Sears 247.88853 owner manual Skid Shoe, Tire Pressure Pneumatic Tires

Page 11

If you face resistance when moving the shift lever or the snow thrower wheels stop when they should not, loosen the lock nut on the traction drive cable and unthread the cable one turn.

If the wheels can still be turned when you engage the traction drive clutch grip, loosen the lock nut on the traction drive cable and thread the cable in one turn.

Recheck the adjustment and repeat adjustment as necessary. Tighten the jam nut to secure the cable when correct adjustment is reached.

NOTE: If you are not sure that you have reached correct adjustment, refer to the Adjustment section on page 20.

Skid Shoe

The space between the shave plate and the ground can be adjusted. For close snow removal, place skid shoes in the low position. Use middle or high position when area to be cleared is uneven.

NOTE: It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing an injury or damage to the snow thrower.

If for some reason, you have to operate the snow thrower on gravel, keep the skid shoe in the highest

position for maximum clearance between the ground and the shave plate.

Adjust skid shoes by loosening the four hex nuts and carriage bolts and moving skid shoes to desired position.

Make certain the entire bottom surface of skid shoe is against the ground to avoid uneven wear on the skid shoes.

Tighten nuts and bolts securely.

Skid Shoe

Loosen these hardware to adjust skid shoe

Figure 16

Tire Pressure (Pneumatic Tires)

The tires are over-inflated for shipping purposes. Check tire pressure and reduce to 15 to 20 psi.

NOTE: If the tire pressure is not equal in both tires, the unit may pull to one side or the other.

11

Image 11
Contents Snow Thrower Warranty Information Table of ContentsTraining Safe Operation PracticesMaintenance & Storage Hardware Pack Assembly Attaching Chute Crank Attaching ChuteAttaching Clutch Cables Attaching Turn Triggers Attaching Shift RodAuger Control Lamp WiringFinal Adjustments Chute Clean-Out ToolSkid Shoe Skid ShoeTire Pressure Pneumatic Tires Operating Controls OperationKnowing Your Snow Thrower Before Starting Engine Stopping Snow ThrowerCold Start To Start EngineFill Oil Electric StarterRecoil Starter To Engage DriveTo Engage Augers To Throw SnowTo Stop The Snow Thrower Operating TipsBefore Stopping Lubrication MaintenanceGeneral Recommendations Check Friction Wheel Engine MaintenanceCheck V-Belts Nearby areas may exceed 150o F65oC. Avoid these areas Spark PlugChecking Oil Level Changing OilAdjustments Service & AdjustmentsReplacing Belt ServiceCarburetor AugersPush Reassemble new friction wheel rubber to Changing Friction Wheel RubberDrive Belt Between the friction wheel plate. See FigureCarburetor Preparing the Engine OFF-SEASON StorageProblem Cause Remedy TROUBLE-SHOOTING777I20727 Labels List & LocationRepair Parts Key Description Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Polo Green Powder Black Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Model Sears Craftsman 9.0 H.P. Snow ThrowerPage Key Part Description Qty Recoil Starter Carburetor Numero De Modelo Garantia DE InformaciónFuncionamiento Practicas Seguras DE OperacionCapacitación PreparaciónSu responsabilidad Mantenimiento & Almacenamiento16-18 x Conjunto DE Ferreteria DE Ferreteria20 x Ensamblado Canaleta de descarga Fijacion De La CanaletaFijacion De La Manivela De La Canaleta De la Pasador Casquillo plástico Manija de La canaletaManija SuperiorFijacion De Los Gatillos De Giro Fijacion De La Vara De CambiosAjustes Finales Cableado de la LámparaHerramienta de limpieza de la canaleta Conozca Su Expulsor De Nieve OperacionConociendo a su expulsor de nieve Antes de poner en marcha el motor Detencion Del Expulsor De NieveLlenado De Aceite Para Poner En Marcha El MotorManejo De La Limpiadora De Nieve Como Apagar El MotorEnganche De La Propulsion Herramienta de limpieza de canale Broche de cabello Enganche De Las Espirales Sin FinPresion De La Ruedas Consejos De OperacionEje De Engranajes MantenimientoRecomendaciones Generales LubricacionVerificar La Rueda De Fricción Verificar Las Correas EnBujia Mantenimiento Del MotorAceite De Motor Cambio De AceiteAjustes Service & AjustesService Correas de la espiral sin fin Plancha Raspadora Y Zapatas DeslizantesReemplazo De La Correa Nota Sea precavido para evitar apretar el cable de control Correa propulsoraCubrierta del propulsor Cambio De La Goma De La Rueda De FriccionCarburador Carburador Drenaje del tazón Almacenamiento DE Fuera DE TemporadaPreparación del motor Preparación del Expulsor de NieveTabla DE Localizacion DE Fallas Problema Causas Accion correctoraSears Parts & Repair Center Canada