Murray 1695722, 1737920 manual Operation, Before Operating Snow Thrower

Page 12

OPERATION

BEFORE OPERATING SNOW THROWER

■Check the fasteners. Make sure all fasteners are tight.

■On electric start models, the unit was shipped with the starter cord plugged into the engine. Before operating, unplug the starter cord from the engine.

NOTE: This snow thrower was shipped WITH OIL in the engine. See “Before Starting Engine” instructions in the OPERATION section of this manual before starting engine.

CHECK THE TIRES

Check tires for damage. Check the air pressure in the tires with an accurate gauge (see Figure 4).

CAUTION: Avoid Injury! Explosive separation of tire and rim parts is possible when they are serviced incorrectly.

•Do not attempt to mount a tire without the proper equipment and experience to perform the job.

•Do not inflate the tires above the recommended pressure.

•Do not weld or heat a wheel and tire assembly. Heat can cause an increase in air pressure resulting in an explosion. Welding can structurally weaken or deform the wheel.

•Do not stand in front or over the tire assembly when inflating. Use appropriate tool that allows you to stand to one side.

NOTICE: Check side of tire for maximum tire pressure. DO NOT exceed maximum.

Checking Tire Air Pressure

Figure 4

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operator’s Manual Manual Part NoWhere to Find Us Date PurchasedTable of Contents Operator Safety Slow Engine Run Fast Engine StopTraction Control Engage DownOperation and Equipment Safety Moving Parts Maintenance and Storage Shift Decal Auger Control Decal Main Dash DecalFeatures and Controls Engine and Snow Thrower ControlsFeatures and Controls Snow Thrower ControlsOperation Before Operating Snow ThrowerOperate the Snow Thrower Stop the Snow ThrowerControl Levers Traction Lock Pins Traction Lock PinsCheck the OIL Before Starting Engine Checking the OilFill the Fuel Tank Start the EngineStarting Engine Stop the Engine Stopping EngineClear a Clogged Discharge Chute Operating TipsMaintenance Cable AdjustmentAfter Each USE Adjust the Drag on the Chute Rotation Lubricate Auger Gear BOXLubricate Auger Shaft Fittings CHECK/LUBRICATE FREE-HAND LinkageEngine Maintenance Oil Drain PlugChange the Spark Plug Remove the Snow HoodAdjust Skid Height Adjusting Skid HeightBelt Adjustment SecondsCheck Tension on Auger Drive Belt Belt Guide Adjustment Check and Adjust the CablesAdjusting Belt Drive Adjusting Auger Drive CableTraction Drive Cable Auger Shear PIN Replacement Storage OFF Season StorageRemove from Storage Troubleshooting Problem Look for RemedyLimited Warranty WarrantiesBriggs & Stratton Emissions Control Warranty Provisions Specifications Page Manuel d’Utilisation Réf. fab DescriptionSouffleuse à neige MoteurDate d’achat Où nous trouverTable DES Matières Protection des oreilles Surface chauderecommandée pour une Ou modéréesRotatifs Manette de tarière Marche avant Point mort Marche arrièreSécurité de l’utilisation et de l’équipement Dange Sécurité du moteur suite Étiquettes du moteur Réf Réf Auger Étiquette Étiquette Tableau de bord principalÉtiquettes de sécurité Commandes DU Moteur ET DE LA Souffleuse À Neige Commandes de moteurPoignée de lanceur Sert à démarrer le moteur à la main Fontions ET Commandes Commandes de la soufleuse à neigeNe pas gonfler les pneus-dessus de la pression recommandée Avant D’UTILISATION Souffleuse À NeigeContrôler LES Pneus Vérifier la pression dair des pneusUtilisation DE LA Souffleuse À Neige Arrêter LA Souffleuse À NeigeNeige mouillée, lourde, fondante, très profonde Transport uniquementTraction goupille de sûreté Et au-dessusEt en dessous Contrôler le niveau d’huileRemplir LE Réservoir D’ESSENCE Démarrer LE MoteurArrêter LE Moteur Conseils D’UTILISATION Toujours utiliser un outil de nettoyage, pas les mainsOutil de nettoyage Autant que possible, projeter la neige dans le sens du ventAprès Chaque Utilisation Graissage DE L’ARBRE DE VIS Sans FIN Contrôles de graissageGraissage de la boîte d’engrenage de vis sans fin Pignon de rotation de goulotteVoir les huiles recommandées dans le tableau ci-contre Entretien DU MoteurEt au-dessus E W30 Et en dessous Synthétique 5W30 Bouchon de vidange d’huileLa bougie E est à présent accessible Changer LA Bougie D’ALLUMAGEDéposer le capot à neige FixationRégler ou changer la bougie Régler LA Hauteur DES PatinsLes patins se règlent de la manière suivante Régler la hauteur des patinsAjustement DES Courroies Courroie d’entraînement de tractionCourroie d’entraînement de vis sans fin Ajustement DU Guide DE Courroie Contrôle ET Réglage DES CâblesCâble d’entraînement de vis sans fin Réglage guide de courroieCâble de commande de traction Changer LES Goupilles DE Cisaillement DE VIS Sans FIN Remisage Hors Saison Sortir LA Souffleuse À Neige DU RemisageLubrifier arbre hexagonal et chaînes Démarrage difficile Le moteur a des ratésMoteur est chaud Le moteur caleGaranties Novembre Informations concernant la puissance théorique du moteur Bougie en platine longue durée Dispositif d’allumageDéflecteur de goulotte Manuel Rotation de la goulotte Type d’entraînement

1737920, 1695722 specifications

Murray 1737920 and 1695722 represent two significant advancements in the realm of smart technology, particularly in the area of home automation and energy management. These devices integrate cutting-edge features designed to enhance user experience while optimizing energy efficiency.

One of the main characteristics of Murray 1737920 is its intelligent energy management system, which utilizes real-time data analytics to monitor energy consumption patterns. The device employs machine learning algorithms to intelligently predict energy requirements, allowing users to reduce waste and lower their utility bills. Additionally, it has a user-friendly interface that provides insights into energy usage, enabling homeowners to make informed decisions about their consumption.

Murray 1695722, on the other hand, focuses more on home automation and security. With built-in Wi-Fi connectivity, it allows users to control various appliances remotely through a dedicated mobile application. This feature not only enhances convenience but also allows for enhanced security by enabling users to monitor their homes in real-time. The device is equipped with motion sensors and alert systems that can notify homeowners of any unusual activity, adding an extra layer of protection.

Both devices integrate seamlessly with existing smart home ecosystems, supporting popular communication protocols such as Zigbee and Z-Wave. This compatibility allows users to expand their systems by adding other smart devices, creating a fully integrated home automation experience.

In terms of installation, both Murray models are designed to be user-friendly. They typically come with comprehensive instructions, and many features can be accessed with minimal technical knowledge. The focus on ease of use extends to their maintenance, with straightforward troubleshooting and support available through the manufacturers.

Another important feature of both devices is their commitment to sustainability. By helping families monitor and manage their energy consumption, they play a crucial role in promoting more eco-friendly practices within households. Combined, Murray 1737920 and 1695722 stand out as leaders in smart home technology, emphasizing efficiency, security, and user-centric design principles that cater to the evolving needs of modern homeowners. These innovations represent a significant step forward in creating energy-conscious and secure living environments.
Top Page Image Contents