Murray 1695722, 1737920 Belt Guide Adjustment, Check and Adjust the Cables, Adjusting Belt Drive

Page 24

MAINTENANCE

BELT GUIDE ADJUSTMENT

1.Remove spark plug wire.

2.Have someone engage the auger drive. This will engage auger idler pulley (A, Figure 26).

3.Measure the distance between the belt guide (B) and belt (C). The distance should be about 1/8 inch (3 mm).

4.If adjustment is necessary, loosen belt guide mounting bolt. Move belt guide to the correct position. Tighten mounting bolt.

5.Install belt cover.

6.Connect spark plug wire.

B

1/8” (3mm)

A

C

Screw

Adjusting Belt Drive

Figure 26

CHECK AND ADJUST THE CABLES

The cables are adjusted at the factory and no adjustment should be necessary. If the cables have become stretched or are sagging adjustment will be necessary.

Whenever belts are adjusted or replaced, the cables will need to be ad- justed.

Auger Drive Cable

WARNING: Do not over-tighten, as this may lift the lever and cause the auger drive to be engaged without depressing the auger drive control.

1.With the auger drive control lever released, the hook (A, Figure 27) should barely touch the lever (B) without raising it. There can be a maximum of 1/32" (0.8 mm) clearance.

2.To adjust, loosen the nut (C) by holding the adjusting flats (D) and turning the nut. Then, turn the adjusting flats and hold the adjust- ment screw (E). The adjustment screw is a phillips screw and the head can be held or turned by inserting a screwdriver through the spring (F).

3.Hold the adjusting flats and tighten the nut.

4.Start the engine and check the auger. The auger must not be engaged unless the auger drive control lever is depressed.

5.With the engine running, fully depress the auger drive control lever. The auger should engage and run normally.

6.Release the auger drive control lever. The auger must stop within five

(5) seconds.

 

D

 

C

E

F

 

A

 

B

1/32”

(0.8mm)

 

Adjusting Auger Drive Cable

Figure 27

7.If the auger does not operate properly, stop the engine and recheck the auger drive cable adjustment.

8.If the drive linkage is properly adjusted, the tension of the auger drive belt may require an adjustment (see “Belt Adjustment” section).

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Operator’s Manual Manual Part NoWhere to Find Us Date PurchasedTable of Contents Operator Safety Slow Engine Run Fast Engine StopTraction Control Engage DownOperation and Equipment Safety Moving Parts Maintenance and Storage Shift Decal Auger Control Decal Main Dash DecalFeatures and Controls Engine and Snow Thrower ControlsFeatures and Controls Snow Thrower ControlsOperation Before Operating Snow ThrowerOperate the Snow Thrower Stop the Snow ThrowerControl Levers Traction Lock Pins Traction Lock PinsCheck the OIL Before Starting Engine Checking the OilFill the Fuel Tank Start the EngineStarting Engine Stop the Engine Stopping EngineClear a Clogged Discharge Chute Operating TipsMaintenance Cable AdjustmentAfter Each USE Adjust the Drag on the Chute Rotation Lubricate Auger Gear BOXLubricate Auger Shaft Fittings CHECK/LUBRICATE FREE-HAND LinkageEngine Maintenance Oil Drain PlugChange the Spark Plug Remove the Snow HoodAdjust Skid Height Adjusting Skid HeightBelt Adjustment SecondsCheck Tension on Auger Drive Belt Belt Guide Adjustment Check and Adjust the CablesAdjusting Belt Drive Adjusting Auger Drive CableTraction Drive Cable Auger Shear PIN Replacement Storage OFF Season StorageRemove from Storage Troubleshooting Problem Look for RemedyLimited Warranty WarrantiesBriggs & Stratton Emissions Control Warranty Provisions Specifications Page Manuel d’Utilisation Réf. fab DescriptionSouffleuse à neige MoteurDate d’achat Où nous trouverTable DES Matières Protection des oreilles Surface chauderecommandée pour une Ou modéréesRotatifs Manette de tarière Marche avant Point mort Marche arrièreSécurité de l’utilisation et de l’équipement Dange Sécurité du moteur suite Étiquettes du moteur Réf Réf Auger Étiquette Étiquette Tableau de bord principalÉtiquettes de sécurité Commandes DU Moteur ET DE LA Souffleuse À Neige Commandes de moteurPoignée de lanceur Sert à démarrer le moteur à la main Fontions ET Commandes Commandes de la soufleuse à neigeNe pas gonfler les pneus-dessus de la pression recommandée Avant D’UTILISATION Souffleuse À NeigeContrôler LES Pneus Vérifier la pression dair des pneusUtilisation DE LA Souffleuse À Neige Arrêter LA Souffleuse À NeigeNeige mouillée, lourde, fondante, très profonde Transport uniquementTraction goupille de sûreté Et au-dessusEt en dessous Contrôler le niveau d’huileRemplir LE Réservoir D’ESSENCE Démarrer LE MoteurArrêter LE Moteur Conseils D’UTILISATION Toujours utiliser un outil de nettoyage, pas les mainsOutil de nettoyage Autant que possible, projeter la neige dans le sens du ventAprès Chaque Utilisation Graissage DE L’ARBRE DE VIS Sans FIN Contrôles de graissageGraissage de la boîte d’engrenage de vis sans fin Pignon de rotation de goulotteVoir les huiles recommandées dans le tableau ci-contre Entretien DU MoteurEt au-dessus E W30 Et en dessous Synthétique 5W30 Bouchon de vidange d’huileLa bougie E est à présent accessible Changer LA Bougie D’ALLUMAGEDéposer le capot à neige FixationRégler ou changer la bougie Régler LA Hauteur DES PatinsLes patins se règlent de la manière suivante Régler la hauteur des patinsAjustement DES Courroies Courroie d’entraînement de tractionCourroie d’entraînement de vis sans fin Ajustement DU Guide DE Courroie Contrôle ET Réglage DES CâblesCâble d’entraînement de vis sans fin Réglage guide de courroieCâble de commande de traction Changer LES Goupilles DE Cisaillement DE VIS Sans FIN Remisage Hors Saison Sortir LA Souffleuse À Neige DU RemisageLubrifier arbre hexagonal et chaînes Démarrage difficile Le moteur a des ratésMoteur est chaud Le moteur caleGaranties Novembre Informations concernant la puissance théorique du moteur Bougie en platine longue durée Dispositif d’allumageDéflecteur de goulotte Manuel Rotation de la goulotte Type d’entraînement

1737920, 1695722 specifications

Murray 1737920 and 1695722 represent two significant advancements in the realm of smart technology, particularly in the area of home automation and energy management. These devices integrate cutting-edge features designed to enhance user experience while optimizing energy efficiency.

One of the main characteristics of Murray 1737920 is its intelligent energy management system, which utilizes real-time data analytics to monitor energy consumption patterns. The device employs machine learning algorithms to intelligently predict energy requirements, allowing users to reduce waste and lower their utility bills. Additionally, it has a user-friendly interface that provides insights into energy usage, enabling homeowners to make informed decisions about their consumption.

Murray 1695722, on the other hand, focuses more on home automation and security. With built-in Wi-Fi connectivity, it allows users to control various appliances remotely through a dedicated mobile application. This feature not only enhances convenience but also allows for enhanced security by enabling users to monitor their homes in real-time. The device is equipped with motion sensors and alert systems that can notify homeowners of any unusual activity, adding an extra layer of protection.

Both devices integrate seamlessly with existing smart home ecosystems, supporting popular communication protocols such as Zigbee and Z-Wave. This compatibility allows users to expand their systems by adding other smart devices, creating a fully integrated home automation experience.

In terms of installation, both Murray models are designed to be user-friendly. They typically come with comprehensive instructions, and many features can be accessed with minimal technical knowledge. The focus on ease of use extends to their maintenance, with straightforward troubleshooting and support available through the manufacturers.

Another important feature of both devices is their commitment to sustainability. By helping families monitor and manage their energy consumption, they play a crucial role in promoting more eco-friendly practices within households. Combined, Murray 1737920 and 1695722 stand out as leaders in smart home technology, emphasizing efficiency, security, and user-centric design principles that cater to the evolving needs of modern homeowners. These innovations represent a significant step forward in creating energy-conscious and secure living environments.
Top Page Image Contents