Murray 1737920, 1695722 manual Belt Adjustment, Seconds, Check Tension on Auger Drive Belt

Page 23

 

 

 

MAINTENANCE

BELT ADJUSTMENT

 

 

Traction Drive Belt

 

 

The traction drive belt has constant spring pressure and does not require

 

 

an adjustment. If the traction drive belt is slipping, replace the belt. See au-

 

 

thorized dealer.

 

 

Auger Drive Belt

 

 

If your snow thrower will not discharge snow, check the control cable adjust-

 

 

ment. If it is correct, then check the condition of the auger drive belt. If it is

 

 

damaged or loose, replace it (see authorized dealer).

 

 

1.

Disconnect spark plug wire.

 

 

2.

Remove screw (A, Figure 24) from belt cover (B). Remove belt cover.

 

 

3.

Loosen nut on idler drive pulley (A, Figure 25) and move idler drive

 

B

 

pulley towards belt about 1/8 inch (3 mm).

 

 

WARNING: Do not over-tighten, as this may lift the

 

A

 

lever and cause the auger drive to be engaged without

 

 

depressing the auger control.

 

 

4.

Tighten nut.

Adjusting Auger Drive Belt

Figure 24

 

 

5.

With the aid of an assistant, engage the auger drive clutch. Check ten-

 

 

 

sion on belt which is opposite idler pulley (B, Figure 25). Belt should

 

 

 

deflect about 1/2 inch (12.5 mm) with moderate pressure. You may

 

 

 

have to move idler pulley more than once to obtain the correct ten-

 

3

 

sion.

A

8

 

(125mm)

6.

Release the auger drive control lever. The auger must stop within five

 

.

 

1/2”

 

(5) seconds.

 

Deflection

 

 

 

7.

If auger does not operate properly, stop engine and recheck drive

B

 

 

linkage adjustments.

 

 

8.Reinstall belt cover (B, Figure 24). Tighten screw (A).

9.Whenever belts are adjusted or replaced, the cables will need to be adjusted (see “Check and Adjust the Cables” section).

10.Attach the spark plug wire.

Check Tension on Auger Drive Belt

Figure 25

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Manual Part No Operator’s ManualDate Purchased Where to Find UsTable of Contents Operator Safety Engage Down Slow Engine Run FastEngine Stop Traction ControlOperation and Equipment Safety Moving Parts Maintenance and Storage Auger Control Decal Main Dash Decal Shift DecalEngine and Snow Thrower Controls Features and ControlsSnow Thrower Controls Features and ControlsBefore Operating Snow Thrower OperationControl Levers Operate the Snow ThrowerStop the Snow Thrower Checking the Oil Traction Lock PinsTraction Lock Pins Check the OIL Before Starting EngineStarting Engine Fill the Fuel TankStart the Engine Stopping Engine Stop the EngineOperating Tips Clear a Clogged Discharge ChuteAfter Each USE MaintenanceCable Adjustment CHECK/LUBRICATE FREE-HAND Linkage Adjust the Drag on the Chute RotationLubricate Auger Gear BOX Lubricate Auger Shaft FittingsOil Drain Plug Engine MaintenanceRemove the Snow Hood Change the Spark PlugAdjusting Skid Height Adjust Skid HeightCheck Tension on Auger Drive Belt Belt AdjustmentSeconds Adjusting Auger Drive Cable Belt Guide AdjustmentCheck and Adjust the Cables Adjusting Belt DriveTraction Drive Cable Auger Shear PIN Replacement Remove from Storage StorageOFF Season Storage Problem Look for Remedy TroubleshootingWarranties Limited WarrantyBriggs & Stratton Emissions Control Warranty Provisions Specifications Page Réf. fab Description Manuel d’UtilisationOù nous trouver Souffleuse à neigeMoteur Date d’achatTable DES Matières Rotatifs Protection des oreilles Surface chauderecommandée pour uneOu modérées Marche avant Point mort Marche arrière Manette de tarièreSécurité de l’utilisation et de l’équipement Dange Sécurité du moteur suite Étiquettes de sécurité Étiquettes du moteur RéfRéf Auger Étiquette Étiquette Tableau de bord principal Poignée de lanceur Sert à démarrer le moteur à la main Commandes DU Moteur ET DE LA Souffleuse À NeigeCommandes de moteur Commandes de la soufleuse à neige Fontions ET CommandesVérifier la pression dair des pneus Ne pas gonfler les pneus-dessus de la pression recommandéeAvant D’UTILISATION Souffleuse À Neige Contrôler LES PneusTransport uniquement Utilisation DE LA Souffleuse À NeigeArrêter LA Souffleuse À Neige Neige mouillée, lourde, fondante, très profondeContrôler le niveau d’huile Traction goupille de sûretéEt au-dessus Et en dessousDémarrer LE Moteur Remplir LE Réservoir D’ESSENCEArrêter LE Moteur Autant que possible, projeter la neige dans le sens du vent Conseils D’UTILISATIONToujours utiliser un outil de nettoyage, pas les mains Outil de nettoyageAprès Chaque Utilisation Pignon de rotation de goulotte Graissage DE L’ARBRE DE VIS Sans FINContrôles de graissage Graissage de la boîte d’engrenage de vis sans finBouchon de vidange d’huile Voir les huiles recommandées dans le tableau ci-contreEntretien DU Moteur Et au-dessus E W30 Et en dessous Synthétique 5W30Fixation La bougie E est à présent accessibleChanger LA Bougie D’ALLUMAGE Déposer le capot à neigeRégler la hauteur des patins Régler ou changer la bougieRégler LA Hauteur DES Patins Les patins se règlent de la manière suivanteCourroie d’entraînement de vis sans fin Ajustement DES CourroiesCourroie d’entraînement de traction Réglage guide de courroie Ajustement DU Guide DE CourroieContrôle ET Réglage DES Câbles Câble d’entraînement de vis sans finCâble de commande de traction Changer LES Goupilles DE Cisaillement DE VIS Sans FIN Lubrifier arbre hexagonal et chaînes Remisage Hors SaisonSortir LA Souffleuse À Neige DU Remisage Le moteur cale Démarrage difficileLe moteur a des ratés Moteur est chaudGaranties Novembre Type d’entraînement Informations concernant la puissance théorique du moteurBougie en platine longue durée Dispositif d’allumage Déflecteur de goulotte Manuel Rotation de la goulotte

1737920, 1695722 specifications

Murray 1737920 and 1695722 represent two significant advancements in the realm of smart technology, particularly in the area of home automation and energy management. These devices integrate cutting-edge features designed to enhance user experience while optimizing energy efficiency.

One of the main characteristics of Murray 1737920 is its intelligent energy management system, which utilizes real-time data analytics to monitor energy consumption patterns. The device employs machine learning algorithms to intelligently predict energy requirements, allowing users to reduce waste and lower their utility bills. Additionally, it has a user-friendly interface that provides insights into energy usage, enabling homeowners to make informed decisions about their consumption.

Murray 1695722, on the other hand, focuses more on home automation and security. With built-in Wi-Fi connectivity, it allows users to control various appliances remotely through a dedicated mobile application. This feature not only enhances convenience but also allows for enhanced security by enabling users to monitor their homes in real-time. The device is equipped with motion sensors and alert systems that can notify homeowners of any unusual activity, adding an extra layer of protection.

Both devices integrate seamlessly with existing smart home ecosystems, supporting popular communication protocols such as Zigbee and Z-Wave. This compatibility allows users to expand their systems by adding other smart devices, creating a fully integrated home automation experience.

In terms of installation, both Murray models are designed to be user-friendly. They typically come with comprehensive instructions, and many features can be accessed with minimal technical knowledge. The focus on ease of use extends to their maintenance, with straightforward troubleshooting and support available through the manufacturers.

Another important feature of both devices is their commitment to sustainability. By helping families monitor and manage their energy consumption, they play a crucial role in promoting more eco-friendly practices within households. Combined, Murray 1737920 and 1695722 stand out as leaders in smart home technology, emphasizing efficiency, security, and user-centric design principles that cater to the evolving needs of modern homeowners. These innovations represent a significant step forward in creating energy-conscious and secure living environments.
Top Page Image Contents