Explosion Hazards  ‹ Standards IndexUNPACKING/INSPECTION LocationProtection Systems System SET LEDGenerator GfciSpecifications Fuel Requirements RecommendationsFuel Consumption ‹ 1.6.1 Generator‹ 1.10.1 Generator Fuel System‹ 1.9.1 15KW, 990CC Engines Battery Installation Battery‹ 1.10.2 Transfer Switch 10.2.1 15 kW UnitsElectrical Checks Check Transfer Switch OperationBefore Initial START-UP Generator Tests Under Load Checking Automatic OperationAdjusting the Regulator Natural GAS only Dual Fuel Regulators‹ 2.7.1 15 KW Units Voltage Regulator AdjustmentBREAK-IN Procedure ‹ 3.3.1 12 VDC Accessory Outlet Automatic Transfer Operation‹ 3.2.1 Auto Position ‹ 3.2.2 OFF Position‹ 3.5.1 Transfer to Generator Power Source Sequence of Automatic OperationManual Transfer Operation ‹ 3.3.2 120 VAC Gfci OutletSetting the Exercise Timer ‹ 3.5.2 Transfer Back to Utility Power Source‹ 3.7.1 LOW OIL Pressure Switch ‹ 3.7.2 High Temperature SwitchChanging the Engine OIL Checking the Engine OIL LevelFuses ‹ 4.3.2 OIL Change Procedure Changing the OIL FilterSpark Plugs ‹ 4.5.1 15 KW GeneratorsBattery Maintenance Adjusting Valve ClearanceCooling System Corrosion Protection‹ 4.12.2 Return to Service OUT of Service Procedure‹ 4.12.1 Removal from Service Service Schedule Be performed by the nearest dealerTroubleshooting Guide Problem Cause CorrectionMounting Dimensions Electrical Data Customer Connection KW Generator Electrical Schematic Drawing No E9017 SW1 Exploded Views and Parts Lists Part NO. QTY. Description KW Generator Control Panel Drawing No E9162-J Part NO. QTY Description 16B Item Part NO. QTY. Description 138 122 KNOB, AIR Cleaner Views and Parts Lists QTY Description KW Generator Gas Regulator Drawing No D8720-G CASTING, Twin Regulator Housing California and Federal Emission Control Warranty Statement Emission Control System Warranty Warranty Schedule