Sears 247.88853 owner manual Attaching Chute Crank

Page 7

Discharge

Chute

Align holes here

Align holes here

•Attach the left handle in the same manner. Do not tighten at this time.

Attaching Chute

•Place the chute assembly over the chute opening with the chute facing front of the unit.

NOTE: Make sure that the chute cables are straightened while assembling the chute.

•Place the chute flange keeper (flat side down) beneath lip of chute assembly as shown in Figure 4 .You will find the chute flange keepers in group E of the hardware pack.

•Insert hex bolt (1/4-20 x .75”) and flange nut from group E up through chute flange keeper and chute assembly as shown in Figure 4 . Do not tighten at this time. Rotate chute to install all flange keepers.

Chute

Hex

Bolt Hex

Flange

Nut

Figure 2

•Secure bottom hole on the handle to the snow thrower frame using 5/16 x .75" hex bolt and lock washer from the hardware pack (group A on page 5 ). Do not tighten at this time. See Figure 3 .

Attach handle tab here

Attach lock washer and hex bolt here

NOTE: The right wheel and drive cover have been removed from picture here for viewing clarity.

Figure 3

•Place a handle tab, included in the hardware pack (group A on page 5), over the upper hole in handle so that the contour of the handle tab matches that of the handle. See Figure 3 .

•Secure handle tab to the snow thrower using hex bolt (5/16 x 2.0" long) and lock washer from the same group in the hardware pack. Do not tighten at this time.

Chute

Flange

Keeper

Figure 4

•After assembling all three chute flange keepers, tighten, then back off 1/4 turn to allow easier movement of the chute. Use (2) 7/16" wrenches.

Attaching Chute Crank

•You may have to loosen the carriage bolts and hex lock nuts which secure the lower chute crank bracket to the extension on the left side of the chute assembly. See Figure 5 .

Lower Chute		Carriage Bolt
Crank Bracket		Loosen hex nuts here
		Loosen hex nuts here

Figure 5

•Place one 3/8 ID flat washer (from group F of the hardware pack) on the end of the chute crank,

7

Image 7

Contents Snow Thrower Warranty Information Table of ContentsTraining Safe Operation PracticesMaintenance & Storage Hardware Pack Assembly Attaching Chute Crank Attaching ChuteAttaching Clutch Cables Attaching Turn Triggers Attaching Shift RodAuger Control Lamp WiringFinal Adjustments Chute Clean-Out ToolTire Pressure Pneumatic Tires Skid ShoeSkid Shoe Knowing Your Snow Thrower OperationOperating Controls Before Starting Engine Stopping Snow ThrowerCold Start To Start EngineFill Oil Electric StarterRecoil Starter To Engage DriveTo Engage Augers To Throw SnowBefore Stopping Operating TipsTo Stop The Snow Thrower General Recommendations MaintenanceLubrication Check V-Belts Engine MaintenanceCheck Friction Wheel Nearby areas may exceed 150o F65oC. Avoid these areas Spark PlugChecking Oil Level Changing OilAdjustments Service & AdjustmentsReplacing Belt ServiceCarburetor AugersPush Reassemble new friction wheel rubber to Changing Friction Wheel RubberDrive Belt Between the friction wheel plate. See FigureCarburetor Preparing the Engine OFF-SEASON StorageProblem Cause Remedy TROUBLE-SHOOTING777I20727 Labels List & LocationRepair Parts Key Description Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Polo Green Powder Black Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Model Sears Craftsman 9.0 H.P. Snow ThrowerPage Key Part Description Qty Recoil Starter Carburetor Numero De Modelo Garantia DE InformaciónFuncionamiento Practicas Seguras DE OperacionCapacitación PreparaciónSu responsabilidad Mantenimiento & Almacenamiento20 x Conjunto DE Ferreteria DE Ferreteria16-18 x Ensamblado Fijacion De La Manivela De La Canaleta Fijacion De La CanaletaCanaleta de descarga De la Pasador Casquillo plástico Manija de La canaletaManija SuperiorFijacion De Los Gatillos De Giro Fijacion De La Vara De CambiosHerramienta de limpieza de la canaleta Cableado de la LámparaAjustes Finales Conociendo a su expulsor de nieve OperacionConozca Su Expulsor De Nieve Antes de poner en marcha el motor Detencion Del Expulsor De NieveLlenado De Aceite Para Poner En Marcha El MotorEnganche De La Propulsion Como Apagar El MotorManejo De La Limpiadora De Nieve Herramienta de limpieza de canale Broche de cabello Enganche De Las Espirales Sin FinPresion De La Ruedas Consejos De OperacionEje De Engranajes MantenimientoRecomendaciones Generales LubricacionVerificar La Rueda De Fricción Verificar Las Correas EnBujia Mantenimiento Del MotorAceite De Motor Cambio De AceiteService Service & AjustesAjustes Reemplazo De La Correa Plancha Raspadora Y Zapatas DeslizantesCorreas de la espiral sin fin Nota Sea precavido para evitar apretar el cable de control Correa propulsoraCubrierta del propulsor Cambio De La Goma De La Rueda De FriccionCarburador Carburador Drenaje del tazón Almacenamiento DE Fuera DE TemporadaPreparación del motor Preparación del Expulsor de NieveTabla DE Localizacion DE Fallas Problema Causas Accion correctoraSears Parts & Repair Center Canada